Viper 5704 Owner Manual

Viper 5704 Manual

Get Viper 5704 PDF manuals and user guides View all Viper 5704 manuals
Add to My Manuals
Save this manual to your list of manuals

Viper 5704 manual content summary:

  • Viper 5704 | Owner Manual - Page 1
  • Viper 5704 | Owner Manual - Page 2
    purchase of your state-of-the-art security and remote start system. Reading this Owner's Guide prior to using your system will help maximize the use of your system and its many features. Please visit: www.viper.com - For general and additional guide information. For any additional questions please
  • Viper 5704 | Owner Manual - Page 3
    registration card. Replacement remote controls If additional remote controls are desired, please see your authorized dealer or visit us at www.directedstore.com to order. Part numbers are: 7752V for Responder LC 2-way remote control and 7652V for the companion remote control. Your system can also
  • Viper 5704 | Owner Manual - Page 4
    Contents Getting Started...4 Charging the remote control 4 Keys to using this manual 5 Responder LC 2-Way 6 Status Screen Icons 8 Using your System 11 Commands and Confirmations 11 Performing Commands 11 Responder LC Command table 12 Fault Condition Alerts 12 Basic commands (Direct Access
  • Viper 5704 | Owner Manual - Page 5
    Main Menu...24 Setup Remote menu 24 Remote Start Info 25 Runtime Alert 26 Car 2 26 Screen Color 26 Temp Unit 26 Button Beep 27 System Type 27 Clock Set 27 Review 27 Exit 27 Sensor Adjust 27 Pair Remote 28 Demo mode 28 Power Off 29 Exit 29 Alarm Features 30 Normal Arm Protection 30
  • Viper 5704 | Owner Manual - Page 6
    (1-Way 46 System Expansion Options 47 Battery Information (Responder LC 49 Low Battery 49 Battery Life 50 Battery Disposal 51 Glossary of Terms 52 Government Regulations 54 Warning! Safety First 56 Installation 56 Remote Start Capable 56 Manual Transmission Vehicles 56 Interference
  • Viper 5704 | Owner Manual - Page 7
    mini-USB port located on the side of the remote control (see diagram under Responder LC 2-way). The text field will display CHARGE to indicate the remote control is charging (The remote remains operational while charging and can command the system). 2. Once fully charged the text field will display
  • Viper 5704 | Owner Manual - Page 8
    At a Glance Keys to using this manual Specific actions (in bold type) and style conventions are used consistently throughout this manual, they are as follows: s
  • Viper 5704 | Owner Manual - Page 9
    the display contains status icons for the System, Siren, Alarm zones, Remote Start and Remote Control. Text field - the lower portion of display - shows the Clock, Runtime or Temperature during Remote Start, as well as Command confirmations, Page messages and programming menus Used to perform arming
  • Viper 5704 | Owner Manual - Page 10
    At a Glance Control Center Status LED Control button The Control Center, typically located on the upper part of the front windshield sends and receives commands or messages to and from your system. It consists of: s
  • Viper 5704 | Owner Manual - Page 11
    Status + ALL Unlocked: The system is Unlocked in Valet, the alarm is disabled. Siren is disabled for sensor triggers; remote is paged for all triggers (Sensor Silent Arm). Siren is disabled for all triggers; remote is paged for all triggers (Full Silent Arm). Remote start is active, the engine is
  • Viper 5704 | Owner Manual - Page 12
    Start is On; Remote Start is Off. Manual Transmission Start mode is enabled, the engine can be started Displays the vehicle interior temperature Remote Start On during Remote Start remote is set to command the system programmed as Car 1* On when remote is set to command the system programmed as
  • Viper 5704 | Owner Manual - Page 13
    are received Displays the Clock, Runtime, Temperature, message text and feature menus On after the Garage Open** message has been received. On after the Garage Closed** message has been received. * This icon not present until the Car 2 is turned on in the Setup Remote configuration menu. ** This
  • Viper 5704 | Owner Manual - Page 14
    , Basic or Advanced, are used to activate system features and are performed by pressing one of the Command buttons. Basic commands control the most often used security and remote start features while Advanced commands control more specialized features and request reports. Confirmations for Basic or
  • Viper 5704 | Owner Manual - Page 15
    Car (3s), Enter programming (8s) Temperature Check Runtime Remaining Alarm Report Fault Condition Alerts If, when performing a command, a condition exists that does not allow activation of an Alarm feature* or Remote Start feature**, the NOT AVAILABLE or REMOTE START ERROR text and a fault
  • Viper 5704 | Owner Manual - Page 16
    ** Remote Start feature not available when the Remote Start status is incorrect upon receiving the command. (Example: Runtime reset command received when remote start is off) Refer to the notes included in the command descriptions that address these faults or go to "Remote Start Error" on page 39
