2007 Yamaha Motorsports Apex Mountain Owners Manual - Page 79

2007 Yamaha Motorsports Apex Mountain Manual

Get 2007 Yamaha Motorsports Apex Mountain PDF manuals and user guides View all 2007 Yamaha Motorsports Apex Mountain manuals

Page 79 highlights

E_8fp.book Page 24 Tuesday, March 28, 2006 4:35 PM ESU05100 Adjusting the front shock absorber air pressure For RX10RTR/RX10MS This snowmobile is equipped with FOX shock absorbers as standard equipment. The air pressure of the shock absorbers can be adjusted using the special pump 1 included with your snowmobile. NOTE: @ The following procedure applies to both shock absorbers. @ 1. Place the snowmobile on a level surface and apply the parking brake. 2. Lift the front of the snowmobile onto a suitable stand to raise the skis off the ground. WARNING @ Support the snowmobile securely on a suitable stand before adjusting the shock absorbers. @ CAUTION: @ Make sure that there is no load on the shock absorbers and that they are fully extended before making any air pressure adjustments. @ 3. Remove the air valve cap 2 from the shock absorber. 4. Install the hose connector 3 of the special pump onto the air valve of the shock absorber and tighten it approximately six turns until the pressure registers on the pump gauge. CAUTION: @ Do not overtighten the connector onto the air valve as this will damage the connector seal. @ NOTE: @ If the shock absorber has no air pressure, the gauge reading will be zero. @ 8-24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
8-24
ESU05100
Adjusting the front shock absorber air pressure
For RX10RTR/RX10MS
This snowmobile is equipped with FOX shock absorbers
as standard equipment.
The air pressure of the shock absorbers can be adjusted
using the special pump
1
included with your snowmo-
bile.
NOTE:
@
The following procedure applies to both shock absorb-
ers.
@
1. Place the snowmobile on a level surface and apply
the parking brake.
2. Lift the front of the snowmobile onto a suitable stand
to raise the skis off the ground.
WARNING
@
Support the snowmobile securely on a suitable
stand before adjusting the shock absorbers.
@
CAUTION
:
@
Make sure that there is no load on the shock absorb-
ers and that they are fully extended before making
any air pressure adjustments.
@
3. Remove the air valve cap
2
from the shock absorber.
4. Install the hose connector
3
of the special pump
onto the air valve of the shock absorber and tighten it
approximately six turns until the pressure registers on
the pump gauge.
CAUTION
:
@
Do not overtighten the connector onto the air valve
as this will damage the connector seal.
@
NOTE:
@
If the shock absorber has no air pressure, the gauge
reading will be zero.
@
E_8fp.book
Page 24
Tuesday, March 28, 2006
4:35 PM