Yamaha CRW8824S Owners Manual

Yamaha CRW8824S - CRW - CD-RW Drive Manual

Get Yamaha CRW8824S - CRW - CD-RW Drive PDF manuals and user guides View all Yamaha CRW8824S manuals
Add to My Manuals
Save this manual to your list of manuals

Yamaha CRW8824S manual content summary:

  • Yamaha CRW8824S | Owners Manual - Page 1
  • Yamaha CRW8824S | Owners Manual - Page 2
    Yamaha Corporation of America 6600 Orangethorpe Ave. Buena Park, CA 90620 714-522-9011 714-228-3913 CD Recordable/Rewritable Drive CRW8824S CRW8824S-NB instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha to eliminate the problem by using one
  • Yamaha CRW8824S | Owners Manual - Page 3
    CD-REWRITABLE DRIVE MODEL NO. CRW8824E MADE IN MALAYSIA COMPLIES WITH 21 CFR CHAPTER 1, SUBCHAPTER J. YAMAHA CORPORATION 10-1 NAKAZAWA-CHO, appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT LUOKAN 1 LASERLAITE KLASS 1 LASER
  • Yamaha CRW8824S | Owners Manual - Page 4
    English OWNER'S MANUAL i
  • Yamaha CRW8824S | Owners Manual - Page 5
    to the device. Return the device immediately to the store at which it was purchased or alternatively, to the nearest Yamaha Service Center (listed at the back of this manual). Make sure the computer is electrically grounded Otherwise, there is an increased risk of electrical shock. When opening up
  • Yamaha CRW8824S | Owners Manual - Page 6
    . Set the device up according to the instructions in the Owner's Manual. Always remove the disc from the tray servicing charges, contact the store at which the device was purchased or alternatively, the nearest Yamaha Service Center (listed at the back of this manual). The device should be serviced
  • Yamaha CRW8824S | Owners Manual - Page 7
    this manual is subject to change without prior notice. 2. All trademarks contained in this manual belong to their respective owners. 3. Yamaha does copyrights for that product. WARRANTY YAMAHA AND SUPPLIERS ACCEPT NO LIABILITY FOR THE LOSS OF ANY DATA OR ANY PROBLEMS CAUSED AS A RESULT. AS
  • Yamaha CRW8824S | Owners Manual - Page 8
    a Disc 24 Ejecting the Disc 24 Ejecting a Disc in an Emergency 25 Troubleshooting 26 Appendix ...29 Writing Modes 29 About the firmware 31 LED Indicator Messages 32 CRW8824E Specifications 33 Index 35 ©2000 Yamaha Corporation. All Rights Reserved. This document may not, in whole or in part
  • Yamaha CRW8824S | Owners Manual - Page 9
    that the adapter card is recognized correctly by the computer's OS. STEP Install the SCSI adapter card 1-2 Read this manual and insert the SCSI card into the appropriate PCI slot on the computer. STEP Set up the CRW8824S drive 3 1. Set the jumper switches (P.10) 2. Fit the drive into the computer
  • Yamaha CRW8824S | Owners Manual - Page 10
    CRW8824S Drive High speed CD-R/RW discs can be written/rewritten at up to 8X speed. For example, an audio CD (74 minutes/650 MB) can be created in approximately 10 minutes. Data reading at up to 24X speed is supported. CD TEXT support . Reliable writing Yamaha's proprietary Pure- this problem by automatically adjusting
  • Yamaha CRW8824S | Owners Manual - Page 11
    SCSI devices (including the CRW8824S) to your computer. Make sure it has an internal bus connector. Yamaha recommends any of Adaptec's AHA-2940-series cards (PCI slot). Software The software requirements for using the CRW8824S drive are as follows: CD writing software. This software must support
  • Yamaha CRW8824S | Owners Manual - Page 12
    of CD-RW discs: those that support write/rewrite speeds of 4X, 2X and 1X, and those that support only 2X. • The CRW8824S can write/rewrite at 4X and 2X to read these discs on a Yamaha CD-R/RW drive not bearing the High Speed CD-RW logo. URL: http://www.yamaha.co.jp/english/product/computer/ The
  • Yamaha CRW8824S | Owners Manual - Page 13
    which the video and audio data has been com- pressed using MPEG-1 technology. Tools You will need the following tools at hand when installing the CRW8824S drive. Phillips Screwdriver You will need to use this when removing the cover of your computer and when mounting the drive. You may also need
  • Yamaha CRW8824S | Owners Manual - Page 14
    Front and Rear of Unit Front Panel The CRW8824S drive's front panel features the following: Manual Eject hole Only use this if no other method is available for unloading a disc. Disc tray The tray is used to hold the disc. It
  • Yamaha CRW8824S | Owners Manual - Page 15
    CRW8824S drive's rear panel features the following: SCSI connector Insert the connector of the SCSI ribbon cable here. Make sure you align the red line of the ribbon cable with pin 1 of the drive's connector, marked "SCSI plastic shunts in order to manually assign a SCSI ID number for the drive.
