2006 Yamaha Motorsports Apex RTX Owners Manual - Page 71

2006 Yamaha Motorsports Apex RTX Manual

Get 2006 Yamaha Motorsports Apex RTX PDF manuals and user guides View all 2006 Yamaha Motorsports Apex RTX manuals

Page 71 highlights

7. If the position is incorrect, adjust the V-belt position by removing or adding a spacer 4 on each adjusting bolt 5. CD-06E V-belt position More than 1.5 mm (0.06 in) above the edge From 1.5 mm (0.06 in) above the edge to 0.5 mm (0.02 in) below the edge More than 0.5 mm (0.02 in) below the edge Adjustment Remove spacer Not necessary (It is correct.) Add spacer 8. Tighten the adjusting bolts. Adjusting bolt tightening torque: 10 Nm (1.0 m·kgf, 7.2 ft·lb) 9. Install the V-belt over the primary sheave assembly. 10. Rotate the secondary sliding sheave clockwise 6 and push 7 it so that it separates from the secondary fixed sheave. 11. Install the V-belt 8 between the secondary sliding and fixed sheaves. 12. Install the drive guard. 13. Install the left side cover and the shroud. WARNING @ Never run the engine with the V-belt or drive guard removed. @ 8-18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
8-18
7. If the position is incorrect, adjust the V-belt position
by removing or adding a spacer
4
on each adjusting
bolt
5
.
CD-06E
8. Tighten the adjusting bolts.
9. Install the V-belt over the primary sheave assembly.
10. Rotate the secondary sliding sheave clockwise
6
and push
7
it so that it separates from the secondary
fixed sheave.
11. Install the V-belt
8
between the secondary sliding
and fixed sheaves.
12. Install the drive guard.
13. Install the left side cover and the shroud.
WARNING
@
Never run the engine with the V-belt or drive guard
removed.
@
V-belt position
Adjustment
More than 1.5 mm (0.06 in)
above the edge
Remove spacer
From 1.5 mm (0.06 in)
above the edge to 0.5 mm
(0.02 in) below the edge
Not necessary
(It is correct.)
More than 0.5 mm (0.02 in)
below the edge
Add spacer
Adjusting bolt tightening torque:
10 Nm (1.0 m·kgf, 7.2 ft·lb)