Husqvarna T540i XP with battery and charger Owner Manual - Page 28

Accessories, Recommended cutting equipment, Kickback information, Filing equipment and filing angles

Get Husqvarna T540i XP with battery and charger PDF manuals and user guides View all Husqvarna T540i XP with battery and charger manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Output power, max dBm 0 T540i XP 0 Accessories Recommended cutting equipment A specific chainsaw model has to be evaluated with the cutting equipment to be recommended and fulfill the requirements in ANSI B175.1-2012 (Internal Combustion Engine-Powered Hand-Held Chainsaws - Safety and Environmental Requirements) and Canadian Standards CSA Z62.1-15 (Chainsaws) and CSA Z62.3-11 (R2016) (Chainsaw kickback). Chainsaw models Husqvarna T540i XP met the safety requirements in ANSI B175.1-2012 and Canadian Standards Association CSA Z62.1-15 (Chainsaws) and CSA Z62.3-11 (R2016) (Chainsaw kickback), when equipped with the below listed saw chain and guide bar combination(s). Note: Other chainsaw models may not meet the kickback requirements when equipped with the listed guide bar and saw chain combinations. We recommend only to use the listed guide bar and saw chain combinations. Kickback information The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a solid bar. As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of sprocket teeth may be considered to have equivalent kickback energy. The following cutting equipment is approved for the models Husqvarna T540i XP. Guide bar Length, in 12 14 16 Chain pitch, in Gauge, in 0.325 mini 0.043 Saw chain Max. nose ra- Type dius 8T Husqvarna SP21G Length, drive links (no.) 51 59 64 Low kickback Yes Filing equipment and filing angles Using Husqvarna file gauge will give you the correct filing angles. We recommend you to always use a Husqvarna file gauge to restore the sharpness of the saw chain. The part numbers are given in the table below. If you do not know which saw chain you have on your product, turn to your servicing dealer. 21 5/32 in / 4.0 mm 60° 30° 0° 0.025 in/ 0.65 mm 5950046-01 5950047-01 28 1036 - 008 - 04.11.2021

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
T540i XP
Output power, max dBm 0
0
Accessories
Recommended cutting equipment
A specific chainsaw model has to be evaluated with the
cutting equipment to be recommended and fulfill the
requirements in ANSI B175.1-2012 (Internal Combustion
Engine-Powered Hand-Held Chainsaws - Safety and
Environmental Requirements) and Canadian Standards
CSA Z62.1-15 (Chainsaws) and CSA Z62.3-11 (R2016)
(Chainsaw kickback).
Chainsaw models Husqvarna T540i XP met the safety
requirements in ANSI B175.1-2012 and Canadian
Standards Association CSA Z62.1-15 (Chainsaws) and
CSA Z62.3-11 (R2016) (Chainsaw kickback), when
equipped with the below listed saw chain and guide bar
combination(s).
Note:
Other chainsaw models may not meet the
kickback requirements when equipped with the listed
guide bar and saw chain combinations.
We recommend only to use the listed guide bar and saw
chain combinations.
Kickback information
The guide bar nose radius is determined by either the
maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar.
As we are listing the maximum guide bar nose radius,
you may use a guide bar with smaller nose radius than
in our list. For guide bars of the same length, all
sprocket-nose guide bars of the same pitch and having
the same number of sprocket teeth may be considered
to have equivalent kickback energy.
The following cutting equipment is approved for the
models Husqvarna T540i XP.
Guide bar
Saw chain
Length, in
Chain pitch, in
Gauge, in
Max. nose ra-
dius
Type
Length, drive
links (no.)
Low kickback
12
0.325 mini
0.043
8T
Husqvarna
SP21G
51
Yes
14
59
16
64
Filing equipment and filing angles
Using Husqvarna file gauge will give you the correct
filing angles. We recommend you to always use a
Husqvarna file gauge to restore the sharpness of the
saw chain. The part numbers are given in the table
below.
If you do not know which saw chain you have on your
product, turn to your servicing dealer.
21
5/32 in / 4.0
mm
60°
30°
0°
0.025 in/
0.65 mm
5950046-01
5950047-01
28
1036 - 008 - 04.11.2021