Viper 771XV Owner Manual

Viper 771XV Manual

Get Viper 771XV PDF manuals and user guides View all Viper 771XV manuals
Add to My Manuals
Save this manual to your list of manuals

Viper 771XV manual content summary:

  • Viper 771XV | Owner Manual - Page 1
    Model 771XV ➤Owner's Guide
  • Viper 771XV | Owner Manual - Page 2
    without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced
  • Viper 771XV | Owner Manual - Page 3
    DEALER'S PURCHASE PRICE OF THE UNIT LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE an implied warranty will last or the call Directed Customer Service at 1-800876-0800 liability whatsoever, including without limitation, liability for and address ➤ Type of alarm installed ➤ Year, make, model
  • Viper 771XV | Owner Manual - Page 4
    programming remote 12 using your system 13 warning! safety first 13 active arming 15 passive arming 16 multi-level security arming 17 arming while driving 18 disarming 19 high security disarm 20 disarming without a 2-way remote 20 silent mode 21 panic mode 22 Valet mode 22 remote start
  • Viper 771XV | Owner Manual - Page 5
    35 interpreting zone diagnostics 36 code hopping 36 high frequency 37 owner recognition 37 rapid resume logic 38 power saver mode 38 programming options 39 security & convenience expansions 42 glossary of terms 43 quick reference guide 47 2 © 2005 directed electronics-all rights reserved
  • Viper 771XV | Owner Manual - Page 6
    LED indicator light ➤ A push-button Valet switch ➤ Your warranty registration ➤ A shut-down toggle switch important information Congratulations on the purchase of your combination remote start alarm system. Due to the complexity of this system, it must be installed by an authorized dealer only
  • Viper 771XV | Owner Manual - Page 7
    out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. Make necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer. ➜ fcc/id notice This device complies with Part
  • Viper 771XV | Owner Manual - Page 8
    2-way remote diagram 2 3 1 4 5 6 8 7 standard remote configuration 1. Unlock/Lock Indicator (Orange) 2. Receive/Transmit Indicator (Green) 3. Remote Start/Auxiliary Indicator (Yellow) 4. Panic Indicator (Red) 5. Lock Button 6. Unlock Button 7. Remote Start Button 8.
  • Viper 771XV | Owner Manual - Page 9
    standard remote button configuration controls the Arm and Panic On/Off function. controls the Disarm and Panic Off function. controls Silent Mode™ and Auxiliary channel 2 output. controls the Remote Start function. and pressed together control the Timer mode. and pressed together control Turbo
  • Viper 771XV | Owner Manual - Page 10
    battery is low (and this feature is programmed On) the 2way remote will emit 2 long beeps 5-seconds after a transmission is completed. The 2 long beeps will repeat every 25 seconds up to 3 times (or until a 2-way remote button is pressed). Battery Replacement Gently pull the end of the battery door
  • Viper 771XV | Owner Manual - Page 11
    the instructions in this manual correspond to a Standard Configuration 2-way remote. ➜ standard configuration Button The arming function is controlled by pressing this button for one second. Pressing and holding this button for more than 3-seconds will trigger the panic mode. Button The disarming
  • Viper 771XV | Owner Manual - Page 12
    feature is turned On/Off by pressing this button twice. and Buttons The remote start timer mode function of the system is controlled by pressing these buttons simultaneously. and Buttons The Turbo/Short Run feature is controlled by these buttons (refer to the Turbo/Short Run section for additional
  • Viper 771XV | Owner Manual - Page 13
    of a command or alarm system status. When the remote control receives a page it will generate a page notification to the user (notifications are audible beeps) and the LED Icons will display the current system status. Command Page When a command (arm/disarm, remote start, or auxiliary channel
  • Viper 771XV | Owner Manual - Page 14
    you to recognize the violation. Briefly press the button on the 2-way remote while the 2-way remote is beeping to clear the alarm page. If the alarm page was not cleared the 2-way remote will notify again at another 100 seconds. important! The Alarm Page alert can only be cleared during notification
  • Viper 771XV | Owner Manual - Page 15
    responds with 2 sets of 3 quick beeps and the Green LED will flash 6-times. programming remote To enter programming mode Press and hold all four remote control buttons simultaneously until one long beep is heard. Programming mode is now entered. Beeps On/Off Press to select beeps On/Off. One
  • Viper 771XV | Owner Manual - Page 16
    way remote control. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed
  • Viper 771XV | Owner Manual - Page 17
    the Safety Check outlined in the product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the authorized Directed dealer to fix the problem. ➤ After the remote start module has been installed, contact your authorized dealer to have him
  • Viper 771XV | Owner Manual - Page 18
    OF AN AUTHORIZED DIRECTED DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. ➜ active arming You can arm the system by pressing of your 2-way remote for one second. When the system arms, from the
  • Viper 771XV | Owner Manual - Page 19
