Dewalt DCN680D1 Instruction Manual - Page 14

Headlights Fig. I, Clearing a Jammed Nail Fig. A, J, Cold Weather Operation, Hot Weather Operation,

Get Dewalt DCN680D1 PDF manuals and user guides View all Dewalt DCN680D1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

English Fig. H 3 13 Headlights (Fig. I) There is a headlight 4 located on each side of the nailer. Headlights turn on upon battery insertion, activation of the trigger, or depressing the contact trip. The lights will automatically shut off after 20 seconds unless tool remains in use. Fig. I 6. Close the nosepiece door and engage the latch pin under the two arms on the nosepiece. Push latch until it locks in place. 7. Reinsert battery pack. NOTE: The tool will disable itself and not reset until the battery pack has been removed and reinserted. 8. Reinsert nails into magazine (see Loading the Tool). Fig. J 5 4 NOTE: These headlights are for lighting the immediate work surface and are not intended to be used as flashlights. LOW BATTERY INDICATOR: The left-side headlight will flash four consecutive times and then shut down to indicate low battery. JAMMED NAIL INDICATOR: The right-side headlight will flash continually if a nail becomes jammed in the nosepiece (see Clearing a Jammed Nail). Clearing a Jammed Nail (Fig. A, J) If a nail becomes jammed in the nosepiece, keep the tool pointed away from you and follow these instructions to clear: 1. Remove battery pack from tool and engage the trigger lock-off. 2. Press the magazine latch 16 and remove any loaded nails. 3. Lift the jam clear latch 5 then pull up to open the nosepiece door. 4. Remove bent nail, using pliers if necessary. 5. If driver blade is in the down position, cycle the stall release lever 12 using enough force to fully slide it to the other end of the slot in the housings. 12 NOTE: Should nails continue to jam frequently in nosepiece, have tool serviced by an authorized DeWALT service center. Cold Weather Operation When operating tools at temperatures below freezing: 1. Keep tool as warm as possible prior to use. 2. Actuate the tool 5 or 6 times into scrap lumber before using. Hot Weather Operation Tool should operate normally. However, keep tool out of direct sunlight as excessive heat can deteriorate bumpers and other rubber parts resulting in increased maintenance. MAINTENANCE WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
ENGLISH
12
Fig. H
3
13
Headlights (Fig. I)
There is a headlight 
 4 
located on each side of the nailer.
Headlights turn on upon battery insertion, activation of
the trigger, or depressing the contact trip. The lights will
automatically shut off after 20 seconds unless tool remains
in use.
Fig. I
4
NOTE:
These headlights are for lighting the immediate work
surface and are not intended to be used as flashlights.
LOW BATTERY INDICATOR:
The left-side headlight will
flash four consecutive times and then shut down to indicate
low battery.
JAMMED NAIL INDICATOR:
The right-side headlight will
flash continually if a nail becomes jammed in the nosepiece
(see
Clearing a Jammed Nail
).
Clearing a Jammed Nail (Fig. A, J)
If a nail becomes jammed in the nosepiece, keep the tool
pointed away from you and follow these instructions
to clear:
1. Remove battery pack from tool and engage the trigger
lock-off.
2. Press the magazine latch 
 16 
and remove any
loaded nails.
3. Lift the jam clear latch 
 5 
then pull up to open the
nosepiece door.
4. Remove bent nail, using pliers if necessary.
5. If driver blade is in the down position, cycle the stall
release lever 
 12 
using enough force to fully slide it to
the other end of the slot in the housings.
6. Close the nosepiece door and engage the latch pin
under the two arms on the nosepiece. Push latch until
it locks in place.
7. Reinsert battery pack.
NOTE:
The tool will disable itself and not reset until the
battery pack has been removed and reinserted.
8. Reinsert nails into magazine (see
Loading the Tool)
.
Fig. J
5
12
NOTE:
Should nails continue to jam frequently in nosepiece,
have tool serviced by an authorized
D
E
WALT
service center.
Cold Weather Operation
When operating tools at temperatures below freezing:
1. Keep tool as warm as possible prior to use.
2. Actuate the tool 5 or 6 times into scrap lumber
before using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of
direct sunlight as excessive heat can deteriorate bumpers
and other rubber parts resulting in increased maintenance.
MAINTENANCE
±
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start-up can cause injury.