  • Yamaha CRW8824S | Owners Manual - Page 16
    CRW8824S drive out of its packaging, you should immediately note down the serial number shown on the top of the drive together with a barcode. You may need to refer to this number when requesting User Support services YAMAHA CRW8824S á la norme NMB-003 du Canada. CLASS 1 LASER PRODUCT LASER KLASSE
  • Yamaha CRW8824S | Owners Manual - Page 17
    Installation To set each jumper switch, you have to bridge the two pins in the respective column of the grid with a plastic shunt. Shunts are already attached to the jumper switches in their default configurations. Rear Panel AUDIO OUT R G L 1 24 IPTBDAELORRSEIMCTLKIYNESACITTZOER 1 SICNCOTSNE+
  • Yamaha CRW8824S | Owners Manual - Page 18
    on the chain must be unique. Make sure the CRW8824S drive's SCSI ID number is not the same as that of any other device on the chain. By factory default, the CRW8824S is assigned ID number"3"but this can be changed. If the SCSI card supports SCAM and SCAM is turned "ON," a different ID number
  • Yamaha CRW8824S | Owners Manual - Page 19
    from being reflected off the last device in the chain. The SCSI terminator switch should be set to "ON" if the CRW8824S is the last device on the internal SCSI chain. If the CRW8824S is not the last device on the internal SCSI chain, the shunt on the Terminator jumper switch should be removed
  • Yamaha CRW8824S | Owners Manual - Page 20
    TERMINATOR BLOCK SIZE Installation Termination OFF 1 24 ID SELECT PARITY TERMINATOR BLOCK SIZE Set to "ON" if CRW8824S drive is last device on SCSI chain 4 Block Size The data block size of the CRW8824S can be set to 512 bytes per sector by setting the Block Size jumper switch to "ON." This
  • Yamaha CRW8824S | Owners Manual - Page 21
    a spare 5.25-inch drive bay available, such as with many desktop-type designs, you can replace the computer's existing CD-ROM drive with the CRW8824S drive. CD-ROM drive CRW8824S When replacing an IDE-type CD-ROM drive with the CRW8824S drive, you will also need a SCSI adapter card and an internal
  • Yamaha CRW8824S | Owners Manual - Page 22
    Installation If you proceed without doing this, you run the risk of receiving an electric shock and/or short-circuiting and damaging components including the CRW8824S drive. 2 Remove the outer casing of the computer. If you need to remove screws in the process, make sure you don't lose them. The
  • Yamaha CRW8824S | Owners Manual - Page 23
    Installation 3 Touch a metal part of the computer's chassis or power supply unit to drain any static charge that may have built up inside your body. Drain any static charge You can permanently damage equipment if you touch it while there is any static charge in your body. 4 Remove the front cover of
  • Yamaha CRW8824S | Owners Manual - Page 24
    card termination To connect internally-mounted SCSI devices, the SCSI adapter card's on-board internal SCSI termination must be switched ON. With most cards, this is done automatically. If your SCSI adapter card requires that you manually disable internal termination, refer to the documentation
  • Yamaha CRW8824S | Owners Manual - Page 25
    cable with Pin 1 of the card's SCSI connector. Next, connect a free 50-pin connector on the SCSI flat cable to the back of the CRW8824S drive such that the red line on the cable is aligned with pin 1, marked "SCSI INTERFACE CONNECTOR 1." SCSI adapter card 50-pin SCSI flat cable Align red line with
  • Yamaha CRW8824S | Owners Manual - Page 26
    other end of the cable is connected to "AUDIO OUT" of the CRW8824S drive. Make sure connector's lug is at the top. Audio cable write audio CDs since the audio is passed over the SCSI bus. It is required for playing back audio CDs on the CRW8824S drive via the computer's sound card. However, if a
  • Yamaha CRW8824S | Owners Manual - Page 27
    Installation 8 Connect a 4-pin power cable to the power supply connector of the CRW8824S marked "DC INPUT." AUDIO OUT R G L 1 24 IPTBDAELORRSEIMCTLKIYNESACITTZOER 1 SICNCOTSNE+INR5EVFDACCCTOEGINRPU+1T2V Top 4-pin power cable Bottom There may be more than one 4-pin power cable available.