    parking lights will flash to indicate that the system is armed. The remote responds to passive arming with one beep and the Orange LED will flash 3-times ) is open, the system will not passively arm (unless forced passive arming is programmed on. See Programming Options section.) Additionally, each
  • Viper 771XV | Owner Manual - Page 20
    will immediately start chirping the siren and flashing the parking lights. Three seconds later, the siren output changes to a continuous blast. This progressive response gives you time to disarm the system with your 2-way remote alarm system will immediately send an alarm page to your remote
  • Viper 771XV | Owner Manual - Page 21
    press on the 2-way remote for two seconds while the vehicle is running. The siren will chirp once to indicate will not respond to any input except the door triggers, and the starter kill relay (if installed) will not be activated. Once you have arrived at your destination, the system can be disarmed
  • Viper 771XV | Owner Manual - Page 22
    is described in the Diagnostics Section of this guide. The remote will indicate disarm notification with 2 beeps and 3 flashes of the Orange LED. If disarming after the system has been triggered, the remote control will send a diagnostic notification as a reminder. These diagnostic notifications
  • Viper 771XV | Owner Manual - Page 23
    after trigger. The 2-way remote will respond with a number of beeps and LED flashes according to whether a pinswitch, sensor, activated the alarm (and also if NPC is active). ➜ disarming without a 2-way remote If your 2-way remote is lost or damaged, you can manually disarm your vehicle security
  • Viper 771XV | Owner Manual - Page 24
    try again. Location of Valet Button Number of Presses important! The Valet® button can be programmed to respond to 1-5 presses for the disarm function. You must check with the installer to verify the programming for your individual unit. The remote will indicate disarm notification with 2 beeps
  • Viper 771XV | Owner Manual - Page 25
    responds with the normal arm/disarm notifications in silent mode. (If the remote has beeps programmed On, the remote will beep.) ➜ panic mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your 2-way remote. Just press for 3-seconds, and
  • Viper 771XV | Owner Manual - Page 26
    in-vehicle status LED will light solidly if you are entering Valet Mode, and it will go out if you are exiting Valet Mode. The remote responds with the normal arm/disarm notifications with each remote button press. ➜ remote start This feature allows you to remotely start and run your vehicle for
  • Viper 771XV | Owner Manual - Page 27
    has ended. 4. Once the vehicle has started, it will run for the pre-programmed period of time (either 12, 24, or 60 minutes - see Programming Options section of this guide) or until a shutdown input is triggered. For a remote start, the remote responds with remote start tones and the Yellow LED
  • Viper 771XV | Owner Manual - Page 28
    . ➤ The hood is opened. ➤ The shutdown toggle button is put into the OFF position. ➤ The pre-programmed run time (12, 24, or 60 minutes) has elapsed. ➤ 2-way remote button is pressed twice again to stop the vehicle. ➤ The remote responds with remote start off tones and the Yellow LED flashes 3-times
  • Viper 771XV | Owner Manual - Page 29
    . Then wait five seconds. 2. Turn the ignition key to the OFF position. (The engine will stay running.) 3. The engine will run until the pre-programmed time elapses or a shut-down input is received. (See the previous Remote Start section for a complete list of shut-down inputs.) note: This feature
  • Viper 771XV | Owner Manual - Page 30
    secure the vehicle. 7. The engine will turn off after the programmed run time. The remote responds with remote start tones and the Yellow LED illuminates for 3-seconds. ➜ timer mode By pressing the remote and buttons the parking lights will flash 4 times and then start the vehicle and run for
  • Viper 771XV | Owner Manual - Page 31
    4. The system will start the car and will run for the specified duration, unless shut down by the remote start button . 5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires. On entering Timer Mode the remote will respond with the Start On
  • Viper 771XV | Owner Manual - Page 32
    once again activate when the vehicle is remote started. note: If the remote start is on the lights will turn off then flash 3-times before returning to their normal output and the defogger output will activate as programmed.. Auxiliary Outputs (Options) This system also supplies outputs that
  • Viper 771XV | Owner Manual - Page 33
    damage to the starter motor if the key is turned to the start position during remote start operation. note: Anti-grind circuitry only works when the remote start system is operating the motor and the Failsafe® Starter Kill relay is installed. 30 © 2005 directed electronics-all rights reserved
  • Viper 771XV | Owner Manual - Page 34
    to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the shutdown toggle switch to the OFF position. The switch can be installed in a location of your choice. Check
  • Viper 771XV | Owner Manual - Page 35
    pedal will shut down the motor at any time during remote start operation, as well as preventing the remote start from activating while and each time the same sensor or switch triggers the alarm, NPC will interpret those triggers as false alarms. After the third trigger, NPC ignores, or bypasses,
