Fisher and Paykel HCB36-12_N Installation Guide - Page 29

Important, Warning

Get Fisher and Paykel HCB36-12_N PDF manuals and user guides View all Fisher and Paykel HCB36-12_N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

MAINTENANCE EN Light bulb replacement IMPORTANT! ● Wear gloves to protect against sharp edges. ● DO NOT TOUCH the light bulb when in use. They may be hot enough to cause injury. Note: Replacement bulbs are not covered by warranty. To replace the light bulb: ● Turn off the range hood and allow the light bulb to cool. ● Disconnect the power. ● To remove the light bulb push up and twist counterclockwise. ● Replace with a new 120V, 50W maximum light bulb (or equivalent dimmable LED) light with a GU10 base. ● Repeat steps for the other light bulbs if needed. ● Reconnect power. ● If new lights do not operate, ensure the bulbs are inserted correctly before calling a service representative. Replacing the infra-red heat lamp (optional accessory) WARNING! To avoid any electrical shock the installation of the infra-red heat lamp and panel kit should be done by a qualified electrician and before starting the installation of the range hood. Optional infra-red heat lamp panel can be ordered separately and mounted into your range hood, see the 'Parts and accessories' section. ● Turn off the range hood and allow the infra-red heat lamp to cool. ● Disconnect the power. ● Remove the infra-red heat lamp bulb by twisting counter clockwise. ● Replace with a new 120V, 175W maximum infra-red bulb with a E26 screw in fitting. ● Repeat steps for the other lamp if needed. ● Reconnect power. ● If new lamps do not operate, ensure the bulbs are inserted correctly before calling a service representative. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
27
MAINTENANCE
Light bulb replacement
IMPORTANT!
●
Wear gloves to protect against sharp edges.
●
DO NOT TOUCH the light bulb when in use. They may be hot enough to cause injury.
Note: Replacement bulbs are not covered by warranty.
To replace the light bulb:
●
Turn off the range hood and allow the light bulb to cool.
●
Disconnect the power.
●
To remove the light bulb push up and twist counterclockwise.
●
Replace with a new 120V, 50W maximum light bulb (or equivalent dimmable LED)
light with a GU10 base.
●
Repeat steps for the other light bulbs if needed.
●
Reconnect power.
●
If new lights do not operate, ensure the bulbs are inserted correctly before calling
a service representative.
Replacing the infra-red heat lamp (optional accessory)
WARNING!
To avoid any electrical shock the installation of the infra-red heat lamp and panel kit
should be done by a qualified electrician and before starting the installation of the
range hood.
Optional infra-red heat lamp panel can be ordered separately and mounted into
your range hood, see the ‘Parts and accessories’ section.
●
Turn off the range hood and allow the infra-red heat lamp to cool.
●
Disconnect the power.
●
Remove the infra-red heat lamp bulb by twisting counter clockwise.
●
Replace with a new 120V, 175W maximum infra-red bulb with a E26 screw in fitting.
●
Repeat steps for the other lamp if needed.
●
Reconnect power.
●
If new lamps do not operate, ensure the bulbs are inserted correctly before calling
a service representative.
EN