  • Viper 5704 | Owner Manual - Page 17
    and beeps play to confirm and the system status icons update. If Valet mode* is On, the doors unlock and the VALET text and tone play. More than 2 siren chirps and remote beeps indicate a trigger has occurred. The DISARM text is replaced by the Alarm report.** 14 © 2011 Directed Electronics. All
  • Viper 5704 | Owner Manual - Page 18
    will display the Runtime, Temperature or Clock as programmed. If Remote Start fails to activate, REMOTE START ERROR text and a fault tone play while the parking lights flash to identify the reason.*** * See "Remote and System Operations" on page 40 for details. ** See "Alarm Features" on page 30 for
  • Viper 5704 | Owner Manual - Page 19
    . Valet mode* or Trigger Zone Fault report** messages may be received. Silent Disarm Press and release The alarm disarms, doors unlock (if connected), and the parking lights flash twice. The SILENT DISARM text plays to confirm and the System Status icons update. The Alarm report** may replace the
  • Viper 5704 | Owner Manual - Page 20
    reset will reset the runtime counter to the pre-programmed setting. The RUNTIME text and tones play to confirm. The text field will update if set to display runtime. Note Remote Start must be On to use this feature. Temp Request Press and hold the button Requests the vehicle's interior temperature
  • Viper 5704 | Owner Manual - Page 21
    bypass is Off, BYPASS OFF and 1beep play to confirm.. Note System needs to be armed to perform Sensor Bypass. Perform arm command any time to turn Sensor Bypass Off. Remote Valet Press and release Enters (or if On, exits) Valet Mode. The VALET text and beeps (1 for On, 2 for Off) play to confirm and
  • Viper 5704 | Owner Manual - Page 22
    the Remote start status icons update. Note System needs to be armed or Timer Start will not start the engine. Runtime Remaining Press and hold the button Requests the remaining Remote start runtime and temporarily displays it in the text field. Note Remote Start must be On to use this feature. * See
  • Viper 5704 | Owner Manual - Page 23
    Commands: (Level 3) Press and release the button 3 times. Sensor Silent Arm* Press and release level 3 The alarm arms, doors lock, the siren chirps and parking lights flash 3 times. The SENSOR SILENT ARM text and beeps play to confirm and the System and Siren Status icons update. Car finder Press
  • Viper 5704 | Owner Manual - Page 24
    START ON or SMART START OFF text and beeps play to confirm and the Remote start status icons update. Note System needs to be armed or Smart Start will not start the engine. Alarm is turned on. * See "Alarm Features" on page 30 for more details. ** See "Advanced Start" on page 35 for more details
  • Viper 5704 | Owner Manual - Page 25
    circuit will also automatically activate 10 seconds after remote starting if the temperature is below 55°F. Note Remote Start must be active to use this feature. * See "Alarm Features" on page 30 for more details. ** This feature must be installed and turned on by an authorized Directed dealer
  • Viper 5704 | Owner Manual - Page 26
    Configurations Operations of the Responder LC and how it communicates messages are set in the configuration Main Menu. Navigating menus and options Navigating menus and features, changing options, and exiting are performed using the remote control buttons. The following instructions discuss how to
  • Viper 5704 | Owner Manual - Page 27
    Menu The following Main Menu list of features is available for configuration of the remote control. Setup Remote menu: Keypad Lock Options: OFF , AUTO When OFF , the buttons do not lock and always perform a command when pressed. When set to AUTO , the remote buttons lock after a 20 second lapse
  • Viper 5704 | Owner Manual - Page 28
    ONLY when you don't want to be interrupted. Remote Start Info Options: RUNTIME , TEMP , CLOCK The text field can be set to display the information you prefer during remote start. RUNTIME : Remote Start Runtime, TEMP : vehicle interior Temperature, or the CLOCK will be displayed in the text field while
  • Viper 5704 | Owner Manual - Page 29
    Car 2 Options: OFF , ON , HOME This remote can control two systems independently. When set to OFF , the Car2 select option is not available. When set to ON the remote can be set to control 2 systems. The HOME option is for pairing to a home security system. Screen Color Options: OFF , WHITE ,LT GRN
  • Viper 5704 | Owner Manual - Page 30
    the remote has been paired, and adjusts the text and main menu accordingly. This has been pre-set by the factory for your system. Clock Set Options: HOUR , MIN Review Displays firmware version Exit Exits and returns to the main menu Sensor Adjust: If you feel your security system shock sensor is
  • Viper 5704 | Owner Manual - Page 31