  • Viper 771XV | Owner Manual - Page 36
    disarming the system does not reset this function! The only ways to reset a bypassed zone are for it to not trigger for 60 minutes, or to turn on the ignition. If testing your system, it is important to remember that the NPC programming microprocessor will also of this guide for diagnostic
  • Viper 771XV | Owner Manual - Page 37
    its memory and chirp four or five times each time it is disarmed, until the next time that the ignition is turned on. ➜ system status chirps The siren will chirp when arming/disarming the system. The pattern of chirps will audibly report the system's status as described below. 34 © 2005 directed
  • Viper 771XV | Owner Manual - Page 38
    System armed System armed with Bypass Notification System disarmed System disarmed with Tamper Alert System disarmed NPC active ➜ table of zones A zone sensors or switches that have been installed. ZONE (Number of LED Flashes) DESCRIPTION DEALER-INSTALLED OPTIONS 1 Instant trigger - trunk
  • Viper 771XV | Owner Manual - Page 39
    disarming diagnostics. If you receive a Bypass notification when arming or a Tamper Alert notification when disarming, look at the LED in the car. Active or triggered zones will and 2-way remotes use a mathematical formula called an algorithm to change their code each time the 2-way remote is used
  • Viper 771XV | Owner Manual - Page 40
    assigned to that 2-way remote. Owner Recognition lets up to four users of the system have different settings that meet their specific needs. It is almost like having four separate alarms in your vehicle, one for each user. note: Owner Recognition cannot be programmed without a Bitwriter and the
  • Viper 771XV | Owner Manual - Page 41
    is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the system including arm, disarm, and Valet Mode. power saver mode Your system will automatically enter Power Saver Mode while armed or
  • Viper 771XV | Owner Manual - Page 42
    Bold. ➤ Active arming (2-way remote only) or passive arming (automatic arming 30 seconds after the last door has been closed). ➤ Arming/disarming siren chirps on or off. ➤ The ignition controlled door lock feature on or off: When this feature is programmed on, the doors will lock three seconds after
  • Viper 771XV | Owner Manual - Page 43
    nuisance. If your installer is programming the security system with the Directed Bitwriter, the full triggered response can be programmed for any duration regardless of whether or not the alarm is armed. If AED is programmed on, the starter of the vehicle will be disabled 30 seconds after the
  • Viper 771XV | Owner Manual - Page 44
    . Thirty seconds later, the starter will be disabled. To start the car, it will be necessary to disarm the system with the 2-way remote. It is also possible to disarm the AED feature by turning the ignition key to the RUN position and pressing the Valet button the programmed number of times. AED is
  • Viper 771XV | Owner Manual - Page 45
    : Prevents the vehicle's hood from being opened without a key, keeping thieves away from the system's siren, the battery connections, and other components under the hood. Field Disturbance Sensor: An invisible dome of coverage is established by installing the 508D "radar" sensor. Your system can
  • Viper 771XV | Owner Manual - Page 46
    on-screen security system programming and zone trigger information. glossary of terms 2-Way Remote: Hand-held, 2-way transceiver which operates the The vehicle is never prevented from cranking when the system is disarmed, in Valet Mode, or if the starter interrupt switch itself fails. Your
  • Viper 771XV | Owner Manual - Page 47
    the programmed duration. Valet Button: A small push button switch mounted at a discretionary location inside the vehicle. It is used to override the starter interrupt when a 2-way remote is lost or damaged, or to enter or exit Valet Mode. Warning Zone Response: Lighter impacts to the vehicle will
  • Viper 771XV | Owner Manual - Page 48
    Zone: A zone is a separate input that the alarm can recognize as unique. Each input to the system is connected to a particular zone. Often two or more inputs may share the same zone. © 2005 directed electronics-all rights reserved 45
  • Viper 771XV | Owner Manual - Page 49
    46 © 2005 directed electronics-all rights reserved
  • Viper 771XV | Owner Manual - Page 50
    ) and the vehicle will start and run for the programmed period of time. To disable the remote start system ■ To disable the remote start, move the shutdown toggle switch to the OFF position. Location of Valet® button Number of Valet® button pulses for disarming © 2005 directed electronics
  • Viper 771XV | Owner Manual - Page 51
    the OFF position. Once the vehicle has started, it will run for the pre-programmed period of time (12, 24, or 60 minutes). Rear Window Defogger ■ Press the , , and buttons simultaneously to turn the defogger on or off when remote start- ing. When a remote start is initiated, the parking lights
  • Viper 771XV | Owner Manual - Page 52
    to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly information about our products and services. Directed Electronics is committed to delivering world class quality products and services that excite and delight our
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Model 771XV
➤
Owner’s Guide