Epson U220D User Manual - Page 17

Returning the autocutter blade to the normal position, Removing jammed paper, CAUTION

Get Epson U220D - TM Two-color Dot-matrix Printer PDF manuals and user guides View all Epson U220D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

English ERROR LED is flashing or lit ❏ The print head temperature may be too high or low. Wait until the print head cools or warms and the printer resumes printing automatically. ❏ Make sure that the roll paper cover is properly closed. ❏ Types A and B: The autocutter blade is not in the normal position and the autocutter is locked up. If it is a simple lock-up, the error is corrected automatically. If not, see the instructions below to return the blade to the normal position manually. ❏ A paper jam has occurred. To remove the jammed paper, see the instructions below. ❏ Turn off the power, wait several seconds, and then turn it on again. If the error remains, contact your supervisor or a qualified service person. Returning the autocutter blade to the normal position 1. Open the roll paper cover by using the tab, as shown in illustration H. 2. Use a ballpoint pen or tweezers to turn the knob of the autocutter in the direction indicated by the arrow until you see a round shaft in the hole, as shown in illustration P. Removing jammed paper CAUTION: The print head becomes very hot during printing. Allow it to cool before you reach into the printer. 1. Open the roll paper cover by using the tab, as shown in illustration H. 2. If you have a Type A printer, remove the take-up spool and open the unit by using the unit open lever, as shown in illustration I. 3. Remove the jammed paper. 4. Re-insert the roll paper and close the roll paper cover. TM-U220 User's Manual 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
TM-U220 User’s Manual
9
English
ERROR
LED is flashing or lit
❏
The print head temperature may be too high or low. Wait until the
print head cools or warms and the printer resumes printing
automatically.
❏
Make sure that the roll paper cover is properly closed.
❏
Types A and B: The autocutter blade is not in the normal position
and the autocutter is locked up. If it is a simple lock-up, the error is
corrected automatically. If not, see the instructions below to return
the blade to the normal position manually.
❏
A paper jam has occurred. To remove the jammed paper, see the
instructions below.
❏
Turn off the power, wait several seconds, and then turn it on
again. If the error remains, contact your supervisor or a qualified
service person.
Returning the autocutter blade to the normal position
1.
Open the roll paper cover by using the tab, as shown in
illustration H.
2.
Use a ballpoint pen or tweezers to turn the knob of the autocutter
in the direction indicated by the arrow until you see a round shaft
in the hole, as shown in illustration P.
Removing jammed paper
CAUTION:
The print head becomes very hot during printing. Allow it to cool before
you reach into the printer.
1.
Open the roll paper cover by using the tab, as shown in
illustration H.
2.
If you have a
Type A
printer, remove the take-up spool and open
the unit by using the unit open lever, as shown in illustration I.
3.
Remove the jammed paper.
4.
Re-insert the roll paper and close the roll paper cover.