Harman Kardon AVR 146 Owners Manual - Page 33

Auto Poll, Dmp Setting, Repeat, Shuffle, Resume, Charge In St-by - replacement remote

Get Harman Kardon AVR 146 PDF manuals and user guides View all Harman Kardon AVR 146 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

INITIAL SETUP AUTO POLL: The Auto Poll feature is used when both an analog audio and digital audio connection have been made for one source device. If for some reason no digital signal is available, the AVR 146 will switch to the analog inputs for the source. This situation can occur with some cable or satellite television broadcasts, where some channels are broadcast with digital audio and others with analog audio. For some sources, the Auto Poll feature is unnecessary and may be undesirable. For example, if your DVD player is stopped, you may not want to use the analog audio signal or you may have decided not to connect analog audio. Move the cursor to this line, and press the ‹/› Buttons until OFF appears, disabling the Auto Poll feature. With Auto Poll turned off, the receiver will only check for a signal at the audio input assigned to the source. DMP SETTING: If you select DMP/The Bridge as your source input, you will notice that the AUDIO IN line of the INPUT SETUP menu has been replaced by the option GO TO DMP SETTING. See Figure 48. Figure 48 - Input Setup Menu Screen for DMP/The Bridge source Since The Bridge is connected to the AVR using a dedicated audio connection, it isn't possible to select a different audio input for this source. However, there are several special settings used only with The Bridge. Selecting GO TO DMP SETTING displays the DMP SETTING menu (see Figure 49). REPEAT: Set REPEAT to ONE, ALL or OFF to repeat one track, all tracks in an album or playlist, or not to repeat any tracks. SHUFFLE: Set SHUFFLE to SONGS to play all songs on the iPod in random order. The ALBUMS setting plays all albums in random order, with each album's tracks played in album order. RESUME: Set RESUME to ON to resume playback of a track from the point where it was interrupted by turning off the AVR, switching sources on the AVR, or removing the iPod from The Bridge. Set RESUME to OFF if you wish to restart play from the beginning of the track after interruptions. NOTE: The Resume setting disables the Remember Playback Position setting that you may set for audio and video files using later versions of iTunes. Resume affects all files on the iPod until you manually change the setting either in the DMP SETTING menu or by using iTunes. CHARGE IN ST-BY: Your iPod's battery may be charged while it is docked in The Bridge with the AVR turned on. Set CHARGE IN ST-BY to ON to enable charging even when the AVR is in Standby mode (but not completely off). When CHARGE IN ST-BY is set to OFF, the iPod will charge only when the AVR is turned on. NOTE: In order to access the DMP SETTING menu, press the AVR Selector on the remote so that it operates the AVR 146. You may then press the OSD Button and use the Navigation and Set Buttons, as usual, with the on-screen menu system. When you are ready to return to operation of your iPod using the remote, remember to press the DMP/The Bridge Selector so that the transport and other controls operate The Bridge. To simplify use, you may wish to program two macros on your remote, one to select the AVR and issue the commands within the OSD system to display the DMP SETTING menu, and a second macro to remove the menu from the display and return the remote to operation of The Bridge. See the Macros section of the Advanced Functions section of the manual for more information on programming macros. The remaining lines in the Input Setup menu activate the tone controls, and may be skipped at this time. We recommend leaving the tone controls at their factory defaults for most listening, in order to enjoy the sound mix created by your favorite movie and music artists. However, if your room or speakers have unusual characteristics, or simply as a matter of personal preference, see the Tone Controls section on page 35 for more information. You are now ready to begin enjoying your new receiver! Figure 49 - DMP Setting Menu Screen MODE: The first line of the DMP SETTING menu allows you to select whether the iPod will be used to listen to music (or other audio materials), or view a video or still image, if your iPod is video- or photo-capable. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
33
INITIAL SETUP
AUTO POLL:
The Auto Poll feature is used when both an analog
audio and digital audio connection have been made for one source
device. If for some reason no digital signal is available, the AVR 146
will switch to the analog inputs for the source. This situation can occur
with some cable or satellite television broadcasts, where some channels
are broadcast with digital audio and others with analog audio.
For some sources, the Auto Poll feature is unnecessary and may be
undesirable. For example, if your DVD player is stopped, you may not
want to use the analog audio signal or you may have decided not
to connect analog audio. Move the cursor to this line, and press the
‹
/
›
Buttons until OFF appears, disabling the Auto Poll feature. With
Auto Poll turned off, the receiver will only check for a signal at the
audio input assigned to the source.
DMP SETTING:
If you select DMP/The Bridge as your source input,
you will notice that the AUDIO IN line of the INPUT SETUP menu has
been replaced by the option GO TO DMP SETTING. See Figure 48.
Figure 48 – Input Setup Menu Screen for DMP/The Bridge source
Since The Bridge is connected to the AVR using a dedicated audio
connection, it isn’t possible to select a different audio input for this
source. However, there are several special settings used only with
The Bridge. Selecting GO TO DMP SETTING displays the DMP SETTING
menu (see Figure 49).
Figure 49 – DMP Setting Menu Screen
MODE:
The first line of the DMP SETTING menu allows you to
select whether the iPod will be used to listen to music (or other audio
materials), or view a video or still image, if your iPod is video- or
photo-capable.
REPEAT:
Set REPEAT to ONE, ALL or OFF to repeat one track, all
tracks in an album or playlist, or not to repeat any tracks.
SHUFFLE:
Set SHUFFLE to SONGS to play all songs on the iPod in
random order.The ALBUMS setting plays all albums in random order,
with each album’s tracks played in album order.
RESUME:
Set RESUME to ON to resume playback of a track from
the point where it was interrupted by turning off the AVR, switching
sources on the AVR, or removing the iPod from The Bridge. Set
RESUME to OFF if you wish to restart play from the beginning of
the track after interruptions.
NOTE:
The Resume setting disables the Remember Playback
Position setting that you may set for audio and video files using
later versions of iTunes. Resume affects all files on the iPod until
you manually change the setting either in the DMP SETTING
menu or by using iTunes.
CHARGE IN ST-BY:
Your iPod’s battery may be charged while it is
docked in The Bridge with the AVR turned on. Set CHARGE IN ST-BY to
ON to enable charging even when the AVR is in Standby mode (but not
completely off).When CHARGE IN ST-BY is set to OFF, the iPod will
charge only when the AVR is turned on.
NOTE:
In order to access the DMP SETTING menu, press the
AVR Selector on the remote so that it operates the AVR 146.
You may then press the OSD Button and use the Navigation
and Set Buttons, as usual, with the on-screen menu system.
When you are ready to return to operation of your iPod using
the remote, remember to press the DMP/The Bridge Selector
so that the transport and other controls operate The Bridge.
To simplify use, you may wish to program two macros on your
remote, one to select the AVR and issue the commands within
the OSD system to display the DMP SETTING menu, and a
second macro to remove the menu from the display and return
the remote to operation of The Bridge. See the Macros section
of the Advanced Functions section of the manual for more
information on programming macros.
The remaining lines in the Input Setup menu activate the tone controls,
and may be skipped at this time. We recommend leaving the tone
controls at their factory defaults for most listening, in order to enjoy the
sound mix created by your favorite movie and music artists. However,
if your room or speakers have unusual characteristics, or simply as
a matter of personal preference, see the Tone Controls section on page
35 for more information.
You are now ready to begin enjoying your new receiver!