2002 Yamaha Motorsports SXViper Owners Manual - Page 50

2002 Yamaha Motorsports SXViper Manual

Get 2002 Yamaha Motorsports SXViper PDF manuals and user guides View all 2002 Yamaha Motorsports SXViper manuals

Page 50 highlights

ESU00251 Maximizing drive track life Recommendations Track tension During initial break-in, the new drive track will tend to stretch quickly as the track settles. Be sure to correct the track tension and alignment frequently. (See pages 8-24-8-26 for adjustment procedures.) A loose track can slip (ratchet), derail or catch on suspension parts causing severe damage. Do not overtighten the drive track, otherwise it may increase the friction between the track and the slide runners, resulting in the rapid wear of both components. Also, this may put an excessive load on the suspension components, resulting in component failure. Marginal snow The drive track and the slide runners are lubricated and cooled by snow and water. To prevent the drive track and slide runners from overheating, avoid sustained highspeed usage in areas such as icy trails, frozen lakes and rivers that have minimal snow coverage. An overheated track will be weakened internally, which may cause failure or damage. Off-trail riding Avoid off-trail riding until there is sufficient snow coverage. It generally takes several feet of snow to provide a good overall base to properly cover debris, such as rocks, logs, etc. If snow coverage is not sufficient, stay on trails to avoid impact damage to the drive track. Studded track In general, track life will be shortened when studs are installed. Drilling stud holes into the drive track will cut the internal fibers, which weakens the track. Avoid spinning the drive track. Studs may catch on an object and pull out of the track, leaving tears and damage around the already weakened area. To minimize possible damage, consult your stud manufacturer for installation and stud pattern recommendations. Yamaha does not recommend track studding. 7-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
7-10
ESU00251
Maximizing drive track life
Recommendations
Track tension
During initial break-in, the new drive track will tend to
stretch quickly as the track settles. Be sure to correct the
track tension and alignment frequently. (See pages
8-24–8-26 for adjustment procedures.) A loose track can
slip (ratchet), derail or catch on suspension parts caus-
ing severe damage. Do not overtighten the drive track,
otherwise it may increase the friction between the track
and the slide runners, resulting in the rapid wear of both
components. Also, this may put an excessive load on the
suspension components, resulting in component failure.
Marginal snow
The drive track and the slide runners are lubricated and
cooled by snow and water. To prevent the drive track and
slide runners from overheating, avoid sustained high-
speed usage in areas such as icy trails, frozen lakes and
rivers that have minimal snow coverage. An overheated
track will be weakened internally, which may cause fail-
ure or damage.
Off-trail riding
Avoid off-trail riding until there is sufficient snow cover-
age. It generally takes several feet of snow to provide a
good overall base to properly cover debris, such as
rocks, logs, etc. If snow coverage is not sufficient, stay on
trails to avoid impact damage to the drive track.
Studded track
In general, track life will be shortened when studs are
installed. Drilling stud holes into the drive track will cut
the internal fibers, which weakens the track. Avoid spin-
ning the drive track. Studs may catch on an object and
pull out of the track, leaving tears and damage around
the already weakened area. To minimize possible dam-
age, consult your stud manufacturer for installation and
stud pattern recommendations.
Yamaha does not recommend track studding.