2009 Yamaha Motorsports RS Vector L-TX Owners Manual - Page 57

2009 Yamaha Motorsports RS Vector L-TX Manual

Get 2009 Yamaha Motorsports RS Vector L-TX PDF manuals and user guides View all 2009 Yamaha Motorsports RS Vector L-TX manuals

Page 57 highlights

Periodic maintenance and adjustment 2. Rotate the secondary sliding sheave clockwise and push it so that it separates from the secondary fixed sheave. 1. Secondary sliding sheave 2. Secondary fixed sheave 3. Pull the V-belt up over the secondary fixed sheave. 1. Edge of the secondary sheave assembly 2. Spacer 3. V-belt position adjusting bolt ECS00510 NOTICE As the V-belt wears, adjustment may be necessary. To ensure proper clutch performance, the V-belt position should be adjusted by adding a spacer on each adjusting bolt when the V-belt position reaches 1.5 mm (0.06 in) below the edge of the secondary sheave assembly. Have a Yamaha dealer make this adjustment. 1. V-belt 4. 5. TIP Apply the parking brake before replacing the V-belt. 1. Remove the shroud and the left side cover, and then remove the drive guard. (See page 38 for removal procedures.) Remove the V-belt from the secondary sheave assembly and primary sheave assembly. Temporarily install the new V-belt on the secondary sheave assembly only, and then measure the V-belt position. Do not force the V-belt between the sheaves; the secondary sliding and fixed sheaves must touch each other. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Periodic maintenance and adjustment
51
NOTICE
ECS00510
As the V-belt wears, adjustment may be
necessary. To ensure proper clutch per-
formance, the V-belt position should be
adjusted by adding a spacer on each ad-
justing bolt when the V-belt position
reaches 1.5 mm (0.06 in) below the edge of
the secondary sheave assembly.
Have a Yamaha dealer make this adjust-
ment.
TIP
Apply the parking brake before replacing the
V-belt.
1.
Remove the shroud and the left side cov-
er, and then remove the drive guard.
(See page 38 for removal procedures.)
2.
Rotate the secondary sliding sheave
clockwise and push it so that it separates
from the secondary fixed sheave.
3.
Pull the V-belt up over the secondary
fixed sheave.
4.
Remove the V-belt from the secondary
sheave assembly and primary sheave
assembly.
5.
Temporarily install the new V-belt on the
secondary sheave assembly only, and
then measure the V-belt position. Do not
force the V-belt between the sheaves; the
secondary sliding and fixed sheaves
must touch each other.
1.
Edge of the secondary sheave assembly
2. Spacer
3.
V-belt position adjusting bolt
1.
Secondary sliding sheave
2.
Secondary fixed sheave
1. V-belt