TP-Link TL-SC3171 User Guide
TP-Link TL-SC3171 Manual
 |
UPC - 845973054021
View all TP-Link TL-SC3171 manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link TL-SC3171 manual content summary:
- TP-Link TL-SC3171 | User Guide - Page 1
TL-SC3171 Day/Night Surveillance Camera Rev: 1.0.1 1910010430 - TP-Link TL-SC3171 | User Guide - Page 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced - TP-Link TL-SC3171 | User Guide - Page 3
This equipment has been tested and found to if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more - TP-Link TL-SC3171 | User Guide - Page 4
WAP Viewing 12 4.1.3 2.5G Mobile Phone Browser Viewing 12 4.2 Using IP Camera via iPhone 13 Chapter 5 Configuration of Main Menu 14 5.1 Live View Default...18 Chapter 6 Setting-BASIC...19 6.1 System ...19 6.1.1 Information ...19 6.1.2 Date/Time...20 6.1.3 Initialize ...21 6.2 Camera - TP-Link TL-SC3171 | User Guide - Page 5
(Point-to-Point Protocol over Ethernet 30 6.3.3 DDNS (Dynamic DNS 32 6.3.4 UPnP (Universal Plug and Play 36 6.3.5 Bonjour...37 6.3.6 IP Notification ...37 6.3.7 Messenger ...39 6.4 Security ...44 6.4.1 Account ...45 6.4.2 HTTPS ...46 Chapter 7 Setting-Advance...48 7.1 FTP client ...48 - TP-Link TL-SC3171 | User Guide - Page 6
be found in your package: ¾ TL-SC3171 Day/Night Surveillance Camera ¾ Power Adapter ¾ Mounting Bracket with three screws, a Lock Ring, a Brace and a Base Plate ¾ RJ45 Cable ¾ Quick Installation Guide ¾ Resource CD, including: z This User Guide z Application Guide z Other helpful information ) Note - TP-Link TL-SC3171 | User Guide - Page 7
to use this IP-Camera normally. If your computer doesn't meet these requirements below, it might cause some problems. Item CPU Graphic codec while installing Intelligent IP Installer. (For Windows 98, ME or 2000 server, the codec might not work properly. You'll need to download Xvid codec 1.0 from - TP-Link TL-SC3171 | User Guide - Page 8
audio. Audio Out: To support audio out with earphones or speakers for two way audio. Power Connector: For connection of 12V DC input. Power LED Indicator: Power LED will light up after completing the boot process. Reset: To successfully restore the camera to factory defaults, please keep the device - TP-Link TL-SC3171 | User Guide - Page 9
I/O Terminal Connector: Input/Output to support External Alarm and Sensor used for motion detection, event triggering and alarm notification, etc. Network Connector: For connection to the Ethernet via RJ45 standard. 4 - TP-Link TL-SC3171 | User Guide - Page 10
Chapter 3 Using IP Camera via Web Browser 3.1 Obain the IP Address 1. Insert the provided CD into your CD-ROM driver. The Setup Wizard will automatically pop up on your computer's screen as shown in the figure below. Figure 3-1 2. Choose the Intelligent IP Installer, and then the next screen appears - TP-Link TL-SC3171 | User Guide - Page 11
is finished, click Start > Program Files > TP-LINK >Intelligent IP Installer to start using the program. Figure 3-3 4. The following screen will then display. Click the Search button to search Network Cameras in the network; it displays Network Cameras information including IP Address. 6 - TP-Link TL-SC3171 | User Guide - Page 12
the Quick Installation Guide. 2) If you only want to view the video without setting page, enter "http:///index2.htm" as your web URL . For example, you can enter "http://192.168.1.100/index2.htm" as your web URL to view the video without setting page. 2. Enter the default User name "admin" and - TP-Link TL-SC3171 | User Guide - Page 13
Figure 3-5 ) Note: The default User name "admin" and Password "admin" are set at the factory for the the Safari icon on the screen as the figure below shown, and enter the IP address of the IP camera (which can be obtained from Figure 3-4) in the Location / Address field of your browser. 8 - TP-Link TL-SC3171 | User Guide - Page 14
) Note: If you only want to view the video without setting page, enter "http:///index2.htm" as your web URL. For example, you can enter "http://192.168.1.100/index2.htm" as your web URL to view the video without setting page. Figure 3-7 9 - TP-Link TL-SC3171 | User Guide - Page 15
2. Enter the default User name "admin" and password "admin" in the dialog box as shown below. Figure 3-8 ) Note: The default Name "admin" and Password "admin" are set at the factory for the administrator. You can change them in the Account Menu (Please check "SETTING → BASIC → - TP-Link TL-SC3171 | User Guide - Page 16
3. The web-based management page will be display on your screen. In the leftmost column of the web-based management page are Setting, Client Setting, and Image Setup. For more details, you can refer to Section 5.2、Section 5.3 and Section 5.4. Figure 3-9 11 - TP-Link TL-SC3171 | User Guide - Page 17
