Epson Home Cinema 2100 Quick Setup and Warranty - Page 2

Adjust the image, Using the remote control, Viewing 3D images - projector

Page 2 highlights

Adjust the image 1 If you don't see an image, press the Source button on the projector or one of the source buttons on the remote control to select the image source. Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet. 2 To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position. Using the remote control Install the batteries as shown (two AA batteries). Turn projector on and off Choose which source to display 3 To reduce or enlarge the image, turn the zoom ring. 4 To sharpen the image, turn the focus ring. 5 If your image looks like or , you may have placed the projector off to one side of the screen at an angle. Place the projector directly in front of the center of the screen, facing the screen squarely. If you can't move the projector, use the horizontal keystone slider on the projector to correct the image shape. Control connected devices with HDMI Link Access projector menus Switch between 2D and 3D Navigate projector menus Access the Home screen For more information on using the remote control, see the online User's Guide. Viewing 3D images To view 3D content, you must first connect a 3D-compatible video device to one of the HDMI ports on your projector. You also need a pair of Epson® (part number V12H548006) or Epson-compatible RF 3D active shutter glasses. 1 Turn on and begin playback on the 3D-compatible video device. Note: Make sure you set the video device to play content in 3D mode. 2 Press the 2D/3D button on the remote control, if necessary. 3 Slide the power switch on your 3D glasses to the On position. 6 Your projector automatically adjusts images that look like or , but if necessary you can press the or buttons on the projector to correct it. Note: If the glasses don't automatically display 3D content, you may need to pair them with the projector. Move the glasses within 10 feet (3 m) of the projector, then press and hold the Pairing button on the 3D glasses for at least 3 seconds. The status light on the glasses will alternately flash green and red, then remain green for 10 seconds if pairing is successful. You can also automatically convert 2D HDMI content to 3D. To enable the 2D-to-3D Conversion option, press the Menu button on the projector or remote control. Select Signal and press Enter, then select 3D Setup and press Enter. Select 2D-to-3D Conversion and press Enter. Select the Weak, Medium, or Strong setting, then press Enter. See the online User's Guide for more information on adjusting 3D images.

  • 1
  • 2
  • 3
  • 4

Adjust the image
1
If you don’t see an image, press the
Source
button on the projector or
one of the source buttons on the remote control to select the image
source.
Note:
If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
3
To reduce or enlarge the image, turn the zoom ring.
4
To sharpen the image, turn the focus ring.
5
If your image looks like
or
, you may have placed the projector
off to one side of the screen at an angle. Place the projector directly in
front of the center of the screen, facing the screen squarely. If you can’t
move the projector, use the horizontal keystone slider on the projector to
correct the image shape.
6
Your projector automatically adjusts images that look like
or
,
but if necessary you can press the
or
buttons on the projector to
correct it.
Using the remote control
Install the batteries as shown (two AA batteries).
Choose which source
to display
Turn projector
on and off
Control connected
devices with HDMI Link
Switch between
2D and 3D
Access the Home
screen
Navigate projector
menus
Access projector
menus
For more information on using the remote control, see the online
User’s Guide
.
Viewing 3D images
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector. You also need a pair of Epson
®
(part
number V12H548006) or Epson-compatible RF 3D active shutter glasses.
1
Turn on and begin playback on the 3D-compatible video device.
Note:
Make sure you set the video device to play content in 3D mode.
2
Press the
2D/3D
button on the remote control, if necessary.
3
Slide the power switch on your 3D glasses to the
On
position.
Note:
If the glasses don’t automatically display 3D content, you may need
to pair them with the projector. Move the glasses within 10 feet (3 m) of
the projector, then press and hold the
Pairing
button on the 3D glasses
for at least 3 seconds. The status light on the glasses will alternately flash
green and red, then remain green for 10 seconds if pairing is successful.
You can also automatically convert 2D HDMI content to 3D. To enable the
2D-to-3D Conversion option, press the
Menu
button on the projector or remote
control. Select
Signal
and press
Enter
, then select
3D Setup
and press
Enter
.
Select
2D-to-3D Conversion
and press
Enter
. Select the
Weak
,
Medium
, or
Strong
setting, then press
Enter
.
See the online
User’s Guide
for more information on adjusting 3D images.