  • Yamaha CRW8824S | Owners Manual - Page 28
    Installation ) Attach the outer casing of the computer and any screws that were removed. ! Reconnect the computer to the AC outlet and power it up. When you power up the computer, make sure both LEDs on the panel of the CRW8824S light up together for brief moment. 20
  • Yamaha CRW8824S | Owners Manual - Page 29
    -clicking on SCSI Adapter and clicking the Devices tab. For Windows 2000, double-click System in the Control Panel, select the Hardware tab, and click the Device Manager button in System Properties. * This is a screen shown in the Windows 98 environment. # Double-click "YAMAHA CRW8824S" listed
  • Yamaha CRW8824S | Owners Manual - Page 30
    outlet. If you proceed without doing this, you run the risk of receiving an electric shock and/or short-circuiting and damaging components including the CRW8824S drive. 2 Remove the outer casing of the computer. If you need to remove screws in the process, make sure you don't lose them. The method
  • Yamaha CRW8824S | Owners Manual - Page 31
    Installation 3 Touch a metal part of the computer's chassis or power supply unit to drain any static charge that may have built up inside your body. Drain any static charge You can permanently damage equipment if you touch it while there is any static charge in your body. 4 Disconnect all the
  • Yamaha CRW8824S | Owners Manual - Page 32
    slide the drive forward and out from the drive bay. Slide the CRW8824S drive backwards into the now-vacant bay without applying excessive force. CD-ROM drive CRW8824S 6 Leave enough room behind the drive for connecting the power, SCSI and audio cables. Then tighten the four fastening screws on the
  • Yamaha CRW8824S | Owners Manual - Page 33
    . 7 Connect one end of the 50-pin SCSI flat cable to the computer's SCSI adapter card. Align the red line of the cable with Pin 1 of the card's SCSI connector. Next, connect a free 50-pin connector on the SCSI flat cable to the back of the CRW8824S drive such that the red line on the
  • Yamaha CRW8824S | Owners Manual - Page 34
    at other end of the cable is connected to "AUDIO OUT" of the CRW8824S drive. Make sure connector's lug is at the top. Vertically-mounted type ( CDs since the audio is passed over the SCSI bus. It is required for playing back audio CDs on the CRW8824S drive via the computer's sound card. However
  • Yamaha CRW8824S | Owners Manual - Page 35
    Installation 9 Connect the 4-pin power cable to the power supply connector of the CRW8824S marked "DC Input." AUDIO OUT R G L 1 24 IPTBDAELORRSEIMCTLKIYNESACITTZOER 1 SICNCOTSNE+INR5EVFDACCCTOEGINRPU+1T2V Top 4-pin power cable Bottom There may be more than one 4-pin power cable available.
