BenQ BenQ PU9530 Large Venue Projector User Manual - Page 46

Standby Settings, Standard, Network, High Altitude, Auto Power Off, RS232, Baud Rate

Get BenQ BenQ PU9530 Large Venue Projector PDF manuals and user guides View all BenQ BenQ PU9530 Large Venue Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

English Standby Settings Press ◄► arrow key to toggle switch between Standard, Eco and Network mode. Standard:The projector can be turned on using the remote control, RS-232 command or network control. Eco:The projector maintains in the standby status at the lowest power (

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
English
46
Standby Settings
Press
◄►
arrow key to toggle switch between
Standard
,
Eco
and
Network
mode.
Standard
: The projector can be turned on using the remote control, RS-232 command or
network control.
Eco
: The projector maintains in the standby status at the lowest power (<0.5W). In this mode,
the projector can be turned on only using the power button on the remote controller or
projector.
Network
: The projector maintains in the standby status at the power consumption under
6W, the projector can be turned on using the power button or network control only, RS-232
control command and wired remote control signal via external transmitter through RJ45 cable
are not available.
Some of communication ports are turned off if it's set to
Eco
or
Network
mode, please make sure that the Standby
Settings is set to proper setting.
High Altitude
You can use this function to turn the option to
On
for switching the cooling setting if the
project is installed in a high altitude environment, the default is
Off
.
The projector may turn off automatically if it is used in an environment at excessively high
temperature or in an area at a high altitude. In this case, you can enable this function by setting
it to
On
and have the cooling fan operate at a higher speed to low the internal temperature of
the projector.
An area is considered high altitude when it is above 5000 feet.
Auto Power Off
This function enables the projector to enter standby mode automatically when no input signal
is detected more than 15 minutes. Set the function to
On
to enable
Auto Power off
or to
Off
to disable it.
Auto Power On
This function enables the projector to be turned on automatically when the power cord is
plugged into the AC outlet or the breaker switch is turned. Set the function to
On
to enable
this function.
This function is activated by below conditions
•
The Main Power switch on the projector has to be switched to On.
•
The projector should be turned off by unplugging power cord or the breaker switch
directly,
Auto Power On
will be activated next time when you plug in the power cord or
turn on breaker switch.
RS232
Baud Rate
: Set transmission speed to:
115200
,
57600
,
38400
,
19200
,
14400
, and
9600
.
Transmission speed shall vary with length of RS-232 cable (longer cable requires slower
speed). In case of unstable signal or connection failure when controlling with RS-232 cable, try
downgrading the transmission speed.