Viper 5701 Owner Manual

Viper 5701 Manual

Get Viper 5701 PDF manuals and user guides View all Viper 5701 manuals
Add to My Manuals
Save this manual to your list of manuals

Viper 5701 manual content summary:

  • Viper 5701 | Owner Manual - Page 1
    Viper® Auto Security Systems is Directed Electronics. Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security is committed to delivering world class quality products and services that excite and delight our customers. O W N E R' S G U
  • Viper 5701 | Owner Manual - Page 2
    state-of-the-art remote start and security system. Reading this Owner's Guide prior to using your system will help maximize the use of your system and its many features. For more information please visit the below website: http://www.viper.com - For general and additional guide information. For any
  • Viper 5701 | Owner Manual - Page 3
    card with you to reference your system's many features. Replacement remote controls If additional remote controls are desired, please see your authorized dealer or visit us at www.directedstore.com to order. Part numbers are: 7251V for Responder LE 2-way remote control and 7152V for the companion
  • Viper 5701 | Owner Manual - Page 4
    ...4 Keys to using this manual 4 Responder LE 2-Way 5 Using your System 7 Commands and Confirmations 7 Performing Commands 7 Remote Control Command table 8 Fault Condition Alerts 8 Basic Commands (Direct Access 10 Arm 10 Disarm 10 Remote Start 11 AUX/Trunk 11 Advanced Commands: (Level
  • Viper 5701 | Owner Manual - Page 5
    28 Remote Start Safe-lock 29 Disabling Remote Start 29 Advanced Start 29 Temperature Reporting 30 Remote Start Time-out Alert 31 Manual Transmission Start (MTS mode 31 Turbo Timer Mode 32 Remote Start Faults 32 Remote and System Operations 34 Passive Arming 34 Auto Re-arming 34 Valet Mode
  • Viper 5701 | Owner Manual - Page 6
    Warning! Safety First 46 Installation 46 Remote Start Capable 46 Manual Transmission Vehicles 46 Interference 48 Upgrades 48 Water/Heat Resistance 48 Limited lifetime consumer warranty 49
  • Viper 5701 | Owner Manual - Page 7
    Getting Started Keys to using this manual Specific actions (in bold type) and style conventions are used consistently throughout this manual, they are as follows: s
  • Viper 5701 | Owner Manual - Page 8
    it that are active during related operations. These LED's are labeled respectively as: Arm LED, Disarm LED, Remote Start LED, Aux LED, and LED * 2-way communication is only applicable to the Responder LE remote control ** Term denotes that these LED's are only visible when On (Ghost LED's are only
  • Viper 5701 | Owner Manual - Page 9
    Control Center Control button Status LED The Control Center, typically located on the upper part of the front windshield sends and receives commands or messages to and from your system. It consists of: s
  • Viper 5701 | Owner Manual - Page 10
    Commands, Basic or Advanced, are used to activate system features and are performed by pressing one of the Command buttons. Basic commands control the most often used security and remote start features while Advanced commands control more specialized features and request reports. Confirmations for
  • Viper 5701 | Owner Manual - Page 11
    Disarm Remote Valet Car Finder Remote Start AUX Aux/Trunk Runtime Reset AUX 1 Timer Start Smart Start Defogger AUX 2 AUX 3 AUX 4 Advance Level, Change Car (3 sec), Enter programming (8 sec) Temperature Check* Arm Status* Runtime Remaining* *Not available for 1-way companion remote control
  • Viper 5701 | Owner Manual - Page 12
    is incorrect upon receiving the command. (Example: Runtime reset command received when remote start is off). Refer to the notes included in the command descriptions that address these faults or go to Remote Start Faults under the Remote Start Features section for more details. © 2011 Directed
  • Viper 5701 | Owner Manual - Page 13
    and the siren chirps and parking lights flash twice. The Disarm LED and beeps play to confirm. If Valet mode* is On, the doors unlock and the Disarm LED, LED and fault tones play. An Alarm Report** will replace the disarm output if the alarm was 10 © 2011 Directed Electronics. All rights reserved.
