2006 Yamaha Motorsports RS Vector Owners Manual - Page 71

2006 Yamaha Motorsports RS Vector Manual

Get 2006 Yamaha Motorsports RS Vector PDF manuals and user guides View all 2006 Yamaha Motorsports RS Vector manuals

Page 71 highlights

ESU02921 Adjusting the control rods The weight transfer can be adjusted at the control rods. The following procedure applies to both control rods. 1. Loosen the locknut 2 while holding the control rod adjusting nut 1. 2. To increase weight transfer, turn the adjusting nut in direction a. To decrease weight transfer, turn the adjusting nut in direction b. 3. Tighten the locknut. Locknut tightening torque: 25 Nm (2.5 m·kgf, 18 ft·lb) CAUTION: @ G G When using the two 22-mm wrenches included in the tool kit, make sure that they are situated at a right angle to the control rod as shown, and that they are tightly fitted to the locknut and the control rod adjusting nut. The adjusting nut of the left and right control rods must be set to the same position. Uneven settings can cause poor handling and loss of stability. @ WARNING @ Never adjust the control rods beyond the maximum range indicated on the rods with red paint 3. @ c Adjustable range d Standard position 8-23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
8-23
ESU02921
Adjusting the control rods
The weight transfer can be adjusted at the control rods.
The following procedure applies to both control rods.
1. Loosen the locknut
2
while holding the control rod
adjusting nut
1
.
2. To increase weight transfer, turn the adjusting nut in
direction
a
. To decrease weight transfer, turn the
adjusting nut in direction
b
.
3. Tighten the locknut.
CAUTION
:
@
●
When using the two 22-mm wrenches included in the
tool kit, make sure that they are situated at a right
angle to the control rod as shown, and that they are
tightly fitted to the locknut and the control rod adjust-
ing nut.
●
The adjusting nut of the left and right control rods
must be set to the same position. Uneven settings
can cause poor handling and loss of stability.
@
WARNING
@
Never adjust the control rods beyond the maximum
range indicated on the rods with red paint
3
.
@
c
Adjustable range
d
Standard position
Locknut tightening torque:
25 Nm (2.5 m·kgf, 18 ft·lb)