ASRock Vision 3D 241B Quick Installation Guide - Page 2
Opening the chassis, Reinstalling the ODD/HDD, Reinstalling the DIMMs, Reinstalling the CPU,
View all ASRock Vision 3D 241B manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Opening the chassis 1. Press the button on the rear I/O to open the top side of the chassis. 2. After the chassis is opened, you will see the top shield inside the chassis. 3. Unscrew the screws on the corner of the top shield. 4. Carefully take the top shield out. Reinstalling the ODD/HDD Reinstalling the DIMMs Reinstalling the MXM card Safety instructions 1. After you remove the top shield, you will see the ODD/HDD bracket. 1. Unlock the DIMM slot by pressing the retaining clips outward to change the DIMM. 2. Disconnect the ODD/HDD SATA power cable, and take out the ODD/HDD bracket. Reinstalling the CPU 1. Unscrew the screws of the CPU fan. 3. Disconnect all the ODD/HDD SATA power cables inside the chassis. 2. Unscrew the screws on the corner of the CPU socket. 4. Then you can change the new ODD/HDD to upgrade your system. 3. Now you can reinstall a new CPU to the system. 1. Unscrew the screws of the heatpipe on the MXM card. 2. Use your fingers to pull the outer side of the heatpipe upward. 3. Finally you can take out the heatpipe and change a new MXM card. Your system is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system • Read and follow all instructions in the documentation before you operate your system. • Do not use this product near water or a heated source such as a radiator. • Set up the system on a stable surface. • Openings on the chassis are for ventilation. Do not block or cover these openings. Make sure you leave plenty of space around the system for ventilation. Never insert objects of any kind into the ventilation openings. • Use this product in environments with ambient temperatures between 0˚C and 40˚C. • If you use an extension cord, make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating. Care during use • Do not walk on the power cord or allow anything to rest on it. • Do not spill water or any other liquids on your system. • When the system is turned OFF, a small amount of electrical current still flows. Always unplug all power, modem, and network cables from the power outlets before cleaning the system. • If you encounter the following technical problems with the product, unplug the power cord and contact a qualified service technician or your retailer. • The power cord or plug is damaged. • Liquid has been spilled into the system. • The system does not function properly even if you follow the operating instructions. • The system was dropped or the cabinet is damaged. • The system performance changes. NOTE: The warranty does not apply to products that have been disassembled by users. Safety cautions and warnings Optical Drive Safety Information Optical drives sold with this system contains a CLASS 1 LASER PRODUCT. CAUTION: Invisible laser radiation when open. Do not stare into beam or view directly with optical instruments. WARNING: Making adjustments or performing procedures other than those specified in the user's manual may result in hazardous laser exposure. Do not attempt to disassemble the optical drive. For your safety, have the optical drive serviced only by an authorized service provider. Product disposal notice IMPORTANT: This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products. Nordic Lithium Cautions (for lithium-ion batteries) CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. English Opening the chassis 1. Press the button on the rear I/O to pen the top side of the chassis. 2. After the chassis is opened, you will see the top shield inside the chassis. 3. Unscrew the screws on the corner of the top shield. 4. Carefully take the top shield out. Reinstalling the ODD/HDD 1. After you remove the top shield, you will see the ODD/HDD bracket. 