BenQ BenQ MX810ST Short-Throw Interactive Wireless Projector MX812ST User Manu - Page 40

Controlling the projector through a LAN environment, Cable connection

Get BenQ BenQ MX810ST Short-Throw Interactive Wireless Projector PDF manuals and user guides View all BenQ BenQ MX810ST Short-Throw Interactive Wireless Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Controlling the projector through a LAN environment You can manage and control the projector from one or more remote computers when they are properly connected to the same local area network. Cable/ADSL Internet modem Cable connection If you are in a DHCP environment: 1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port on your Ethernet or router. 2. Do one of the following: • Press NETWORK SETTING on the remote control. The Network Settings page is displayed. • Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted. Press to highlight Network Settings and press MODE/ ENTER. The Network Settings page is displayed. 3. Highlight Wired LAN and press MODE/ENTER. 4. Make sure the Status is Connect. 5. Press to highlight DHCP and press / to select On. 6. Press to highlight Apply and press MODE/ENTER. 7. Re-enter the Network Settings > Wired LAN page. The IP Address, Subnet Mask, Default Gateway, and DNS settings will be displayed. Note down the IP address displayed in the IP Address row. If the IP Address still does not appear, contact your ITS administrator. If you are in a non-DHCP environment: 1. Repeat steps 1-4 above. 2. Press to highlight DHCP and press / to select Off. 3. Contact your ITS administrator for information on the IP Address, Subnet Mask, Default Gateway, and DNS settings. 4. Press to select the item you want to modify and press MODE/ENTER. 5. Press / to move the cursor and the press / to enter the value. 6. To save the settings, press MODE/ENTER. If you do not want to save the settings, press MENU/EXIT. 7. Press to highlight Apply and press MODE/ENTER. 40 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
Operation
40
Controlling the projector through a LAN
environment
You can manage and control the projector from one or more remote computers when they
are properly connected to the same local area network.
Cable connection
If you are in a DHCP environment:
1.
Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector
and the other end to the RJ45 port on your Ethernet or router.
2.
Do one of the following:
•
Press
NETWORK SETTING
on the remote control. The
Network Settings
page
is displayed.
•
Press
MENU/EXIT
and then press
/
until the
SYSTEM SETUP: Advanced
menu is highlighted. Press
to highlight
Network Settings
and press
MODE/
ENTER
. The
Network Settings
page is displayed.
3.
Highlight
Wired LAN
and press
MODE/ENTER
.
4.
Make sure the
Status
is
Connect
.
5.
Press
to highlight
DHCP
and press
/
to select
On
.
6.
Press
to highlight
Apply
and press
MODE/ENTER
.
7.
Re-enter the
Network Settings
>
Wired LAN
page. The
IP Address
,
Subnet Mask
,
Default Gateway
, and
DNS
settings will be displayed. Note down the IP address
displayed in the
IP Address
row.
If the IP Address still does not appear, contact your ITS administrator.
If you are in a non-DHCP environment:
1.
Repeat steps 1-4 above.
2.
Press
to highlight
DHCP
and press
/
to select
Off
.
3.
Contact your ITS administrator for information on the
IP Address
,
Subnet Mask
,
Default Gateway
, and
DNS
settings.
4.
Press
to select the item you want to modify and press
MODE/ENTER
.
5.
Press
/
to move the cursor and the press
/
to enter the value.
6.
To save the settings, press
MODE/ENTER
. If you do not want to save the settings,
press
MENU/EXIT
.
7.
Press
to highlight
Apply
and press
MODE/ENTER
.
Cable/ADSL
modem
Internet