2008 Polaris 700 RMK Owners Manual - Page 92

2008 Polaris 700 RMK Manual

Get 2008 Polaris 700 RMK PDF manuals and user guides View all 2008 Polaris 700 RMK manuals

Page 92 highlights

Cooling System MAINTENANCE Bleeding the Cooling System Bleed the cooling system at the intervals outlined in the Periodic Maintenance Table beginning on page 72. Perform the bleeding procedure when the engine is cold. 1. Remove the pressure cap and fill the coolant bottle with properly mixed coolant to the maximum mark. 2. Elevate the front end of the machine slightly to aid in bleeding of the heat exchangers. 3. Remove the bleed screw from the water outlet manifold and/or the thermostat housing. Allow the coolant to bleed through the system until it runs out the bleed holes. Reinstall the bleed screw into the manifold. 4. Add coolant to the coolant bottle to the maximum mark. 5. Start the engine and run at a fast idle for two to three minutes. Loosen the bleed screw occasionally to purge any trapped air. 6. Stop the engine and check the coolant bottle level. Fill as required. 7. Feel the heat exchangers under the running boards. If the system is bled properly, they'll be warm to the touch. If they're not, repeat step 5. Lift the front of the machine slightly to assist in the bleeding. 8. Replace the pressure cap and carefully lower the front end of the machine. 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
89
MAINTENANCE
Cooling System
Bleeding the Cooling System
Bleed the cooling system at the intervals outlined in the Periodic Main-
tenance Table beginning on page 72. Perform the bleeding procedure
when the engine is cold.
1.
Remove the pressure cap and fill the coolant bottle with properly
mixed coolant to the maximum mark.
2.
Elevate the front end of the machine slightly to aid in bleeding of
the heat exchangers.
3.
Remove the bleed screw from the water outlet manifold and/or the
thermostat housing. Allow the coolant to bleed through the system
until it runs out the bleed holes. Reinstall the bleed screw into the
manifold.
4.
Add coolant to the coolant bottle to the maximum mark.
5.
Start the engine and run at a fast idle for two to three minutes.
Loosen the bleed screw occasionally to purge any trapped air.
6.
Stop the engine and check the coolant bottle level. Fill as required.
7.
Feel the heat exchangers under the running boards. If the system is
bled properly, they'll be warm to the touch. If they're not, repeat step
5. Lift the front of the machine slightly to assist in the bleeding.
8.
Replace the pressure cap and carefully lower the front end of the
machine.