2. Disconnect the ODD/HDD SATA power cable, and take out the ODD/HDD bracket. 3. Disconnect all the ODD/HDD SATA power cables inside the chassis. 4. Then you can change the new ODD/HDD to upgrade your system. Reinstalling the DIMMs 1. Unlock the DIMM slot by pressing the retaining clips outward to change the DIMM. Reinstalling the CPU 1. Unscrew the screws of the CPU fan. 2. Unscrew the screws on the corner of the CPU socket. 3. Now you can reinstall a new CPU to the system. Reinstalling the MXM card 1. Unscrew the screws of the heatpipe on the MXM card. 2. Use your fingers to pull the outer side of the heatpipe upward. 3. Finally you can take out the heatpipe and change a new MXM card. 繁體中文 1.按後面I/O 2 3 4 1 2 SATA 3 SATA Cable線。 4 重新安裝DIMM 1 重新安裝CPU 1. 擰開CPU 2. 擰開CPU 3 CPU到系統。 重新安裝MXM顯示卡 1.. 擰開MXM 2 MXM 3 MXM顯示卡。 Español Apertura del chasis 1. Pulse el botón situado en el panel posterior de E/S para abrir la parte superior del chasis. 2. Una vez abierto el chasis, podrá ver la cubierta protectora superior en su interior. 3. Desenrosque los tornillos situados en las esquinas de la cubierta protectora superior. 4. Extraiga la cubierta protectora superior con cuidado. Sustitución de la unidad ODD/HDD 1. Una vez extraída la cubierta protectora superior, podrá ver la abrazadera de la unidad ODD/HDD. 2. Desconecte el cable de alimentación SATA de la unidad ODD/HDD instalada y extraiga la abrazadera de la unidad ODD/HDD. 3. Desconecte todos los cables de alimentación SATA de las unidades ODD/HDD instaladas en el interior del chasis. 4. A continuación, instale la nueva unidad ODD/HDD para actualizar el sistema. Sustitución de los módulos DIMM 1. Desbloquee una ranura DIMM presionando las pinzas de retención hacia fuera y sustituya el módulo DIMM correspondiente. Sustitución de la CPU 1. Desenrosque los tornillos del ventilador de la CPU. 2. Desenrosque los tornillos situados en las esquinas del zócalo de la CPU. 3. Ahora podrá instalar una nueva CPU en el sistema. Sustitución de la tarjeta MXM 1. Desenrosque los tornillos que mantienen sujeto el tubo de disipación de la tarjeta MXM. 2. Extraiga la parte externa del tubo de disipación tirando de ella hacia arriba con los dedos. 3. Por último, extraiga el tubo de disipación y sustituya la tarjeta MXM por una nueva. 1 2 3 4 1 2 SATA 3 SATA 4 DIMM 1 DIMM DIMM. 1 2 3 MXM-карты 1 MXM 2 3 MXM-карту. Deutsch Gehäuse öffnen 1. Drücken Sie zum Öffnen der oberen Gehäuseblende die Taste am hinteren E/A. 2. Nachdem das Gehäuse geöffnet ist, sehen Sie die obere Abdeckung im Inneren des Gehäuses. 3. Lösen Sie die Schrauben in den Ecken der oberen Abdeckung. 4. Nehmen Sie die obere Abdeckung vorsichtig heraus. Neue ODD/HDD installieren 1. Nachdem Sie die obere Abdeckung entfernt haben, sehen Sie die ODD-/HDD-Halterung. 2. Ziehen Sie das ODD-/HDD-SATA-Netzkabel; nehmen Sie die ODD-/HDD-Halterung heraus. 3. Ziehen Sie alle ODD-/HDD-SATA-Netzkabel im Inneren des Gehäuses. 4. Anschließend können Sie das neue ODD/die neue HDD zum Aufrufen Ihres Systems einbauen. Neue DIMMs installieren 1. Lösen Sie den DIMM-Steckplatz, indem Sie die Halteklammern zum Auswechseln des DIMM nach außen drücken. Neue CPU installieren 1. Lösen Sie die Schrauben des CPU-Kühlers. 2. Lösen Sie die Schrauben in den Ecken des CPU-Sockels. 3. Nun können Sie eine neue CPU im System installieren. Neue MXM-Karte installieren 1. Lösen Sie die Schrauben vom Wärmerohr der MXM-Karte. 2. Ziehen Sie die Außenseite des Wärmerohrs mit Ihren Fingern nach oben. 3. Nehmen Sie das Wärmerohr schließlich heraus; setzen Sie eine neue MXM-Karte ein. Français Ouverture du châssis 1. Appuyez sur le bouton sur la panneau E/S arrière pour ouvrir la face supérieure du châssis. 2. Une fois que le châssis est ouvert, vous pouvez voir la plaque de protection supérieure dans le châssis. 3. Dévissez les vis sur le coin de la plaque de protection supérieure. 