2009 BMW M5 Owner's Manual - Page 229

2009 BMW M5 Manual

Page 229 highlights

4. Screw dust cap off valve of defective wheel and screw filling hose 2 of sealant bottle onto valve. 5. Insert sealant bottle on compressor housing so that it is positioned upright. 4. Correct tire inflation pressure to 29 psi/ 200 kPa. With the ignition switched on: > Increase inflation pressure: switch on compressor, position I. To check currently set inflation pressure, briefly switch off device. Do not allow compressor to run longer than 10 minutes, otherwise the device will overheat and may be damaged.< > Reduce inflation pressure: press button 8 or turn screw 8 on pressure gauge. 6. Make sure that the device is switched off, position 0. 7. Insert connector 3 into lighter socket in vehicle interior, refer to page 109. 8. With the ignition switched on: Switch on the device and allow to run for approx. 3 minutes to fill wheel with sealant. It is not important what inflation pressure the tire has after filling. 9. Switch off device. 10. Remove connecting hose from connection of sealant bottle and tire valve. Stow the M Mobility System in the vehicle again. If the inflation pressure is not held, drive the vehicle again, refer to Distributing sealant. Then repeat steps 1 to 4 once. Using the M Mobility System can be ineffective in the event of tire damage greater than approx. 0.16 in/4 mm in size. Please contact the nearest BMW center, refer to page 232, or a workshop that works according to BMW repair procedures with correspondingly trained personnel if the tire cannot be made ready for driving with the M Mobility System.< The tire inflation pressure must be at least 29 psi/200 kPa. Otherwise do not continue driving.< Continue driving Do not exceed the permissible maximum speed of 50 mph/80 km/h, otherwise accidents can occur.< Reinitialize the Flat Tire Monitor. For details, refer to page 84. Have the defective tire and the sealant bottle of the M Mobility System replaced as soon as possible.< Distributing sealant Immediately drive approx. 2 miles/3 km so that sealant is evenly distributed in tire. Do not exceed a maximum speed of 35 mph/60 km/h. Do not drop below 12 mph/20 km/h if possible.< Producing tire inflation pressure Mobility Reference 1. After approx. 2 miles/3 km, stop at suitable location. 2. Screw compressor hose 9 directly onto tire valve. 3. Insert connector 3 in lighter socket in vehicle interior. Changing wheels* Safety precautions in the event of a flat tire or wheel change: Park the vehicle as far as possible from passing traffic and on solid ground. Switch on the hazard warning flashers. Apply the handbrake and shift into first gear or reverse with the manual transmission, or move 227 Online Edition for Part no. 01 41 2 600 738 - © 08/08 BMW AG Communications Entertainment Navigation Driving tips Controls At a glance

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266

Mobility
227
Reference
At a glance
Controls
Driving tips
Communications
Navigation
Entertainment
4.
Screw dust cap off valve of defective wheel
and screw filling hose
2
of sealant bottle
onto valve.
5.
Insert sealant bottle on compressor hous-
ing so that it is positioned upright.
6.
Make sure that the device is switched off,
position 0.
7.
Insert connector
3
into lighter socket in
vehicle interior, refer to page
109
.
8.
With the ignition switched on:
Switch on the device and allow to run for
approx. 3 minutes to fill wheel with sealant.
It is not important what inflation pressure
the tire has after filling.
9.
Switch off device.
10.
Remove connecting hose from connection
of sealant bottle and tire valve.
Stow the M Mobility System in the vehicle
again.
Distributing sealant
Immediately drive approx. 2 miles/3 km so that
sealant is evenly distributed in tire.
Do not exceed a maximum speed of
35 mph/60 km/h. Do not drop below
12 mph/20 km/h if possible.
<
Producing tire inflation pressure
1.
After approx. 2 miles/3 km, stop at suitable
location.
2.
Screw compressor hose
9
directly onto tire
valve.
3.
Insert connector
3
in lighter socket in vehi-
cle interior.
4.
Correct tire inflation pressure to 29 psi/
200 kPa. With the ignition switched on:
>
Increase inflation pressure: switch on
compressor, position I. To check cur-
rently set inflation pressure, briefly
switch off device.
Do not allow compressor to run
longer than 10 minutes, otherwise
the device will overheat and may be dam-
aged.
<
>
Reduce inflation pressure: press
button
8
or turn screw
8
on pressure
gauge.
If the inflation pressure is not held, drive
the vehicle again, refer to Distributing
sealant. Then repeat steps 1 to 4 once.
Using the M Mobility System can be ineffective
in the event of tire damage greater than
approx.
0.16
in/4
mm in size. Please contact the
nearest BMW center, refer to page
232
, or a
workshop that works according to BMW repair
procedures with correspondingly trained per-
sonnel if the tire cannot be made ready for driv-
ing with the M Mobility System.
<
The tire inflation pressure must be at least
29 psi/200 kPa. Otherwise do not con-
tinue driving.
<
Continue driving
Do not exceed the permissible maximum
speed of 50 mph/80 km/h, otherwise
accidents can occur.
<
Reinitialize the Flat Tire Monitor.
For details, refer to page
84
.
Have the defective tire and the sealant bottle of
the M Mobility System replaced as soon as
possible.
<
Changing wheels*
Safety precautions in the event of a flat
tire or wheel change: Park the vehicle as
far as possible from passing traffic and on solid
ground. Switch on the hazard warning flashers.
Apply the handbrake and shift into first gear or
reverse with the manual transmission, or move
Online Edition for Part no. 01 41 2 600 738 - © 08/08 BMW AG