Boss Audio CXX2502 User Manual in English - Page 10
Troubleshooting, Specifications, MODEL
View all Boss Audio CXX2502 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. SYMPTOM Amplifier will not power up. Protection LED comes on when amplifier is powered up. No output. Low output. Audio present in only one channel. High hiss in the speakers. Squealing noise from speakers. POSSIBLE REMEDY Check to make sure you have a good ground connection. Check that the Remote Input (Turn-On) has at least 3VDC. Check that there is battery power on the (+) terminal. Check that there is at least 12v. Check all fuses, replace ifnecessary. Make sure that the Protection LED is not illuminated. Ifit is lit, shut off the amplifier briefly, and then repower it. Check for short circuits on speaker leads. Turn down the volume control on the head unit to prevent overdriving. Remove speaker leads, and reset the amplifier If the Protection LED still comes on, then the amplifier is faulty and needs servicing. Check that all fuses are OK. Check that amplifier is properly grounded. Check that the Remote Input (Turn-On) has at least 3VDC. Check that the RCA audio cables are plugged into the proper inputs. Check all speaker wiring. Reset the Level Control. Check the Crossover Control settings. Check the RCA interconnect cables. Check all speaker wiring. Disconnect allRCA inputs to the amplifiers. If the hiss disappears, then plug in the component driving the amplifier and unplug its inputs. If the hiss disappears at this point, go on until the faulty/noisy component is found. It is best to set the amplifier's input level control as low as possible. The best subjective signal-to-noise ratio is achieved in this manner. Try to set the head unit as high as possible (without distortion) and the amp input level as low as possible. Check for improperly grounded RCA interconnects. Distorted sound. Amplifier gets very hot. Engine noise (static type) Engine noise (alternator whine) Check that the Input Level Control is set to match the signal level of the head unit. Always try to set the Input Level as low as possible. Check that all crossover frequencies are properly set. Check for short circuits on the speaker leads. Check that the minimum speakerimpedance for the amp modelis correct Check that there is good air circulation around the amp. In some applications, it may be necessary to add external cooling fan(s). This is usually causedbypoor quality RCA cables,which can pick up radiated noise. Use only the best qualify cables, and route them away from power cables. Check that speaker leads are not shorted to the vehicle chassis. Check that the RCA grounds are not shorted to the vehicle chassis. Check that the head unit is properly grounded. CHAOS EXXTREME II MOSFET Amplifier User's Manual - page 16 Specifications 3ObS AUDIO SYSTEMS MODEL 2-Channel MOSFET Amplifiers CXX5O2 CXX1OO2 CXXl602 CXX2OO2 CXX25O2 RMS Power Into 40 MAX Power into 20 Bridged Power Into 4 O Min. Speaker Impedance 100Wx2 175Wx2 250Wx 2 500Wx 2 500Wx1 1000Wx1 2O Stereo 4O Mono Bridged THD+N '• 0.01% Frequency Response 9Hz- 50 KHz S/N Ratio 103dB Channel Separation 90dB Low Pass Filter 35 Hz-160Hz High Pass Filter Fixed, 80 Hz Bass Boost Fuse Rating Variable 0 - +18dB 30A 40A Dimensions (Length) : 8.27"(-) (W x H)(11.00" x 2.87") 12.20"(I) 240 Wx 2 300Wx2 800 Wx 2 1000 Wx2 1600Wx1 2000 Wx1 25Ax2 13.78" (I-) 30Ax2 15.75"04 500 Wx2 1250Wx2 2500 Wx1 40Ax2 19.69"(L) MODEL 4-Channel MOSFET Amplifiers 5-Channel MOSFET Amplifier MonoBlock MOSFET Amplifiers ClO(1204 CXX1604 CXX2004 C)0(2404 CXX2705 CXXIA1250 CXXM1800 CXXM2200 RMS Power Into 4 0 MAX Power Into 20 Bridged Power into 40 100 Wx4 150Wx4 200Wx4 300Wx4 150Wx4+ 500Wx1 600 Wx 1 300W x 4 400Wx 4 500Wx4 600Wx 4 450 Wx4 + 1250W x1 900 W x 1 600W x 2 800Wx 2 1000Wx 2 1200 W x 2 600 W x 2 + n/a 900Wx1 700Wx1 900Wx1 1800Wx 1 2200 W x1 n/a n/a Min. Speaker Impedance 20 Stereo 40 Mono Brhlged 20 20 20 THD + N 0.01% Frequency Response g Hz-50 KHz 9Hz-130Hz 9Hz-130Hz SIN Ratio 103dB Ch I Separation 90dB n/a n/a n/a Low Pass Filte► 35 Hz -160 Hz High Pass Filter Fixed, 80Hz Bass Boost Variable 0 - +18dB Switchable 0 / + 18 dB 0 / +18 dB Input Mode Selector n/a n/a n/a n/a 4CH/5CH Fuse Rating 25Ax2 30Ax2 35Ax 2 30Ax3 30A x 3 Dimensions (Length) : 12.99" (-) 13.78"(-) 16.93"(-) 23.23"(L) 20.28" (L) (Vixli)(11.00- x2.87") 40 Hz -130 Hz 40 Hz -130 Hz n/a n/a n/a 0 - +12dB 0 - +12dB 0/+18dB n/a n/a n/a 30A 25Ax2 30Ax2 10.63"(L) 13.78"(L) 16.93"(L) All specifications subject to change without notice. CHAOS EXXTREME II MOSFET Amplifier User's Manual - page 17