4.1.1 3G Mobile Phone Streaming Viewing For 3G mobile phone viewing, type "rtsp://:/video.3gp " into your 3G Streaming Link. is the Public IP address of your IP camera; is the RTSP port of your IP camera (Default value is 554.) Example: rtsp://100.10.10.1:554/video.3gp ) Note - TP-Link TL-SC3171 | User Guide - Page 18
4.2 Using IP Camera via iPhone You can use TP-LINK Web User Interface via iPhone. Please follow the setting process below. Then you can use TP-LINK Web UI via iPhone. 1. Select Safari function 2. Enter IP address in your web link. 3. Enter name and password. Default values are both admin. Then - TP-Link TL-SC3171 | User Guide - Page 19
Manual are all orange. Please note that they're from our latest firmware, which can be downloaded from our website. Web pages in our previous firmware Live View 5.1.1 Snapshot You can capture a still image shot by the camera and save it in your computer. Symbols Meaning Save Image Close click to - TP-Link TL-SC3171 | User Guide - Page 20
turned off Microphone turned on Microphone turned off ) Note mean the speakers of your computer are turned on to transmit the sounds from the connected IP camera(s) mean you can broadcast to the connected IP camera(s) via the Ethernet using your microphone 15 - TP-Link TL-SC3171 | User Guide - Page 21
Advance settings menus. There are four sub-menus under the BASIC menu, which includes System, Camera, Network, and Security. For more information, you can refer to Section 6.1 System, Section 6.2 Camera, Section 6.3 Network and Section 6.4 Security. There are nine sub-menus under the Advance menu - TP-Link TL-SC3171 | User Guide - Page 22
Click this button to configure the settings of IP Camera, which includes Mode, View Size, Protocol, and Video Buffer. is suggested that you go to Client Setting to select a suitable View Size before using the IP camera as shown in the figure below. For the PC whose resolution is less than 1280*1024, - TP-Link TL-SC3171 | User Guide - Page 23
three main attributes of perceived color, which is affected by different wavelength of color. With higher value of hue, color will be much more vivid. 5.4.5 Default After the adjustment of all settings, you can still click - TP-Link TL-SC3171 | User Guide - Page 24
the submenus including System, Camera, Network, and Security. 6.1 System Click System to display the submenus including Information, Date/Time, and Initialize. 6.1.1 Information The Information page provides the basic information of the product which includes Product Name, Firmware Version and Web - TP-Link TL-SC3171 | User Guide - Page 25
z Synchronize with PC: Select this mode to keep the date and time of this IP Camera the same with the monitoring PC. z Manual setting: Select this mode to adjust manually the date and time of this IP Camera. z Synchronize with NTP: Specify the NTP server name and the Refresh Interval to synchronize - TP-Link TL-SC3171 | User Guide - Page 26
to specified location. ¾ Restore setting: Download the saved setting data of this IP Camera. Click Browse... and select the saved file. Click OK and this IP Camera is adjusted according to the loaded data and then restarted. ¾ Firmware upgrade: Upgrade the device software. Click Browse... and select - TP-Link TL-SC3171 | User Guide - Page 27
applied immediately. The default language is "English". 6.2 Camera Click Camera to display the submenus including General, MPEG4 and MJPEG. 6.2.1 General ¾ RTSP: Switch is On or Off z RTSP Port: Specify the transmission port number of RTSP streaming. The default value is 554. z Port Range: Specify - TP-Link TL-SC3171 | User Guide - Page 28
video server. RTSP is supports by most of the media IR (Infrared) light. One typical abnormal situation is that a barrier is very close to the camera and shields all available light. ¾ Overlay: z Text Overlay: You can see some information on the display screen which includes Date/Time and user - TP-Link TL-SC3171 | User Guide - Page 29
Authentication: If the viewer authentication is On, the users will be requested to type in username and -Transistor Logic) that multicast can pass through. ¾ Image Size: Specify the image size when the network camera transmits. You can choose among 640 x 480, 320 x 240, and 160 x 120. ¾ Frame rate - TP-Link TL-SC3171 | User Guide - Page 30
On (see Setting →Basic → Camera → General), the screen will display as shown below. ¾ Viewer Authentication: If the viewer authentication is On, the users will be requested to type in 10000 and 11000 by default. z Time-To-Live: Set the maximum TTL(Transistor-Transistor Logic) that multicast can pass - TP-Link TL-SC3171 | User Guide - Page 31
of MPEG4 image transmission for a line. You can select the values from 16, 32, 48, 64, 128, 256bps. If RTSP is Off (see Setting →Basic → Camera → General), the screen will display as shown below. 6.2.3 MJPEG If RTSP is On (see Setting →Basic - TP-Link TL-SC3171 | User Guide - Page 32