    Pair Remote: Remote Pair is a process where the Responder LC and the system in the vehicle learn each others encrypted identification, securing their communication from intruders. Please note that your remote controls come pre-programmed from the factory. Prepare the vehicle system to be Paired with
  • Viper 5704 | Owner Manual - Page 32
    Demo mode: Demo Mode plays a pre-selected group of animations as a demonstration tool to show friends or family. Running Demo mode shortens the battery life over time if used excessively s
  • Viper 5704 | Owner Manual - Page 33
    Alarm Features Normal Arm Protection Status LED: The Control Center Status LED flashes as a visual indicator that your vehicle's security system is active. Starter Kill: The Failsafe starter kill relay prevents the engine from starting Note May require additional parts and installation Sensor
  • Viper 5704 | Owner Manual - Page 34
    ). 3. After a few seconds the siren output ceases and the system is disarmed. Feature Details Note As a precaution, if programmed for Passive Arming or Auto re-arming the system should be placed into Valet Mode until a remote is available . © 2011 Directed Electronics. All rights reserved. 31
  • Viper 5704 | Owner Manual - Page 35
    remote command the system runs a status check of the alarm trigger zones. Faulty zones (usually caused by dome light delay or open trunk) are bypassed and reported via the control center LED and remote Table of Zones). The DISARM text is replaced by ALARM REPORT and text identifying the triggers. *
  • Viper 5704 | Owner Manual - Page 36
    Zone # (led flashes) 1 2 3 4 5 6 Table of Zones Zone Name Trunk Shock Sensor Door Sensor 2 Ignition Hood Alarm Report when requested The Alarm Report displays the two most recent alarm triggers depending on the system state when requested. When disarmed, the report will display text to identify
  • Viper 5704 | Owner Manual - Page 37
    turn on and the REMOTE START ON message will play on the remote control. 3. Turn the key to off, and remove it from the ignition, the engine continues running for the programmed runtime. 4. Exit the vehicle and arm the alarm. Note For Pit Stop on manual transmission vehicles follow the directions
  • Viper 5704 | Owner Manual - Page 38
    is attempted while Off, the engine will not start. (See "Remote Start Error" on page 39) move the switch back to the On position to resume normal operation. Advanced Start The Advanced start features Timer Start and Smart Start will automatically start the engine to maintain battery charge or combat
  • Viper 5704 | Owner Manual - Page 39
    is sent to the remote control and the countdown timer restarts. This will repeat as many times as set by the installer (default 6 starts). Timer Start is exited after the final start. Smart Start operation Smart Start uses the settings for Timer Start in addition to temperature and battery level to
  • Viper 5704 | Owner Manual - Page 40
    installed into a manual transmission vehicle, the system requires that the MTS mode is properly set when parking. If MTS mode is not properly set or is defeated after being properly set the system will not start the engine and the REMOTE START ERROR text and tones play as an alert. Feature Details
  • Viper 5704 | Owner Manual - Page 41
    3 then the engine continues to run. Turbo Timer Mode The system keeps the engine running for the Turbo Timer runtime and can be activated by remote control or optional dash mounted activation button. 1. With the engine running, set the parking brake. 2. Press the optional dash mounted activation
  • Viper 5704 | Owner Manual - Page 42
    Remote Start Error For user safety, the system must be properly configured or remote start will not activate. Refer to the table below for the screens and parking light flashes that will identify the configuration issue and resolution. Flashes * 5 6 7 Possible Fault Brake on Hood open After
  • Viper 5704 | Owner Manual - Page 43
    secure in case of accidental disarming the system, if a door is not opened within 30 seconds the system re-arms itself and locks the doors. Auto Re-arming* Auto re-arm ensures the vehicle stays protected if it is not entered after disarming by remote control. After disarming by remote, the alarm
  • Viper 5704 | Owner Manual - Page 44
    Valet Mode Valet mode can be entered and exited by performing the Remote Valet command or manually using the vehicle key and the control button. When entered, the alarm functions are defeated while the convenience features still operate normally. Arm and Disarm commands lock and unlock the doors
  • Viper 5704 | Owner Manual - Page 45
    to return to normal operation. Feature not Available The NOT AVAILABLE message is a generic one which varies in cause and solution depending upon the command used: Command Cause Runtime Reset Remote Start is Off Sensor Bypass System is not armed Defroster Remote Start is Off. Not configured
  • Viper 5704 | Owner Manual - Page 46
    Arm/Lock (Panic) Disarm/ Unlock Remote Start A U X Aux/Trunk x 1 LEVEL 1 Silent Arm x 2 LEVEL 2 Sensor Bypass x 3 x 4 LEVEL 3 LEVEL 4 Sensor Silent Full Silent Arm Arm Silent Disarm Remote Valet Car Finder Runtime Reset AUX 1 Timer Start Smart Start Defogger AUX 2 AUX 3 AUX 4 Not
