2007 Yamaha Motorsports V Star Custom Owners Manual - Page 80

2007 Yamaha Motorsports V Star Custom Manual

Get 2007 Yamaha Motorsports V Star Custom PDF manuals and user guides View all 2007 Yamaha Motorsports V Star Custom manuals

Page 80 highlights

PERIODIC MAINTENANCE AND MINOR REPAIR EAU25511 To install the rear wheel 1. Install the rear wheel, wheel axle, final gear case, and drive shaft by pushing the wheel forward and guiding the drive shaft into the middle gear universal joint. 7. Tighten the axle nut, the final gear case bolts and the brake torque rod nuts to the specified torques. Tightening torques: Axle nut: 92 Nm (9.2 m·kgf, 67 ft·lbf) Final gear case bolt: 74 Nm (7.4 m·kgf, 54 ft·lbf) Brake torque rod nut: 20 Nm (2.0 m·kgf, 14 ft·lbf) 1. Bolt 2. Final gear case 6 7. Lift the rear wheel off the ground according to the procedure on page 6-34. 8. While supporting the drive shaft, pull the rear wheel back to remove the following parts as an assembly: wheel, wheel axle, final gear case, and drive shaft. NOTE: Make sure to support the drive shaft as it is being pulled out. 8. Adjust the brake pedal free play. (See page 6-23.) EWA10660 WARNING 1. Middle gear universal joint 2. Drive shaft After adjusting the brake pedal free play, check the operation of the brake light. 2. Install the final gear case bolts. 3. Install the brake rod onto the brake camshaft lever, and then install the brake pedal free play adjusting nut onto the brake rod. 4. Install the brake torque rod bolt and nut at the brake shoe plate. 5. Install the panel. 6. Lower the rear wheel so that it is on the ground. 6-37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
PERIODIC MAINTENANCE AND MINOR REPAIR
6-37
6
7. Lift the rear wheel off the ground
according to the procedure on
page 6-34.
8. While supporting the drive shaft,
pull the rear wheel back to remove
the following parts as an assem-
bly: wheel, wheel axle, final gear
case, and drive shaft.
NOTE:
Make sure to support the drive shaft as
it is being pulled out.
EAU25511
To install the rear wheel
1.
Install the rear wheel, wheel axle,
final gear case, and drive shaft by
pushing the wheel forward and
guiding the drive shaft into the mid-
dle gear universal joint.
2.
Install the final gear case bolts.
3.
Install the brake rod onto the brake
camshaft lever, and then install the
brake pedal free play adjusting nut
onto the brake rod.
4. Install the brake torque rod bolt
and nut at the brake shoe plate.
5.
Install the panel.
6.
Lower the rear wheel so that it is
on the ground.
7.
Tighten the axle nut, the final gear
case bolts and the brake torque
rod nuts to the specified torques.
8. Adjust the brake pedal free play.
(See page 6-23.)
WARNING
EWA10660
After adjusting the brake pedal free
play, check the operation of the
brake light.
1. Bolt
2.
Final gear case
1.
Middle gear universal joint
2.
Drive shaft
Tightening torques:
Axle nut:
92 Nm (9.2 m·kgf, 67 ft·lbf)
Final gear case bolt:
74 Nm (7.4 m·kgf, 54 ft·lbf)
Brake torque rod nut:
20 Nm (2.0 m·kgf, 14 ft·lbf)