Garmin GPSMAP 8410xsv Installation Instructions PDF - Page 2
Mounting the Device
![]() |
View all Garmin GPSMAP 8410xsv manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
1 Using the bail-mount bracket holes . as a template, mark the pilot 6 If necessary, use a file and sandpaper to refine the size of the cutout. 7 After the device fits correctly in the cutout, ensure the mounting holes on the device line up with the larger 6 mm (1/4 in.) holes on the template. 8 If the mounting holes on the device do not line up, mark the new hole locations. 9 Based on your mounting surface, drill or punch and tap the larger holes: • Drill 3.2 mm (1/8 in.) pilot holes for the included wood screws, and skip to step 18. • Drill 6 mm (1/4 in.) holes for the included nut plate and machine screws. • Drill and tap M4 holes for the included machine screws, and skip to step 18. 10If using the nut plates, starting in one corner of the template, place a nut plate over the larger hole drilled in step 9. 2 Using a 3 mm (1/8 in.) drill bit, drill the pilot holes. 3 Secure the bail-mount bracket to the surface using the included washers and wood screws . 4 Install the bail-mount knobs on the sides of the device. 5 Place the device in the bail-mount bracket, and tighten the bail-mount knobs. 6 Install the trim caps by snapping them in place around the edges of the device. Mounting the Device NOTICE Be careful when cutting the hole to flush mount the device. There is only a small amount of clearance between the case and the mounting holes, and cutting the hole too large could compromise the stability of the device after it is mounted. Use only the included hardware when mounting this device. Using mounting hardware not provided with the device may damage the device. To avoid potential damage to the powder coating, use only the included screws to mount the device. Using screws other than the ones included will void your warranty. Do not remove the blue, rubber protective bumper until after the installation is complete. The bumper helps protect the device from damage during installation. If you will not have access to be back of the device and the microSD memory card slots after installations, you should install the microSD memory card prior to installation. The included template and hardware can be used to flush mount the device in your dashboard. There are three options for hardware based on the mounting surface material. • You can drill pilot holes and use the included wood screws. • You can drill holes and use the included nut plates and machine screws. The nut plates can add stability to a thinner surface. • You can drill holes, tap them to M4, and use the included machine screws. 1 Trim the template and make sure it fits in the location where you want to mount the device. 2 Secure the template to the selected location. 3 Using an 14.6 mm (9/16 in.) drill bit, drill one or more of the holes inside the corners of the solid line on the template to prepare the mounting surface for cutting. 4 Using a jigsaw or rotary tool, cut the mounting surface along the inside of the solid line on the template. 5 Place the device in the cutout to test the fit. The smaller hole on the nut plate should line up with the smaller 3.6 mm (9/64 in.) hole on the template. 11If the smaller hole on the nut plate does not line up with the smaller hole on the template, mark the new hole location. 12Repeat steps 10 and 11 for each nut plate. 13Using a 3.6 mm (9/64 in.) drill bit, drill the smaller holes. 14Remove the template from the mounting surface. 15Starting in one corner of the mounting location, place a nut plate on the back of the mounting surface, lining up the large and small holes. The raised portion of the nut plate should fit into the larger hole. 16Secure the nut plate to the mounting surface by fastening an included M3 screw through the smaller 3.6 mm (9/64 in.) hole. 17Repeat steps 15 and 16 for each of the nut plates along the top and bottom of the device. 18Install the foam gasket on the back of the device. The pieces of the foam gasket have adhesive on the back. Make sure you remove the protective liner before installing them on the device. 19If you will not have access to the back of the device after you mount it, connect all necessary cables and install microSD cards in the back of the device before placing it into the cutout. 2
![](/manual_guide/products/garmin-gpsmap-84008600-installation-instructions-pdf-00cf3be/2.png)