Weider Pro 3750 User Manual
Weider Pro 3750 Manual
 |
View all Weider Pro 3750 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider Pro 3750 manual content summary:
- Weider Pro 3750 | User Manual - Page 1
you have questions, or if there are missing or damaged parts, we will guarantee complete satisfaction through direct assistance from our Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL Visit our website at - Weider Pro 3750 | User Manual - Page 2
DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before beginning assembly. WEIDER is - Weider Pro 3750 | User Manual - Page 3
the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are adequately informed of all precautions. 3. The weight system is intended for home - Weider Pro 3750 | User Manual - Page 4
decal attached to the weight system (see the front cover of this manual). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. High Pulley Station Lat Bar Ab Pulley Station Backrests Decal 3 Decal 3 ASSEMBLED DIMENSIONS: Height: 78 in - Weider Pro 3750 | User Manual - Page 5
. You may want to assemble the weight system over a couple of evenings. Select a Location for the Weight System How to Identify Parts To help you identify the small parts used in assembly, we have included a PART IDENTIFICATION CHART in the center of this manual. Place the chart on the floor and - Weider Pro 3750 | User Manual - Page 6
on page 5. Refer to the PART IDENTIFICATION CHART in the center of this manual for help identifying small parts. 1 55 20 14 Locate and open the parts bags labeled "FRAME ASSEMBLY." Insert six M8 x 63mm Carriage Bolts (49) up through the Press Base (13) and the Weight Base (14). 2 Attach the - Weider Pro 3750 | User Manual - Page 7
M8 Nylon Locknuts (40). Do not tighten the Locknuts yet. 4 55 20 40 8 4 40 13 49 5. Insert two Weight Guides (23) into one of the 5 brackets on the Weight Base (14). Make sure the Weight Guides are oriented with the tall holes near the top (see the inset drawing). Attach the lower ends of - Weider Pro 3750 | User Manual - Page 8
Do not tighten the Locknuts yet. 10. Attach the upper ends of one set of Weight Guides (23) to the Top Frame (2) with an M8 x 152mm Bolt (67), two and an M8 Nylon Locknut (40). Attach the upper ends of the other set of Weight Guides (23) to the Top Frame (2) in the same manner. Tighten the M8 Nylon - Weider Pro 3750 | User Manual - Page 9
11. Locate and open the parts bag labeled "ARM ASSEMBLY." Attach the Leg Press Plate (11) to the Adjustment Tube (10) with an M8 x 60mm Bolt (62), two M8 Washers (20), and an M8 Nylon - Weider Pro 3750 | User Manual - Page 10
indicated bracket on the Butterfly Frame (3). IMPORTANT NOTE: Before assembling the 25mm Retainers (45) used in this step, make sure that you thoroughly understand the step. The Retainers can be assembled only once. If they must be removed, you will need to order - Weider Pro 3750 | User Manual - Page 11
18 18. Locate and open the parts bags labeled "CABLE ASSEMBLY", "CABLES", and "PULLEYS." During steps 19 through 49, refer to the CABLE DIAGRAMS on pages 26 and 27 of this manual to verify proper cable routing. Before beginning this section, fully unwind the five cables and identify the cables - Weider Pro 3750 | User Manual - Page 12
31 50 End with two holes should be down 80 50 42 82 89 4 23. Note: The Left Fly Arm (6) is shown removed for easier part identification. 23 Attach the Butterfly Cable (89) to the Left Fly Arm (6) with an M8 x 22mm Shoulder Bolt (51) and an M8 Nylon Locknut (40 - Weider Pro 3750 | User Manual - Page 13
end of the Cable so that two threads show past 68 the Locknut (see the inset drawing). Attach the Small "U"-bracket (32) to the indicated Weight Tube (25) with an M8 x 45mm Bolt (68) and an M8 Nylon Locknut (40). 32 87 20 40 13 87 40 20 40 25 - Weider Pro 3750 | User Manual - Page 14
28. Identify the Press Cable (88)-this is the 28 longest Cable. Attach the end of the Press Cable to the Large "U"-bracket (84) with an M8 Nylon Locknut (40) and an M8 Washer (20). Do not completely tighten the Locknut. It should be threaded onto the end of the Cable so that two threads are - Weider Pro 3750 | User Manual - Page 15
31. Route the Press Cable (88) over a 90mm Pulley 31 (82). Attach the Pulley and a Cable Trap (80) to the lower hole in the Pulley Plates (31) with an M10 x 48mm Bolt (50) and the M10 Nylon Locknut (42). The Cable must be routed from the direction shown. Make sure that the Cable Trap is - Weider Pro 3750 | User Manual - Page 16
