Toshiba 6420A Specifications
Toshiba 6420A - CCTV Camera Manual
 |
UPC - 032017991118
View all Toshiba 6420A manuals
Add to My Manuals
Save this manual to your list of manuals |
Toshiba 6420A manual content summary:
- Toshiba 6420A | Specifications - Page 1
instructions, and should use a mounting accessory secure part of the ceiling or wall. If installed on a unsecured location the camera connected cables in instructions in the instruction manual. Adjust only those controls that are covered by the instruction manual QUALIFIED SERVICE PERSON AND IK-6420A - Toshiba 6420A | Specifications - Page 2
1 (a) Lens Connector (E.Y.C-221) ........ 1 (b) Instruction Manual 1 (c) Lens Cap 1 1-2 116 (4.57) Bottom View Dimensions : mm (inch) 63 (2.48) Lens: Mount a CS-mount lens. Front View 50 (1.97) Auto-IRIS Terminal Focus ring: Rotate the ring to appropriate setting. - 4 - - 5 - IK-6420A - Toshiba 6420A | Specifications - Page 3
IK-6420A 1-3 4. CAMERA INSTALLATION Installation Example Wall 9.5 (0.37) 4 (0.16) φ6 (0.24) 80 (3. their operation manuals. • Lens, power supply with cable, connectors and coaxial cable are not supplied with the camera. 5-1. Basic connection Single system configuration MONITOR TV CAMERA 24V AC - Toshiba 6420A | Specifications - Page 4
for correct wiring and set up. Video IRIS Lens 1 +12V IRIS terminal 2 NC pin 3 VIDEO 4 GND IRIS Switch VIDEO position Direct Drive IRIS Lens Damp - (y) Damp + (γ) Driver + (wh) Driver - (g) DC position Focus ring IRIS Auto-iris lens 2 1 4 Camera Side 3 1-4 - 8 - - 9 - IK-6420A - Toshiba 6420A | Specifications - Page 5
IK-6420A 1-5 7. LINE-LOCK PHASE If two or more cameras within a system have different AC line phases are switched by the video switcher, the picture on the monitor TV will fluctuate vertically. Connect 24V AC input lines of all cameras used with an auto iris lens, the exposure adjustment is automatically - Toshiba 6420A | Specifications - Page 6
trouble may get much worse and an unpredictable problem may occur. 11. IN CASE OF PROBLEMS Condition No image Unnatural color Check Point Are the camera and connected equipment turned on? Is the iris of the lens adjusted properly? Are cables Internal manually switchable 12 - - 13 - IK-6420A - Toshiba 6420A | Specifications - Page 7
/ 12V DC ±10% Power consumption 3.5W with Al lens (IK-6410A), 4.0W with AI lens (IK-6420A) Image sensor 1/3 inch CCD image sensor Image pickup area Line-Lock, Internal manually switchable Resolution 480 Horizontal TV lines (IK-6410A), 540 Horizontal TV lines (IK-6420A) Minimum illuminance of
-
1 -
2 -
3 -
4 -
5 -
6 -
7
 |
 |
IK-6420A
1-1
- 3 -
•
The CAUTION label, shown on the left,
is attached on the camera.
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightening flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions
in
the
literature
accompanying the appliance.
WARNING :
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION :
CONNECT 24V AC UL LISTED CLASS 2
POWER SUPPLY.
FIELD INSTALLATION MARKING :
THIS INSTALLATION SHOULD BE
MADE BY A QUALIFIED SERVICE
PERSON AND SHOULD CONFORM TO
ALL LOCAL CODES.
FCC (USA)-INFORMATION
NOTE :
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
USER-INSTALLER CAUTION :
Your authority to operate this FCC verified equipment could
be voided if you make changes or modifications not expressly approved by the party.
- 2 -
1.
Read Instructions
All the safety and operating instructions should be
read before the product is operated.
2.
Retain Instructions
The safety instructions and instruction manual should
be retained for future reference.
3.
Warnings
Comply with all warnings on the product and in the
instruction manual.
4.
Follow Instructions
Follow all operating and use instructions.
5.
Cleaning
Disconnect this video product from the power supply
before cleaning.
6.
Attachments
Do not use attachments not recommended by the
video product manufacturer as they may cause
hazards.
7.
Water and Moisture
Do not use this video product near water. Some
examples are: near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool.
8.
Accessories
Do not place this video product on an unstable cart,
stand, tripod, bracket or table. The video product may
fall, causing serious injury to a person, or serious
damage to the product. Use only with stand, tripod,
bracket, or table recommended by the manufacturer,
or sold with the video product. Any mounting of the
product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended
by the manufacturer.
9.
Ventilation
This video product should never be placed near or
over a radiator or heat register. If this product is placed
in a built in installation verify that there is proper
ventilation so that the camera temperature operates
within the recommended temperature range.
10.
Power Sources
This video product should be operated only from the
type of power source indicated on the information
label. If you are not sure of the type of power supply
at your location, consult your product dealer.
11.
Power-Cord Protection
Power cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them. Pay particular attention to cords at
plugs, screws and the point where they exit the
product.
12. Installation
Install this video product on a secure part of the ceiling
or wall. If installed on a unsecured location the camera
could fall causing injury and damage.
13. Lightning
For additional protection on this video product during
a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet and disconnect the power supply and cable
system. This will prevent damage to the video product
due to lightning and power-line surges. If lightning
occurs, do not touch the unit or any connected cables
in order to avoid electric shock.
14. Overloading
Do not overload the power supply or extension cords
as this can result in a risk of fire or electric shock.
15.
Object and Liquid Entry
Never push objects of any kind into this video product
through openings as they may touch dangerous
electrical points or short-out parts that could result in
a fire or electrical shock. Never spill liquid of any kind
on the video product.
16. Servicing
Do not attempt to service this video product yourself
as opening or removing covers may expose you to
dangerous electrical or other hazards. Refer all
servicing to qualified service personnel.
17.
Damage Requiring service
Disconnect this video product from the power supply
and refer servicing to qualified service personnel
under the following conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the video product.
c. If the video product has been exposed to rain or
water.
d. If the video product does not operate normally by
following the operating instructions in the instruction
manual. Adjust only those controls that are covered
by the instruction manual as an improper adjustment
of other controls may result in damage and will often
require extensive work by a qualified technician to
restore the video product to its normal operation.
e. If the video product has been dropped or the cabinet
has been damaged.
f. When the video product exhibits a distinct change
in performance which indicates a need for service.
18.
Replacement Parts
When replacing parts be sure the service technician
uses parts specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
19.
Safety Check
Upon completion of any service or repairs to this video
product, ask the service technician to perform safety
checks to determine that the video product is in proper
operating condition.
IMPORTANT SAFEGUARDS
SECTION 1
GENERAL DESCRIPTION