  • Viper 5701 | Owner Manual - Page 14
    play to confirm. * See Remote and System Operations for details. ** See Alarm Features for details. *** See Remote Start Faults (under Remote Start Features) for details. For Manual transmission vehicles see Manual Transmission Start in the Remote Start Features section for more details. © 2011
  • Viper 5701 | Owner Manual - Page 15
    LED turns on to confirm. The Silent Disarm output may be replaced by the Alarm Report** Runtime Reset Press and release If more time is needed while remote start is active, runtime reset will reset the runtime counter to the pre-programmed setting. The green ghost LED's show the runtime and the
  • Viper 5701 | Owner Manual - Page 16
    button Requests the vehicle's interior temperature and displays it by illuminating the green ghost LED's; cold is 1 LED, cool (2), warm (3), warmer (4) . * See Remote and System Operations section for details. ** See Alarm Features for details. © 2011 Directed Electronics. All rights reserved. 13
  • Viper 5701 | Owner Manual - Page 17
    Advanced Commands: (Level 2) Press and release the button 2 times. The nate indicating Level 2 and Aux LED's illumi- Sensor Bypass Press and release Performing the Sensor Bypass command will incrementally bypass sensor operations and be confirmed as follows: s
  • Viper 5701 | Owner Manual - Page 18
    the systems Arm Status since its last update message or command operation. It will report status via ghost LED's, beeps, and tones as described in this section for Arm, Disarm, Valet mode arm, Valet mode disarm, Sensor Silent arm, Full Silent arm. * See Advance Start under Remote Start Features
  • Viper 5701 | Owner Manual - Page 19
    parking light flashes stop if armed or disarmed while Car Finder is in progress. Smart Start** Press and release Activates (or if On, deactivates) Smart Start. The parking lights flash quickly five times for On and slowly five times for Off. The Remote Start LED and beeps play (1 for on, 2 for off) to
  • Viper 5701 | Owner Manual - Page 20
    Aux 3 output. The Aux LED and On tones or Off tones play to confirm. Runtime Remaining Press and hold the button Requests the remaining Remote start runtime and temporarily displays it in 4 increments using the green Ghost LED's. Example for 12 minute runtime: s
  • Viper 5701 | Owner Manual - Page 21
    Press and release the button 4 times. The and Disarm LED's illuminate indicating Level 4 , Aux, Remote Start Full Silent Arm* Press and release The alarm arms, doors lock, and the siren chirps and parking lights flash 4 times. The Arm LED, 1 beep and 4 fault tones play to confirm. Defogger** Press
  • Viper 5701 | Owner Manual - Page 22
    Remote Control Configuration Remote Programming The Responder LE and 1-way companion remote controls have operations that can be configured to a user's personal preferences. The following instruction will direct you through the available programming options for both remotes. Enter programming, press
  • Viper 5701 | Owner Manual - Page 23
    s
  • Viper 5701 | Owner Manual - Page 24
    this message can be turned off by an authorized Directed Dealer. Page Mode Options: Power Save 1, Power Save 2, On, Off Paging is how the Responder LE remote monitors your system's messages. Power Save extends battery life by turning Paging Off after 72 © 2011 Directed Electronics. All rights
  • Viper 5701 | Owner Manual - Page 25
    wake up to receive remote start or alarm trigger pages. Note: When Off, responses are still received when a command is performed but alarm trigger pages will not be received. Car 2 Options: Off, On The Responder LE and 1-way companion remote controls can control two systems independently. When set
  • Viper 5701 | Owner Manual - Page 26
    Sensor Adjust The button is used for sensor adjustment, to avoid unintended alarm triggers; it is recommenced that an authorized Directed Dealer performs all sensor adjustments. © 2011 Directed Electronics. All rights reserved. 23
  • Viper 5701 | Owner Manual - Page 27
    LED: The Control Center Status LED flashes as a visual indicator that your vehicle's security system is active. Starter Kill: The Failsafe starter kill relay prevents the engine from starting Note May require additional parts and installation Sensor triggers: The onboard shock sensor can distinguish
  • Viper 5701 | Owner Manual - Page 28
    control button on the Control Center the correct number of times (the default is 1 press). 3. After a few seconds the siren output ceases and the system is disarmed. Note As a precaution, if programmed for Passive Arming or Auto re-arming the system should be placed into Valet Mode until a remote
  • Viper 5701 | Owner Manual - Page 29
    chirps as an audible alert, the control center LED flashes in groups to indicate the zone number. Alarm Report If the alarm was triggered while armed, it will be reported when the alarm is disarmed via the remote control, siren chirps, parking light and control center LED flashes. The siren chirps
  • Viper 5701 | Owner Manual - Page 30
    6 Table of Zones Zone Name Trunk Shock Sensor Door Sensor 2 Ignition Hood Nuisance Prevention (NPC) NPC monitors all alarm zones and, if any are triggered sensors automatically reset after one hour and after the vehicle is driven. Disarming then re-arming the alarm does not reset bypassed sensors
  • Viper 5701 | Owner Manual - Page 31
    on the remote control. 3. Turn the key to off, and remove it from the ignition, the engine continues running for the programmed runtime. 4. Exit the vehicle and arm the alarm. Note For Pit Stop on manual transmission vehicles follow the directions in the Manual Transmission Start (MTS mode) section
  • Viper 5701 | Owner Manual - Page 32
    the engine will not start. (See Remote Start Fault under Remote Start Features) move the switch back to the On position to resume normal operation. Advanced Start The Advanced start features; Timer Start and Smart Start will automatically start the engine to maintain battery charge or combat extreme
  • Viper 5701 | Owner Manual - Page 33
