Harbor Freight Tools 68148 User Manual
Harbor Freight Tools 68148 - 10 Amp, 120 Volt Demolition Hammer Manual
 |
View all Harbor Freight Tools 68148 manuals
Add to My Manuals
Save this manual to your list of manuals |
Harbor Freight Tools 68148 manual content summary:
- Harbor Freight Tools 68148 | User Manual - Page 1
DEMOLITION HAMMER Model 68148 SET UP AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. Copyright© 2010 by Harbor Freight Tools®. All rights reserved. No portion - Harbor Freight Tools 68148 | User Manual - Page 2
number). Keep this manual and the receipt in a safe and dry place for future reference. IMPORTANT SAFETY INFORMATION In this manual, on the labeling, . General Power Tool Safety Warnings WARNING Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in - Harbor Freight Tools 68148 | User Manual - Page 3
starting the power tool accidentally. d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. SKU 68148 For technical questions, please - Harbor Freight Tools 68148 | User Manual - Page 4
carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 9. Avoid unintentional starting. Prepare to begin work before turning on the tool. 5. Service a. Have your power tool serviced by a qualified repair person using only identical replacement - Harbor Freight Tools 68148 | User Manual - Page 5
and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant tool do the work. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. SKU 68148 - Harbor Freight Tools 68148 | User Manual - Page 6
2. plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the using it. Page 6 For technical questions, please call 1-800-444-3353. SKU 68148 - Harbor Freight Tools 68148 | User Manual - Page 7
rated amperes. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ Volts Alternating Current A Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) SKU 68148 For technical questions, please call 1-800-444-3353. Page 7 - Harbor Freight Tools 68148 | User Manual - Page 8
Harbor Freight Tools at 1‑800‑444‑3353 as soon as possible. INSTRUCTIONS FOR PUTTING INTO USE Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual near the end of this manual. Functions Use Figure 1 below as reference during Tool Setup and Operation. Trigger (69 - Harbor Freight Tools 68148 | User Manual - Page 9
's own weight supplies the needed force. 6. NOTE: If the Demolition Hammer has not been used for a long period of time or is being used in low temperatures, keep the tool running for about five minutes to allow for warm-up. Make SKU 68148 For technical questions, please call 1-800-444-3353. Page 9 - Harbor Freight Tools 68148 | User Manual - Page 10
power supply after use. Clean, then store the tool indoors out of children's reach. MAINTENANCE AND SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician. NOTE: The Demolition Hammer will cease operation once Carbon Brushes are worn. Check - Harbor Freight Tools 68148 | User Manual - Page 11
Hammer. Doing so can damaged the tool. Troubleshooting Problem Tool will not start. Possible Causes 1. Cord not connected. 2. No power at outlet. 3. Tool precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. SKU 68148 For technical questions, please call - Harbor Freight Tools 68148 | User Manual - Page 12
(Ø18xØ30x6) Gear Inner Cover Ball Bearing (6001) Impact Block Ring Needle Bearing (BK1312) Impact Hammer L-Ring (Ø27xØ36x6.5) O-Ring (Ø26.4xØ3.5) O-Ring (Ø38xØ2) Qty 1 4 1 1 ) Brush Terminal Fan Guide Tapping Screw (ST4. Handle Clamp Insulating Washer Support Rivet Trigger Main Handle . SKU 68148 - Harbor Freight Tools 68148 | User Manual - Page 13
ASSEMBLY DIAGRAM SKU 68148 For technical questions, please call 1-800-444-3353. Page 13 - Harbor Freight Tools 68148 | User Manual - Page 14
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF , please call 1-800-444-3353. SKU 68148
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
DEMOLITION HAMMER
Model
68148
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
©
2010 by Harbor Freight Tools
®
.
All rights reserved.
No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally.
Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1‑800‑444‑3353.