2005 Yamaha Motorsports VMAX Owners Manual - Page 56

2005 Yamaha Motorsports VMAX Manual

Get 2005 Yamaha Motorsports VMAX PDF manuals and user guides View all 2005 Yamaha Motorsports VMAX manuals

Page 56 highlights

PERIODIC MAINTENANCE AND MINOR REPAIR 1. Radiator cap 1. Water pump drain bolt 1. Rubber coolant drain plug 5. Turn the coolant drain cock, making sure to align the "ON" with the position indicator. 6 7. Remove the cylinder drain plug covers on the outside of the cylinder blocks by removing the screws. 9. After the coolant is completely drained, thoroughly flush the cooling system with clean tap water. 10. Install the water pump drain bolt, and then tighten it to the specified torque. NOTE: Check the washer for damage and replace it if necessary. Tightening torque: Water pump drain bolt: 43 Nm (4.3 m·kgf, 31 ft·lbf) 1. Coolant drain cock 2. Position indicator 1. Screw 6. Remove the water pump drain bolt to drain the water pump housing. 8. Remove the rubber coolant drain plugs to drain the coolant from the engine. 6-16 11. Install the rubber coolant drain plugs, and then install the cylinder drain plug covers.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
PERIODIC MAINTENANCE AND MINOR REPAIR
6-16
6
5.
Turn the coolant drain cock, mak-
ing sure to align the “ON” with the
position indicator.
6.
Remove the water pump drain bolt
to drain the water pump housing.
7. Remove the cylinder drain plug
covers on the outside of the cylin-
der
blocks
by
removing
the
screws.
8. Remove the rubber coolant drain
plugs to drain the coolant from the
engine.
9. After the coolant is completely
drained, thoroughly flush the cool-
ing system with clean tap water.
10. Install the water pump drain bolt,
and then tighten it to the specified
torque.
NOTE:
Check the washer for damage and re-
place it if necessary.
11. Install the rubber coolant drain
plugs, and then install the cylinder
drain plug covers.
1.
Radiator cap
1.
Coolant drain cock
2.
Position indicator
1.
Water pump drain bolt
1. Screw
1.
Rubber coolant drain plug
Tightening torque:
Water pump drain bolt:
43 Nm (4.3 m·kgf, 31 ft·lbf)