3M MP8765 Operating Guide - Page 22

TROUBLESHOOTING, Service Infomation, OSD Message

Get 3M MP8765 PDF manuals and user guides View all 3M MP8765 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

3M™ Multimedia Projector 8765 TROUBLESHOOTING Service Infomation For product infomation,product assistance,service infomation,or to order accessories,please call: In U.S.or Canada :1-800-328-1371 In other locations,contact your local 3M sales office. OSD Message The messages as described below may appear on the screen at power ON. Take the appropriate measures when such messages appears. Table 9. OSD Message Message Contents CHANGE THE LAMP The usage time of lamp will be reaching 2000 hr AFTER REPLACING LAMP, shortly.(*2) RESET THE LAMP TIME. It is recommended to replace the lamp soon. Prepare a (*1) new lamp as a replacement. The usage time of lamp will be reaching 2000 hr shortly. CHANGE THE LAMP It is recommended to replace the lamp within * * AFTER REPLACING LAMP, hours.(*2) RESET THE LAMP TIME. It might be happened that the lamp is cut off before * * hr THE POWER WILL TURN OFF by any chance. Power will be switched OFF AFTER ** hr. automatically in * * hours. Replace the lamp as shown in (*1) P.17~18 "Lamp". Always reset the lamp timer after replacing the lamp. CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIME. THE POWER WILL TURN OFF AFTER 0 hr. The usage time of lamp is about to reach. Power will be switched OFF in a few minutes.(*2) Switch power OFF immediately and replace the lamp as shown in P.17 ~18 "Lamp". Always reset the lamp timer after replacing the lamp. NO INPUT IS DETECTED ON *** No input signal found. Check signal input connections and signal sources. SYNC IS OUT OF RANGE ON *** The horizontal or vertical frequency of the input signal is not within the specified range. Check the specifications of the equipment and the signal source. NOTE (*1) This message is cleared automatically after approximately three minutes, and appears every time power is switched ON. (*2) The unit has a function to turn the power off which will be active when the usage time reaches 2000 hr. However the life of lamp might be much different among lamps, so that it might be happened that a lamp is cut off before the function is active. ENGLISH-20 © 3M 2002. All Rights Reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
ENGLISH-20
ENGLISH-20
TROUBLESHOOTING
TROUBLESHOOTING
Service Infomation
For product infomation,product assistance,service infomation,or to order accessories,please call:
In U.S.or Canada :1-800-328-1371
In other locations,contact your local 3M sales office.
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate
measures when such messages appears.
Table 9. OSD Message
Message
Contents
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
(
*
1)
The usage time of lamp will be reaching 2000 hr
shortly.
(*2)
It is recommended to replace the lamp soon.
Prepare a
new lamp as a replacement.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN OFF
AFTER
**
hr.
(
*
1)
The usage time of lamp will be reaching 2000 hr shortly.
It is recommended to replace the lamp within * *
hours.
(*2)
It might be happened that the lamp is cut off before * * hr
by any chance.
Power will be switched OFF
automatically in * * hours.
Replace the lamp as shown in
P.17~18
“
Lamp
”
.
Always reset the lamp timer after
replacing the lamp.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL
TURN OFF
AFTER 0 hr.
The usage time of lamp is about to reach.
Power will be
switched OFF in a few minutes.
(*2)
Switch power OFF immediately and replace the lamp as
shown in P.17 ~18
“
Lamp
”
.
Always reset the lamp timer
after replacing the lamp.
NO INPUT IS DETECTED
ON
***
No input signal found.
Check signal input connections and signal sources.
SYNC IS OUT OF RANGE
ON
***
The horizontal or vertical frequency of the input signal is
not within the specified range.
Check the specifications of the equipment and the signal
source.
(*1) This message is cleared automatically after approximately three minutes, and
appears every time power is switched ON.
(*2) The unit has a function to turn the power off which will be active when the usage time reaches
2000 hr.
However the life of lamp might be much different among lamps, so that it might be
happened that a lamp is cut off before the function is active.
NOTE
3M™ Multimedia Projector 8765
© 3M 2002.
All Rights Reserved.