BenQ TK850 User Manual - Page 21

Switching input signal, Disabling the password function

Get BenQ TK850 PDF manuals and user guides View all BenQ TK850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

3. Enter the old password. • If the password is correct, another message "Input New Password" appears. • If the password is incorrect, the password error message will appear, and the message "Input Current Password" appears for your retry. You can press BACK to cancel the change or try another password. 4. Enter a new password. 5. Confirm the new password by re-entering the new password. Disabling the password function To disable password protection, go to SYSTEM SETUP: ADVANCED Menu > Password > Power On Lock and press / to select Off. The message "Input Current Password" appears. Enter the current password. • If the password is correct, the OSD menu returns to the password setting page. You will not have to enter the password next time turning on the projector. • If the password is incorrect, the password error message will appear, and the message "Input Current Password" appears for your retry. You can press BACK to cancel the change or try another password. Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password. Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals. Be sure the SYSTEM SETUP: BASIC Menu > Auto Source menu is On if you want the projector to automatically search for the signals. To select the source: 1. Press SOURCE. A source selection bar appears. 2. Press / until your desired signal is selected and press OK. Once detected, the selected source information will appear at the corner of the screen for seconds. If there is multiple equipment connected to the projector, repeat steps 1-2 to search for another signal. • The brightness level of the projected image will change accordingly when you switch between different input signals. • For best display picture results, you should select and use an input signal which outputs at the projector's native resolution. Any other resolutions will be scaled by the projector depending upon the "aspect ratio" setting, which may cause some image distortion or loss of picture clarity. See Aspect Ratio on page 28. Operation 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
21
Operation
3.
Enter the old password.
• If the password is correct, another message
“Input New Password”
appears.
• If the password is incorrect, the password error message will appear, and the message
“Input
Current Password”
appears for your retry. You can press
BACK
to cancel the change or try
another password.
4.
Enter a new password.
5.
Confirm the new password by re-entering the new password.
Disabling the password function
To disable password protection, go to
SYSTEM SETUP: ADVANCED Menu
>
Password >
Power On Lock
and press
/
to select
Off.
The message
“Input Current Password”
appears.
Enter the current password.
• If the password is correct, the OSD menu returns to the password setting page. You will not have
to enter the password next time turning on the projector.
• If the password is incorrect, the password error message will appear, and the message
“Input
Current Password”
appears for your retry. You can press
BACK
to cancel the change or try
another password.
Switching input signal
The projector can be connected to multiple devices at the same time.
However, it can only display one full screen at a time. When starting up, the
projector automatically searches for the available signals.
Be sure the
SYSTEM SETUP: BASIC Menu
>
Auto Source
menu is
On
if you want the projector to automatically search for the signals.
To select the source:
1.
Press
SOURCE
. A source selection bar appears.
2.
Press
/
until your desired signal is selected and press
OK
.
Once detected, the selected source information will appear at the corner of the screen for seconds.
If there is multiple equipment connected to the projector, repeat steps 1-2 to search for another
signal.
Though the password function is disabled, you need to keep the old password in hand should you ever need to
re-activate the password function by entering the old password.
• The brightness level of the projected image will change accordingly when you switch between different input
signals.
• For best display picture results, you should select and use an input signal which outputs at the projector’s native
resolution. Any other resolutions will be scaled by the projector depending upon the "aspect ratio" setting, which
may cause some image distortion or loss of picture clarity. See
Aspect Ratio on page 28
.