Gateway E-9520T User Guide - Page 58

Follow the instructions in, Set the chassis upright, if necessary.

Get Gateway E-9520T PDF manuals and user guides View all Gateway E-9520T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

CHAPTER 4: Installing Components www.gateway.com 10 Remove the backplane and place it in a static-free bag for storage. 11 Holding the new backplane by the edges only, align it with the locking tabs on the hard drive cage, then place it on the locking tabs and slide it up. 12 Tighten the thumbscrew to secure the backplane to the hard drive cage. 13 Slide the hard drive cage back into the opening in the front of the chassis until it clicks into place. 14 Reconnect all cables to the backplane. Connect to Mezzanine Board 15 Replace the system fans by following the instructions in "Replacing system fans" on page 43. 16 Set the chassis upright, if necessary. 17 Follow the instructions in "Closing the server case" on page 30. 18 Reinstall the hot-swap drives back into the server. Make sure that you install the drives into the same bays you removed them from in Step 4. For instructions see "Removing and installing a hard drive" on page 33. 19 Replace the bezel by snapping it into place on the front of the server. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
CHAPTER 4: Installing Components
www.gateway.com
52
10
Remove the backplane and place it in a static-free bag for storage.
11
Holding the new backplane by the edges only, align it with the locking
tabs on the hard drive cage, then place it on the locking tabs and slide it
up.
12
Tighten the thumbscrew to secure the backplane to the hard drive cage.
13
Slide the hard drive cage back into the opening in the front of the chassis
until it clicks into place.
14
Reconnect all cables to the backplane.
15
Replace the system fans by following the instructions in
“Replacing system
fans” on page 43.
16
Set the chassis upright, if necessary.
17
Follow the instructions in
“Closing the server case” on page 30
.
18
Reinstall the hot-swap drives back into the server. Make sure that you
install the drives into the same bays you removed them from in
Step 4
. For
instructions see
“Removing and installing a hard drive” on page 33
.
19
Replace the bezel by snapping it into place on the front of the server.
Connect to Mezzanine Board