    remote control and the countdown timer restarts. This will repeat as many times as set by the installer (default 6 starts). Timer Start is exited after the final start. Smart Start operation Smart Start uses the settings for Timer Start in addition to temperature and battery level to automatically
  • Viper 5701 | Owner Manual - Page 34
    minute before the engine turns off. The LED, Remote Start LED flash and several tones play as an alert to reset the runtime if desired. Manual Transmission Start (MTS mode) When installed into a manual transmission vehicle, the system requires that the MTS mode is properly set when parking. If MTS
  • Viper 5701 | Owner Manual - Page 35
    the doors and arm the system. 6. The engine runs for the Turbo Mode runtime. Note Turbo Timer must be turned on by an authorized Directed dealer. Remote Start Faults For user safety, the system must be properly configured or remote start will not activate. The Remote Start Fault output ( LED on and
  • Viper 5701 | Owner Manual - Page 36
    Hood open After performing Remote Start command - MTS not enabled 8 None After performing Timer Start or Smart Start command Toggle Switch off Alarm is triggered Solution Release foot brake Close hood Enable MTS mode Check all Solutions Turn switch on Disarm or reset alarm * Refers to the number
  • Viper 5701 | Owner Manual - Page 37
    within 30 seconds the system re-arms itself and locks the doors. Auto Re-arming* Auto re-arm ensures the vehicle stays protected if it is not entered after disarming by remote control. After disarming by remote, the alarm automatically re-arms itself (and locks the doors if programmed on) in 30
  • Viper 5701 | Owner Manual - Page 38
    mode can be entered and exited by performing the Remote Valet command or manually using the vehicle key and the control button. When entered, the alarm functions are defeated while the convenience features still operate normally. Arm and Disarm commands lock and unlock the doors. The Responder LE
  • Viper 5701 | Owner Manual - Page 39
    used: Command Cause Runtime Reset Remote Start is Off Sensor Bypass System is not armed Defroster Remote Start is Off. Not configured for this. Reason/Solution Only available when Remote Start is On Only available when system is armed Only available when Remote Start is On. Only available
  • Viper 5701 | Owner Manual - Page 40
    rst be turned On (See Remote Control Configuration section to turn on). 1. Press and hold the button for 3 seconds. The remote flashes the LED and beeps once or twice to indicate the selected Car is 1 or 2. 2. Release the button for Car Select or continue to hold for programming. 3. Release the button
  • Viper 5701 | Owner Manual - Page 41
    See Owner Recognition following for details. Owner recognition The system can be configured to recognize the remote used when disarming and change selected features to match the remote users preferences. Memory seat adjustment, siren chirps, passive arming, remote button auto unlocking, alarm output
  • Viper 5701 | Owner Manual - Page 42
    Driver door priority unlocking The door unlocking operation can be configured to emulate an OEM style of driver priority unlocking for added security during disarming. © 2011 Directed Electronics. All rights reserved. 39
  • Viper 5701 | Owner Manual - Page 43
    If confirmation chirps are programmed off, the system will still emit one chirp as an alert when disarming. After performing a command, several beeps play on the Responder LE remote to indicate the battery/ batteries need replacing. Battery Life The Responder LE remote control has many features that
  • Viper 5701 | Owner Manual - Page 44
    s
  • Viper 5701 | Owner Manual - Page 45
    indicate the status of your system. It is located on your system's Control Center. Control Button A small push button located on your system's control center. It is used to override (disarm) the alarm when a remote is not available or to enter or exit Valet Mode. 42 © 2011 Directed Electronics
  • Viper 5701 | Owner Manual - Page 46
  • Viper 5701 | Owner Manual - Page 47
    to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However
  • Viper 5701 | Owner Manual - Page 48
    Control Center To satisfy FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of if it is determined that it causes harmful interference to services authorized by IC. In addition, the user of this device must accept any radio interference that may
  • Viper 5701 | Owner Manual - Page 49
    the vehicle serviced, the remote start system must be disabled using the installed menu wheel. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle
  • Viper 5701 | Owner Manual - Page 50
    Before remote starting a manual transmission vehicle, be sure to: s
  • Viper 5701 | Owner Manual - Page 51
    ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE
  • Viper 5701 | Owner Manual - Page 52
    replace (at Directed's election) with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE
  • Viper 5701 | Owner Manual - Page 53
    DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO THE CONDITIONS AS alarm installed o Year, make, model and color of the automobile o Automobile license number o Vehicle identification number o All security options installed on automobile o Installation
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
O W N E R’ S G U I D E
M
O
D
E
L
5701
©
2011 Directed Electronics. All rights reserved.
G5202V 2011-03
The company behind Viper
®
Auto Security Systems
is Directed Electronics.
Since its inception, Directed Electronics has had one
purpose, to provide consumers with the finest vehicle
security and car stereo products and accessories
available. The recipient of nearly 100 patents
and
Innovations Awards in the field of advanced electronic
technology, Directed Electronics is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced
throughout North America and around the world.
Call
(800) 876-0800
for more information about our
products and services.
Vista, CA 92081
www.directed.com
Directed Electronics is an
ISO 9001 registered company.
Directed Electronics is committed to delivering
world class quality products and services that
excite and delight our customers.
NO ONE DARES COME CLOSE