  • Yamaha CRW8824S | Owners Manual - Page 36
    Installation ! Attach the outer casing of the computer and any screws that were removed. @ Reconnect the computer to the AC outlet and power it up. When you power up the computer, make sure both LEDs on the panel of the CRW8824S light up together for brief moment. 28
  • Yamaha CRW8824S | Owners Manual - Page 37
    SCSI Adapter and clicking the Devices tab. For Windows 2000, double-click System in the Control Panel, select the Hardware tab, and click the Device Manager button in System Properties. $ Double-click "YAMAHA CRW8824S automatically be selected if the SCSI adapter card supports this feature. You will
  • Yamaha CRW8824S | Owners Manual - Page 38
    drive after you have installed it. Make sure the computer is powered up. Loading a Disc 1 2 1 Press the Eject button on the CRW8824S drive's front panel. 2 Place the disc onto the tray with its label or printing facing upward. 3 Press the Eject button to close the tray. When a
  • Yamaha CRW8824S | Owners Manual - Page 39
    disc tray while a disc is being read or in other situations, depending on the SCSI command. Only remove the disc after the disc tray has opened fully. Otherwise, you risk damaging the drive or the disc. Manually Ejecting a Disc in an Emergency If the disc tray fails to open for some reason
  • Yamaha CRW8824S | Owners Manual - Page 40
    ://www.yamaha-yste.com/ (Europe) The drive does not power up. Is the 4-pin power cable from the computer's power supply attached correctly? The computer does not start up. Is the SCSI card installed correctly? Please read the instructions that came with your SCSI card for details. The CRW8824S drive
  • Yamaha CRW8824S | Owners Manual - Page 41
    to OFF. (¡P. 11) Is the termination on the SCSI card set such that internal SCSI devices can be connected? Please read the instructions that came with your SCSI card for details. To write to CD-R/RW discs, your CD writing software must support the CRW8824S drive. To find out if it does, contact the
  • Yamaha CRW8824S | Owners Manual - Page 42
    (¡P. 38) Disconnect the SCSI cable from the drive but leave the power cable connected, then load a disc. There may be problems with the disc itself. should contact your nearest Yamaha dealer. Errors occur when backing up at 6X or 8X speed from a separate CD-ROM drive to the CRW8824S drive. A possible
  • Yamaha CRW8824S | Owners Manual - Page 43
    Appendix Writing Modes Disc-at-Once (DAO) This mode is used when writing a complete disc in a single pass without pausing. Data cannot be added later, even if the full capacity of the blank disc has not been used. Example: General CD-ROM 0 650MB Data Lead-in Example: Audio CD 0 Track 1
  • Yamaha CRW8824S | Owners Manual - Page 44
    similar to a floppy disk. This mode is useful when making small incremental backups of data. You will need to use software which specifically supports packet writing, such as Adaptec's DirectCD. 12345678 Packet Same as writing to floppy or hard disk Discs must be formatted before they can be
  • Yamaha CRW8824S | Owners Manual - Page 45
    Manager tab, double-click on CDROM, then double-click on YAMAHA CRW8824S. SCSI ID number When updating the CRW8824S drive's firmware, you will need to enter its SCSI ID number. You can check the number here. The firmware version number will increase as more improvements are incorporated. * This
  • Yamaha CRW8824S | Owners Manual - Page 46
    LED Indicator Messages Appendix Status Power on (reset) Ready (no disc) Loading disc Ejecting disc Ready (disc loaded) Seeking Preparing to write Writing Writing (test mode) Reading q Lit: Orange Lit: Green ON/DISC LED Blinking: Orange Blinking: Green -: Off READ/WRITE LED 38
  • Yamaha CRW8824S | Owners Manual - Page 47
    Appendix CRW8824S Specifications Supported Formats CD-DA CD-G Write q q CD TEXT q CD-ROM (*1) q Mixed Mode CD-ROM (CD-ROM+CD-DA) CD-ROM XA (*1) Photo CD (*1) Video CD CD-i q q q (*2) q q
  • Yamaha CRW8824S | Owners Manual - Page 48
    msec (reading) 2,048 ~ 2,352 B 512 B (read only) SCSI-3 (Ultra SCSI) Horizontal Tray loading Line Out Frequency Range: 20 ~ 20,000Hz Output : 198.1 mm 0.95 kg The CRW8824S series complies with the following specifications Country / Region USA Canada EU Australia New Zealand Japan Category Safety
  • Yamaha CRW8824S | Owners Manual - Page 49
    disc 30 Long-Nosed Pliers 5 lug 18, 26 M manual eject hole 6, 31 Multisession 35 B BIOS 32 block 35 E Eject button 6 Ejecting the Disc 30 F firmware 37 front panel 6 H headphone jack 6 headphone volume SCSI adapter card 17, 25 SCSI connector 7 SCSI driver 32 SCSI flat cable 17, 25 SCSI
  • Yamaha CRW8824S | Owners Manual - Page 50
    : +1 714 522 9011 FAX: +1 714 228 3913 URL: http://www.yamaha.com/ CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario M1S 3R1, CANADA TEL: +1 416 298 1331 FAX: +1 416 292 0732 AUSTRALIA Yamaha Music Australia Pty., Ltd. Level 1, 99 Queensbridge Street Southbank, Victoria 3006
  • Yamaha CRW8824S | Owners Manual - Page 51
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51