Denon 1506 Owners Manual - Page 39

Last function memory

Get Denon 1506 - AVR AV Receiver PDF manuals and user guides
UPC - 081757506502
View all Denon 1506 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Advanced Operation 5 When the input source is set to TUNER, the preset channel can be selected pressing the CHANNEL button on the remote control unit. • The input source selected with the INPUT SELECTOR knob is output for the ZONE2 speaker output. INPUT SELECTOR POWER SPEAKER ENGLISH Advanced Operation Last function memory • This unit is equipped with a last function memory which stores the input and output setting conditions as they were immediately before the power is switched off. This function eliminates the need to perform complicated resettings when the power is switched on. • The unit is also equipped with a back-up memory. This function provides approximately one week of memory storage when the main unit's POWER switch is off and the power supply cord disconnected. Other functions Recording the program source (recording the source currently being monitored) 1 Select the input source to be played. 2 Select the input mode and play (surround) mode. 3 Start recording on the tape or video deck. For instructions, refer to the component's operating instructions. Initialization of the microprocessor If the indication on the display is not normal or if the operation of the unit is not correct, then the microprocessor should be reset by the following procedure. 1 Switch off the unit using the main unit's POWER switch. 2 Keep both SPEAKER A and B buttons depressed and turn on the unit by pressing the main unit's POWER switch. 3 Check that the entire display is flashing at 1second intervals and release the buttons. • The microprocessor will be initialized. • The AUDIO IN's signal selected with the INPUT SELECTOR knob are output to the CDR/TAPE and VCR AUDIO OUT terminals. 2 Simultaneous recording The signals of the source selected with the INPUT SELECTOR knob are output simultaneously to the CDR/TAPE and VCR REC OUT terminals. If a total of two tape and/or video decks are connected and set to the recording mode, the same source can be recorded simultaneously on every decks. • If step 3 does not work, start over from step 1. • If the microprocessor has been reset, all the button settings are reset to the default values (the values set upon shipment from the factory). 36 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
ENGLISH
36
Advanced Operation
Advanced Operation
ENGLISH
5
When the input source is set to TUNER, the
preset channel can be selected pressing the
CHANNEL
button on the remote control unit.
•
The input source selected with the
INPUT SELECTOR
knob is
output for the ZONE2 speaker output.
Initialization of the microprocessor
If the indication on the display is not normal or if the operation of
the unit is not correct, then the microprocessor should be reset
by the following procedure.
1
Switch off the unit using the main unit’s
POWER
switch.
2
Keep both
SPEAKER A
and
B
buttons depressed
and turn on the unit by pressing the main unit’s
POWER
switch.
3
Check that the entire display is flashing at 1-
second intervals and release the buttons.
•
The microprocessor will be initialized.
•
If step 3 does not work, start over from step 1.
•
If the microprocessor has been reset, all the button settings are
reset to the default values (the values set upon shipment from
the factory).
Other functions
Last function memory
•
This unit is equipped with a last function memory which stores
the input and output setting conditions as they were
immediately before the power is switched off.
This function eliminates the need to perform complicated
resettings when the power is switched on.
•
The unit is also equipped with a back-up memory. This function
provides approximately one week of memory storage when the
main unit
’
s
POWER
switch is off and the power supply cord
disconnected.
POWER
SPEAKER
INPUT SELECTOR
Recording the program source (recording the
source currently being monitored)
1
Select the input source to be played.
3
Start recording on the tape or video deck.
For instructions, refer to the component
’
s operating instructions.
2
Select the input mode and play (surround) mode.
•
The AUDIO IN
’
s signal selected with the
INPUT SELECTOR
knob
are output to the CDR/TAPE and VCR AUDIO OUT terminals.
2
Simultaneous recording
The signals of the source selected with the
INPUT SELECTOR
knob
are output simultaneously to the CDR/TAPE and VCR REC OUT
terminals. If a total of two tape and/or video decks are connected
and set to the recording mode, the same source can be recorded
simultaneously on every decks.