2009 Polaris 550 IQ Shift Owners Manual - Page 35

2009 Polaris 550 IQ Shift Manual

Get 2009 Polaris 550 IQ Shift PDF manuals and user guides View all 2009 Polaris 550 IQ Shift manuals

Page 35 highlights

THE PERFECT FIT Rear Suspension Adjustments Initial Spring Preload Setting (Sag Method) To set up the rear suspension torsion spring preload, measure the distance between the ground and rear bumper. This is measurement X. Take the first measurement with no rider and with the rear suspension at full extension. NOTE: The rear bumper may need to be lifted upward slightly to fully extend the rear suspension. X Next, have the rider drop down hard on the seat and bounce up and down several times, collapsing the rear suspension. With the rider seated, measure the distance between the ground and the rear bumper at the exact location used for measurement X. This is measurement Y. Y To determine sag, commonly referred to as ride-in, subtract measurement Y from X (sag=X-Y). If the measured sag is incorrect, adjust the FRA position and/or rear torsion spring preload. Suspension Recommended Sag IQ (121) 4-5 inches (10-13 cm) Adjustment Torsion Spring Preload See Page 33 NOTE: This is only an initial setup, and final spring preload may vary based on rider preference and riding conditions. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
32
THE PERFECT FIT
Rear Suspension Adjustments
Initial Spring Preload Setting (Sag Method)
To set up the rear suspension torsion
spring preload, measure the distance
between the ground and rear
bumper.
This is measurement X.
Take the first measurement with no
rider and with the rear suspension at
full extension.
NOTE:
The rear bumper may need to
be lifted upward slightly to fully
extend the rear suspension.
Next, have the rider drop down hard
on the seat and bounce up and down
several times, collapsing the rear
suspension. With the rider seated,
measure the distance between the
ground and the rear bumper at the
exact location used for measurement
X. This is measurement Y.
To determine sag, commonly
referred to as ride-in, subtract measurement Y from X (sag=X-Y).
If the
measured sag is incorrect, adjust the FRA position and/or rear torsion
spring preload.
NOTE:
This is only an initial setup, and final spring preload may vary based on
rider preference and riding conditions.
Suspension
Recommended Sag
Adjustment
See
Page
IQ (121)
4-5 inches (10-13 cm)
Torsion Spring
Preload
33
X
Y