  • Viper 5704 | Owner Manual - Page 47
    remote The companion 1 way remote commands the system features as shown in the previous table, but without the message display of the Responder LC remote turned On (See Remote Features menu under "Programming" on page 45 to turn on). Press and hold the button for 3 seconds. The remote flashes the LED
  • Viper 5704 | Owner Manual - Page 48
    used for sensor adjustment, to avoid unintended alarm triggers, it is recommenced that an authorized Directed dealer perform all sensor adjustments. Remote Features menu Press and release the button, 2 LED flashes and beeps indicate the remote features menu is accessed and can be set. Press buttons
  • Viper 5704 | Owner Manual - Page 49
    the cover indicates the direction), remove the cover from the remote control housing. + 2. Gently pry up on the battery to re- move it from the holder. Insert a new battery into the holder and under the clip with the positive (+) side up. Replace the battery cover. The re- mote control is now
  • Viper 5704 | Owner Manual - Page 50
    details. Owner recognition The system can be configured to recognize the remote used when disarming and change selected features to match the remote users preferences. Memory seat adjustment, siren chirps, passive arming, remote button auto unlocking, alarm output duration can all be custom set for
  • Viper 5704 | Owner Manual - Page 51
    Channels The Auxiliary Channel outputs of this system can activate many of the convenience features found in today's vehicles. Once a command is performed to activate a convenience feature the Responder LC displays text that matches the feature. The system installer can clarify if any of the below
  • Viper 5704 | Owner Manual - Page 52
    battery's life and usage in providing your Responder LC remote control with many years of trouble free operation. The battery information for the 1way companion remote control can be found in the 1-way Companion Remote Control section of this manual. Warnings! NEVER connect the supplied AC adapter
  • Viper 5704 | Owner Manual - Page 53
    can be charged. Battery Life The Responder LC remote control has many features that make it one of the most unique remote controls on the market today, including superior long range communication with the system. The default feature settings provide for excellent battery charge duration. However
  • Viper 5704 | Owner Manual - Page 54
    Battery Disposal Directed Electronics cares about the environment. If you need to dispose of the battery, please do so in accordance with your municipal requirements for battery disposal. Battery © 2011 Directed Electronics. All rights reserved. 51
  • Viper 5704 | Owner Manual - Page 55
    indicate the status of your system. It is located on your system's Control Center. Control Button A small push button located on your system's control center. It is used to override (disarm) the alarm when a remote is not available or to enter or exit Valet Mode. 52 © 2011 Directed Electronics
  • Viper 5704 | Owner Manual - Page 56
    is covered by one or more of the following United States patents: Remote Start Patents: 5,349,931; 5,872,519; 5,914,667; 5,952,933; 5,945,936; 5,990,786; 6,028,372; 6,467,448; 6,561,151; 7,191,053; 7,483,783 Vehicle Security Patents: 5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591; 5,650
  • Viper 5704 | Owner Manual - Page 57
    to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However
  • Viper 5704 | Owner Manual - Page 58
    FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of 20 cm or more used if it is determined that it causes harmful interference to services authorized by IC. In addition, the user of this device must accept any radio interference that may be
  • Viper 5704 | Owner Manual - Page 59
    without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed menu wheel. It is the user's sole responsibility to properly handle and keep out of reach from children all
  • Viper 5704 | Owner Manual - Page 60
    Before remote starting a manual transmission vehicle, be sure to: s
  • Viper 5704 | Owner Manual - Page 61
    OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. This product is designed for fuel injected vehicles only. Use of this product in a standard transmission vehicle must be in strict accordance with this guide. This
  • Viper 5704 | Owner Manual - Page 62
    replace (at Directed's election) with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors , neglect, improper service, installation or other causes not INSTALLERS. DIRECTED SECURITY SYSTEMS
  • Viper 5704 | Owner Manual - Page 63
    AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT , ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES NOT ARISING OUT OF Directed products, please visit the support section of Directed's website at:
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63