Dell Inspiron 27 7730 All-in-One Owners Manual - Page 60

Installing the retractable-camera assembly, Steps, Prerequisites, About this task, Next steps

Get Dell Inspiron 27 7730 All-in-One PDF manuals and user guides View all Dell Inspiron 27 7730 All-in-One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Steps 1. Disconnect the camera cable from its connector (WEBCAM) on the system board. 2. Peel the tape that secures the camera cable to the display-assembly base. 3. Remove the two screws (M3x5) that secure the retractable-camera assembly to the display-assembly base. 4. Remove the retractable-camera assembly from the display-assembly base. Installing the retractable-camera assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the retractable-camera assembly and provides a visual representation of the installation procedure. Figure 35. Installing the camera Steps 1. Slide and place the retractable-camera assembly on the display-assembly base. 2. Replace the two screws (M3x5) that secure the retractable-camera assembly to the display-assembly base. 3. Adhere the tape that secures the camera cable to the display-assembly base. 4. Connect the camera cable to its connector (WEBCAM) on the system board. Next steps 1. Install the system-board shield. 60 Removing and installing Customer Replaceable Units (CRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
Steps
1.
Disconnect the camera cable from its connector (WEBCAM) on the system board.
2.
Peel the tape that secures the camera cable to the display-assembly base.
3.
Remove the two screws (M3x5) that secure the retractable-camera assembly to the display-assembly base.
4.
Remove the retractable-camera assembly from the display-assembly base.
Installing the retractable-camera assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the retractable-camera assembly and provides a visual representation of the
installation procedure.
Figure 35. Installing the camera
Steps
1.
Slide and place the retractable-camera assembly on the display-assembly base.
2.
Replace the two screws (M3x5) that secure the retractable-camera assembly to the display-assembly base.
3.
Adhere the tape that secures the camera cable to the display-assembly base.
4.
Connect the camera cable to its connector (WEBCAM) on the system board.
Next steps
1.
Install the
system-board shield
.
60
Removing and installing Customer Replaceable Units (CRUs)