2004 Yamaha Motorsports Vino 125 Owners Manual - Page 59

2004 Yamaha Motorsports Vino 125 Manual

Get 2004 Yamaha Motorsports Vino 125 PDF manuals and user guides View all 2004 Yamaha Motorsports Vino 125 manuals

Page 59 highlights

PERIODIC MAINTENANCE AND MINOR REPAIR To change the engine oil and clean the oil strainer 1 4 3 2 1 1 2 1 ZAUM00** ZAUM00** 1 3 1. 2. 3. 4. Drain bolt B O-ring Spring Strainer ZAUM00** 1. Drain bolt A ECA10410 4 5 6 7 8 9 1. Oil filler cap cC When removing the engine oil drain bolt, the O-ring, spring, and oil strainer will fall out. Take care not to lose these parts. 5. Clean the oil strainer with solvent, and then check it for damage and replace it if necessary. 1. Start the engine, warm it up for several minutes, and then turn it off. 2. Place an oil pan under the engine to collect the used oil. 3. Remove panel A. (See page 6-6.) 4. Remove the engine oil filler cap and drain bolts to drain the oil from the crankcase. 6.Check the O-ring for damage and replace it if necessary. 7. Install the oil strainer, spring, O-ring and engine oil drain bolts, and then tighten the drain bolts to the specified torque. Tightening torque: Engine oil drain bolt A: 23 Nm (2.3m • kgf, 16.6ft • lbf) Engine oil drain bolt B: 32 Nm (3.2m • kgf, 23.1ft • lbf) 6-25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
6-25
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
To change the engine oil and clean
the oil strainer
1
ZAUM00**
1.
Oil filler cap
1.
Start the engine, warm it up for sev-
eral minutes, and then turn it off.
2.
Place an oil pan under the engine
to collect the used oil.
3.
Remove panel A. (See page 6-6.)
4.
Remove the engine oil filler cap and
drain bolts to drain the oil from the
crankcase.
4
3
2
1
1
ZAUM00**
1.
Drain bolt B
2. O-ring
3. Spring
4. Strainer
6.Check the O-ring for damage and re-
place it if necessary.
7.
Install the oil strainer, spring, O-ring
and engine oil drain bolts, and then
tighten the drain bolts to the speci-
fied torque.
Tightening torque:
Engine oil drain bolt A:
23 Nm (2.3m • kgf, 16.6ft • lbf)
Engine oil drain bolt B:
32 Nm (3.2m • kgf, 23.1ft • lbf)
1
ZAUM00**
1.
Drain bolt A
ECA10410
c
C
When removing the engine oil drain
bolt, the O-ring, spring, and oil
strainer will fall out. Take care not to
lose these parts.
5.
Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.