the screen will display as shown below. ¾ Image Size: Specify the image size when the network camera transmits. You can choose among 640 x 480, 320 x 240, and 160 x 120. ¾ Frame Click Network to display the submenus including Information, PPPoE, DDNS, UPnP, Bonjour, IP Notification and Messenger. 27 - TP-Link TL-SC3171 | User Guide - Page 33
6.3.1 Information The page of Information displays the MAC address of the device. ¾ Obtain an IP address automatically (DHCP): (If a DHCP server is installed on the network) Select this, the IP will be assigned by the DHCP serve. ¾ Obtain DNS server address automatically: Select this to obtain the - TP-Link TL-SC3171 | User Guide - Page 34
Default gateway: Enter the default gateway. ¾ Use the following DNS server address: Select this when you set the fixed IP address as the IP address of DNS server. z Primary DNS server: Enter the IP HTTP port number is set to 2000 and the IP address of your camera is set to 192.168.1.100, you should - TP-Link TL-SC3171 | User Guide - Page 35
use the PPPoE function, you need to turn on the DDNS or IP Notification function at the same time. ¾ IP address: The IP address obtained when the IP camera connecting with network at PPPoE. ¾ User ID: Enter the user ID for authentication necessary for PPPoE connections. Type it up to 64 characters - TP-Link TL-SC3171 | User Guide - Page 36
you can get the IP address of the camera by IP Notification function. For more details, please refer to Section 6.3.6 IP Notification. 4) If the IP Notification function is not configured to report the IP address of the camera, you can reset the camera to its factory default settings by pressing the - TP-Link TL-SC3171 | User Guide - Page 37
providers such as www.dyndns.org, or www.noip.com. The Dynamic DNS client service provider will give you a password or key. ¾ Server name: Choose the DDNS Server from the list. ¾ User ID: Enter the user ID for authentication necessary for DDNS connections. Type it up to 64 characters. ¾ Password - TP-Link TL-SC3171 | User Guide - Page 38
) Note: How to apply DDNS username and Host name? You can apply DDNS username and Host name by the following steps: 1. Log in http://www.dyndns.org, click the Create Account. 2. Input all information and follow step by step with DynDNS. 33 - TP-Link TL-SC3171 | User Guide - Page 39
. 3. Log in with new account and click Account → My Hosts → Add Host Services. 4. Type domain in the Hostname field and select sub-domain. 34 - TP-Link TL-SC3171 | User Guide - Page 40
5. After typing in information, check your DDNS service. 6. Type your DDNS User ID, Password and Host name in Setting → Basic → Network → DDNS. After completing setting, reboot IP Camera. 35 - TP-Link TL-SC3171 | User Guide - Page 41
service application on the LAN. ¾ HTTP port: Enter the HTTP port number and the default HTTP port is 80. ¾ SSL port: Enter the SSL port number and the default at home and corporate environments. The device supports UPnP which is enabled by default. The device will be automatically detected and - TP-Link TL-SC3171 | User Guide - Page 42
in your Windows Browser UI? Please check the link below: http://www.apple.com/support/downloads/bonjourforwindows.html 6.3.6 IP Notification Once IP Notification is set to "On", the camera will automatically send an e-mail notification to tell users its updated network parameters if the network - TP-Link TL-SC3171 | User Guide - Page 43
the updated network information of the camera. ¾ SMTP Server Name: Type the SMTP server name up to 64 characters, or the IP address of the SMTP server. ¾ SMTP Server Port: You can set port number from 1~65535 according to your mail server. The default value is - TP-Link TL-SC3171 | User Guide - Page 44
POP user account. User name, Password: Type the username and password of the user who Default value provides network information including IP, Port, MAC, Model, Firmware Version and Web Version. 6.3.7 Messenger (Supports up to Windows Live Messenger version 8089) If the firmware of your IP Camera - TP-Link TL-SC3171 | User Guide - Page 45
. ¾ Alias: Give an alias for the account of your IP Camera. The figure above takes "TL-SC3171G" for example. ¾ Port range: Enter the port range used. ¾ IP Notification: When this feature is enabled, the IP camera would notify "friends" on MSN about its IP address when it logs into the MSN account or - TP-Link TL-SC3171 | User Guide - Page 46
a Modem Router to access the Internet, you should set your IP Camera as the virtual server with port range 20000-21000 on the Modem Enable Messenger and then set the Login Account, Password, Alias, Port range, IP Notification, Privacy and Allow list parameters as the above figure shows. Click OK to - TP-Link TL-SC3171 | User Guide - Page 47
