2006 Yamaha Motorsports Majesty Owners Manual - Page 57

2006 Yamaha Motorsports Majesty Manual

Get 2006 Yamaha Motorsports Majesty PDF manuals and user guides View all 2006 Yamaha Motorsports Majesty manuals

Page 57 highlights

PERIODIC MAINTENANCE AND MINOR REPAIR 1 2 3 4 Tightening torque: Oil filter element cover bolt: 10 Nm (1.0 m·kgf, 7.2 ft·lbf) Recommended engine oil: See page 8-1. Oil quantity: Without oil filter element replacement: 1.50 L (1.59 US qt) (1.32 Imp.qt) With oil filter element replacement: 1.70 L (1.80 US qt) (1.50 Imp.qt) ECA11670 NOTE: Make sure that the O-rings are properly seated. 8. Install the washer and the engine oil drain bolt, and then tighten the drain bolt to the specified torque. Tightening torque: Engine oil drain bolt: 20 Nm (2.0 m·kgf, 14.5 ft·lbf) ECA12910 2 3 4 5 6 7 8 9 1. Oil filter element cover 2. O-ring 3. Compression spring 4. Oil filter element CAUTION: When removing the oil filter element cover, the compression spring will fall out. Take care not to lose the compression spring. 7. Install the compression spring and oil filter element cover by installing the bolts, then tightening them to the specified torque. NOTE: Make sure that the washer is properly seated. 9. Add the specified amount of the recommended engine oil, and then install and tighten the oil filler cap. CAUTION: G Do not use oils with a diesel specification of "CD" or oils of a higher quality than specified. In addition, do not use oils labeled "ENERGY CONSERVING II" or higher. G Be sure no foreign material enters the crankcase. 10. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and check for the cause. 11. Reset the oil change indicator according to the following procedure. To reset the oil change indicator 1. Turn the key to "ON". 6-16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
PERIODIC MAINTENANCE AND MINOR REPAIR
6-16
2
3
4
5
6
7
8
9
CAUTION:
ECA12910
When removing the oil filter element
cover, the compression spring will
fall out. Take care not to lose the
compression spring.
7. Install the compression spring and
oil filter element cover by installing
the bolts, then tightening them to
the specified torque.
NOTE:
Make sure that the O-rings are properly
seated.
8. Install the washer and the engine
oil drain bolt, and then tighten the
drain bolt to the specified torque.
NOTE:
Make sure that the washer is properly
seated.
9. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler cap.
CAUTION:
ECA11670
●
Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
●
Be sure no foreign material en-
ters the crankcase.
10. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
11. Reset the oil change indicator ac-
cording to the following procedure.
To reset the oil change indicator
1. Turn the key to “ON”.
1. Oil filter element cover
2. O-ring
3. Compression spring
4. Oil filter element
1
2
3
4
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Tightening torque:
Engine oil drain bolt:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter element replace-
ment:
1.50 L (1.59 US qt) (1.32 Imp.qt)
With oil filter element replacement:
1.70 L (1.80 US qt) (1.50 Imp.qt)