35. Route the Press Cable (88) over a 90mm Pulley 35 (82). Attach the Pulley and a Cable Trap (80) to the indicated hole in the Press Frame (12) with an M10 x 82mm Bolt (66), an M10 Washer (38), and an M10 Nylon Locknut (42). 66 88 38 12 82 42 80 36. Wrap the Press Cable (88) around a "V"- - Weider Pro 3750 | User Manual - Page 17
39. Note: The 90mm Pulley (82) used in this step 39 was attached in step 38. It is shown removed for easier part identification. Route the Press Cable (88) around the 90mm Pulley (82). Make sure that the Cable Trap (80) is turned to hold the Cable in - Weider Pro 3750 | User Manual - Page 18
the end of the Cable so that two threads show past the Locknut (see the inset drawing). Attach the Small "U"-bracket (32) to the indicated Weight Tube (25) with an M8 x 45mm Bolt (68) and an M8 Nylon Locknut (40). 46. Locate the Low Cable (86). Wrap the Low Cable over - Weider Pro 3750 | User Manual - Page 19
47. Wrap the Low Cable (86) around a 90mm Pulley 47 (82). Attach the Pulley and a Cable Trap (80) to the Ab Upright (1) with the M10 x 92mm Bolt (76) and an M10 Nylon Locknut (42). Make sure that the Cable Trap is in the indicated position. 48. Wrap the Low Cable (86) over a 90mm Pulley (82). - Weider Pro 3750 | User Manual - Page 20
50. Locate and open the parts bag labeled "SEAT ASSEMBLY." Attach the Small Backrest (18) to the Ab Upright (1) with two M6 x 63mm Machine Screws (64) and two M6 Washers (37). 18 1 37 64 51. - Weider Pro 3750 | User Manual - Page 21
of the remaining parts will be explained in ADJUSTMENTS, beginning on the following page. Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If - Weider Pro 3750 | User Manual - Page 22
ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments - Weider Pro 3750 | User Manual - Page 23
Ab Upright (1). Attach the Rear Seat Frame to the Ab Upright with the M8 x 70mm Carriage Bolt (77) and the Seat Knob (30). For some exercises, the Seat (17) must be removed. First, be sure that the chain is not attached to the leg lever (see ATTACHING THE LEG LEVER TO - Weider Pro 3750 | User Manual - Page 24
is the resistance for each butterfly arm. The actual resistance at each weight station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. WEIGHT PLATES PRESS ARM (lbs.) BUTTERFLY ARM (lbs.) LEG LEVER (lbs.) HIGH PULLEY - Weider Pro 3750 | User Manual - Page 25
and tighten all parts each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch - Weider Pro 3750 | User Manual - Page 26
). Use the diagrams to be sure that the cables have been assembled correctly. The starting and ending points of each cable have been each cable. IMPORTANT: If the cables have not been correctly routed, the weight system will not function properly and damage may occur. Press Cable (88) Low Cable - Weider Pro 3750 | User Manual - Page 27
High Cable (85) High Pulley-1 4 2 3 Weight Stack-5 Rear Cable (87) 1-Top Frame 3 2 4-Weight Stack 27 - Weider Pro 3750 | User Manual - Page 28
PART IDENTIFICATION CHART-Model No. WESY26331 R0904A M6 Nylon Locknut (44) M8 Nylon Locknut (40) M10 Nylon Locknut (42) M6 Washer (37) M8 Washer (20) M10 Washer (38) - Weider Pro 3750 | User Manual - Page 29
M10 x 195mm Bolt (52) M8 x 67mm Bolt (55) M8 x 63mm Carriage Bolt (49) M8 x 70mm Carriage Bolt (77) M8 x 69mm Shoulder Bolt (43) M10 x 80mm Bolt (71) M10 x 82mm Bolt (66) M10 x 92mm Bolt (76) M10 x 97mm Bolt (95) M10 x 120mm Bolt (74) M8 x 152mm Bolt (67) - Weider Pro 3750 | User Manual - Page 30
1 Butterfly Cable 90 16 Weight 91 2 M10 x 57mm Bolt 92 2 25mm Inner Cap 93 2 Weight Pin 94 2 Pulley Cover 95 1 M10 x 97mm Bolt 96 1 Handle # 1 User's Manual # 1 Exercise Guide # 2 Grease Packet Note: "#" indicates a non-illustrated part. Specifications are subject to - Weider Pro 3750 | User Manual - Page 31
EXPLODED DRAWING-Model No. WESY26331 R0904A 55 56 55 20 55 43 87 42 20 69 55 40 20 56 89 51 47 42 76 40 3 51 42 38 38 2 50 56 82 85 76 50 40 82 69 80 42 40 56 67 40 50 92 89 50 82 80 82 80 82 42 50 42 40 42 47 48 45 40 45 46 6 67 40 4 64 37 40 46 80 23 87 32 - Weider Pro 3750 | User Manual - Page 32
WEIDER® PRO 3750 weight system) 3. The SERIAL NUMBER of the product (see the front cover of this manual) 4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfac-
tion through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-877-992-5999
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY26331
Serial No.
Write the serial number in the space
above for future reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal (Under Seat)
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!