4. Sortez soigneusement la plaque de protection supérieure. Réinstallation de l'unité optique/du disque dur 1. Après avoir retiré la plaque de protection supérieure, vous pouvez voir le suppport pour unité optique/disque dur. 2. Débranchez le câble d'alimentation SATA pour unité optique/disque dur, et sortez le support pour unité optique/disque dur. 3. Débranchez tous les câbes d'alimentation SATA pour unité optique/disque dur qui se trouvent à l'intérieur du châssis. 4. Vous pouvez alors changer l'unité optique ou le disque dur pour mettre votre système à niveau. Réinstallation des modules DIMM 1. Déverrouillez l'emplacement pour module DIMM en appuyant sur les clips de fixation de façon à les écarter vers l'extérieur pour changer le module DIMM. Réinstallation du processeur 1. Dévissez les vis du ventilateur du processeur. 2. Dévissez les vis sur le coin du socle du processeur. 3. Vous pouvez maintenant installer le nouveau processeur dans le système. Réinstallation de la carte MXM 1. Dévissez les vis sur le caloduc de la carte MXM. 2. Servez-vous de vos doigts pour soulever l'extrémité extérieure du caloduc. 3. Vous pouvez enfin retirer le caloduc et mettre en place une nouvelle carte MXM. Italiano Apertura del telaio 1. Premere il tasto sul pannello I/O posteriore per aprire la parte superiore del telaio. 2. Dopo avere aperto il telaio, si vedrà la protezione superiore all'interno. 3. Togliere le viti sugli angoli della protezione superiore. 4. Estrarre delicatamente la protezione superiore. Installazione dell'unità ODD/HDD 1. Dopo avere rimosso la protezione superiore si vedrà il supporto ODD/HDD. 2. Scollegare il cavo d'alimentazione ODD/HDD SATA ed estrarre il supporto ODD/HDD. 3. Scollegare tutti i cavi d'alimentazione ODD/HDD SATA all'interno del telaio. 4. Poi si può installare la nuova unità ODD/HDD per aggiornare il sistema. Installazione dei moduli DIMM 1. Sbloccare l'alloggio DIMM premendo verso l'esterno i fermagli ed installare il modulo DIMM. Installazione della CPU 1. Togliere le viti della ventola CPU. 2. Togliere le viti sugli angoli del socket CPU. 3. Adesso si può installare la nuova CPU sul sistema. Installazione della scheda MXM 1. Togliere le viti del tubo termovettore (heatpipe) della scheda MXM. 2. Con le dita sollevare l'estremità del tubo termovettore. 3. Infine, estrarre il tubo termovettore ed installare la nuova scheda MXM. Português Abrir o chassis 1. Prima o botão E/S na traseira para abrir a parte superior do chassis. 2. Depois de abrir o chassis, irá ver a protecção superior no interior do chassis. 3. Desaperte os parafusos no canto da protecção superior. 4. Remova a protecção superior com cuidado. Reinstalar a Unidade de Disco Óptico/Disco Rígido 1. Depois de remover a protecção superior, irá ver o suporte da Unidade de Disco Óptico/Disco Rígido. 2. Desligue o cabo de alimentação SATA da Unidade de Disco Óptico/Disco Rígido e retire o suporte da Unidade de Disco Óptico/Disco Rígido. 3. Desligue todos os cabos de alimentação SATA da Unidade de Disco Óptico/Disco Rígido no interior do chassis. 4. Pode agora trocar a Unidade de Disco Óptico/Disco Rígido para actualizar o seu sistema. Reinstalar os módulos DIMM 1. Abra a ranhura DIMM pressionando para fora os clipes de retenção para trocar o módulo DIMM. Reinstalar a CPU 1. Desaperte os parafusos da ventoinha da CPU. 2. Desaperte os parafusos no canto do suporte da CPU. 3. Pode agora instalar uma nova CPU no seu sistema. Reinstalar a placa MXM 1. Desaperte os parafusos do dissipador de calor da placa MXM. 2. Utilize os dedos para puxar para cima a parte exterior do dissipador de calor. 3. Por fim, pode remover o dissipador de calor e trocar a placa MXM. 1. 뒷면 I/O 2 3 4 ODD/HDD 1 ODD/HDD 2. ODD/HDD SATA ODD/HDD 3 ODD/HDD SATA 4. 이제 ODD/HDD DIMM 1 DIMM DIMM을 CPU 1. CPU 2. CPU 3 CPU MXM 1. MXM 2 3 MXM 1. 背面I/O 2 3 4 ODD/HDDの交換 1 ODD/HDD 2. ODD/HDD SATA ODD/HDD 3 ODD/HDD SATA 4 ODD/HDD DIMMの交換 1. DIMM DIMM CPUの交換 1. CPU 2. CPU 3 CPU MXM 1. MXM 2 3 MXM