Home » HP Manuals » Computer Monitors » HP MX703 » Manual Viewer

HP MX703 HP Pavilion V70s Monitor - (English) User Guide - Page 8

Suspend Mode: <10W

Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Specifications Power Source Power Consumption Picture Tube AC 100-240V, 50/60Hz (Full Range) 1 Normal: 100W Max. 2 Stand-by Mode:

Section	Page
user's guide	1
	2
	2
	2
	2
	2
The information contained in this document is subject to change without notice.	2
Hewlett-Packard® Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.	2
HP shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.	2
HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP.	2
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of HP.	2
Hewlett-Packard Company	2
Home Products Division	2
P.O. Box 4010	2
Cupertino, CA 95015-4010	2
Printed in the Taiwan	2
© Copyright Hewlett-Packard Company, 2000. All rights reserved.	2
Hewlett-Packard is a registered trademark of Hewlett-Packard Company in the United States of America and other countries.	2
The ENERGY STAR name is a U.S. Registered mark of the U.S. Environmental Protection Agency.	2
Other brand or product names are trademarks of their respective holders.	2
C	3
Contents	3
Introduction	4
Precautions	5
	5
	5
	5
Warning: This appliance should be grounded.	5
1 To reduce eye fatigue, avoid using the display in direct sunlight or other bright lights.	6
2 Do not operate the monitor beyond the specified temperature and humidity range	6
(see specifications).	6
3 For proper operation, keep the monitor adequately ventilated.	6
4 Keep the monitor away from transformers, motors, fans or strong magnetic fields.	6
5 If the monitor does not operate properly, turn off the power switch and then unplug the monitor.	6
6 When an irregular supply is applied, a protection circuit will turn off the monitor (the power indicator will also be turned off). If this happens, turn off the power switch and wait at least 30 seconds before turning it on again.	6
Features	7
	7
1 Automatically scans horizontal frequencies ranged from 30kHz to 70kHz and vertical frequencies ranged from 50Hz to 120Hz.	7
2 Meets DPMS and NUTEK power-saving standards.	7
3 All functions can be controlled by On-Screen Display.	7
4 Plug-and-play compatibility.	7
5 Full-scan display – 15.9-inch diagonal viewable image size.	7
6 Rotation (tilt control).	7
7 Self-test – When you disconnect the signal cable from the PC, the display will produce as below:	7
8 Color temperature selection – 9300K / 7000K / 6500K and user adjustable.	7
Specifications	8
Installing the Base Pedestal	10
	10
	10
1 Turn the monitor upside down on a sturdy surface. (Don’t place it screen-side down; the glass can be scratched.)	10
2 Position the base pedestal with the latch facing the back of the monitor.	10
3 Insert the seven tabs on the base pedestal into the seven slots found on the bottom of the monitor.	10
4 Push the base pedestal toward the front of the monitor until it snaps into position.	10
Control Locations and Functions	11
	11
	11
	11
Note: Locations of display controls are shown below. Operation of controls is explained in the following pages.	11
	11
	11
FRONT	11
REAR	11
Controls and Adjustments	12
	14
	14
	14
	14
	14
	14
Menu display will be closed automatically in 20 seconds.	14
Connections	18
	18
1 Make sure the monitor and computer are turned off. (See previous section on safety.)	18
2 Connect the power cord to the back of the display.	18
3 Plug the other end of the cable into a grounded outlet.	18
4 Connect the video cable on the monitor to the 15-pin video graphics connector on the rear panel of the computer, and fasten the screws.	18
	18
Note: Don’t force the cable into the connector; line it up carefully so you don’t bend the pins.	18
Pin Assignments and Signal Levels	20
	20
	20
	20
Note: The signal level at pin 1,2,3 is 0.7 Vp-p.	20
The signal level at pin 13,14 is 5 Vp-p.	20
Timing Charts	21
Troubleshooting	24
Automatic Power Saving	25
Declaration of	28