when you install IntelligentIPInstallerSetup(TPLink)-1.1.16.09.exe. ▲ You can download the IntelligentIPInstallerSetup(TPLink)-1.1.16.09.exe here: http://www.tp-link.com/download/ipcamera/Intelligent_IP_Installer.rar 3. Log into your MSN account. 4. Add the camera's MSN account as a contact - TP-Link TL-SC3171 | User Guide - Page 48
5. Check its status. Normally it should be online. 6. Click the camera icon and select View a contact's webcam to view the video. 43 - TP-Link TL-SC3171 | User Guide - Page 49
7. Wait for a moment, and you will see the video captured by your IP Camera. 6.4 Security Click Security to display the submenus including Account and HTTPS. 44 - TP-Link TL-SC3171 | User Guide - Page 50
The device default account and password setting is "admin / admin". That means everyone who knows IP address can access the device including all configuration. Therefore, it is necessary to assign a password if the device is intended to be accessed by others. ¾ User name: Set a user name between - TP-Link TL-SC3171 | User Guide - Page 51
camera. Click Off and select one (among Admin, Operator and Viewer) from the pull-down list as default, then all users can view directly the video with the default different default TCP port (443) and an additional encryption / authentication layer between the HTTP and TCP, you can use the IP camera - TP-Link TL-SC3171 | User Guide - Page 52
) Note: 1) When enable HTTPS with RTSP on mode, the IP Camera only protect the setting such as username and password and do not protect video and audio. 2) When enable HTTPS with RTSP off mode, the IP Camera will protect all setting including video and audio. 47 - TP-Link TL-SC3171 | User Guide - Page 53
sending images to an FTP server. By using FTP client function, you can send the image and video file which has been shot and recorded linked with the built-in motion detection function to FTP server. FTP client setting menu is composed of three items, General, Alarm sending and Periodical sending - TP-Link TL-SC3171 | User Guide - Page 54
name to upload still images up to 64 characters, or the IP address of the FTP server. ¾ User name: Type the user name for the FTP server. ¾ Password: Type the password for image and video file to the specified FTP server linked with the alarm detection by the built-in motion detection function. Select On - TP-Link TL-SC3171 | User Guide - Page 55
¾ Remote path: Type the path to the destination in FTP server up to 64 characters. ¾ Image file name: Type the file name you want to assign to the images when sending to the FTP server. You can use up to 10 alphanumeric characters, - (hyphen) and _ (underscore) for naming. ¾ Suffix: Select a suffix - TP-Link TL-SC3171 | User Guide - Page 56
) Note: 1) You can set motion detection on motion detection page (Please go to "Setting → Advance →Motion detection → Setting"). For more details, you can check Section 7.7. 2) Motion Detection works only when the MPEG4 function is On and the Cropping is set to Off. z Use Alarm Buffer: Select Use - TP-Link TL-SC3171 | User Guide - Page 57
) Note: You can set the alarm buffer function at Alarm Buffer page (Please go "Setting→ Advance → Alarm Buffer → Setting"). For more details, you can check Section 7.7. z Alarm Input: Select the connected alarm. Sensor input1: The external sensor which is connected to sensor input1 of the alarm - TP-Link TL-SC3171 | User Guide - Page 58
7.5. 7.1.3 Periodical sending You can set to send an image file to FTP server periodically by selecting On to send the image file to FTP server linked with setting period. ¾ Remote Path: Type the path to storage location of FTP server which you have authorized. ¾ Image file name: Type the file name - TP-Link TL-SC3171 | User Guide - Page 59
want to send an image via e-mail. By using Mail (SMTP) function, you can send a mail with attached image and video which has been shot linked with the built-in motion detection function. The image file can also be sent periodically. E-Mail (SMTP) setting menu is composed of three items, General - TP-Link TL-SC3171 | User Guide - Page 60
Off if you do not wish to use the e-Mail (SMTP) function. ) Note: The Setting of General will be the same as the setting of IP Notification (Please check "SETTING → BASIC → Network → IP Notification") 55 - TP-Link TL-SC3171 | User Guide - Page 61
¾ SMTP server name: Type the SMTP server name up to 64 characters, or the IP address of the SMTP server. ¾ SMTP Server Port: You can set port number from 1~65535 according to your mail server. The default value is 25. ¾ Security setting: Check SSL box if the mail server you use has security - TP-Link TL-SC3171 | User Guide - Page 62
server name up to 64 characters, or type the IP address of the POP server. This setting is necessary when the SMTP server which e-mails performs authentication using the POP user account. z User name, Password: Type the user name and Password of the user who has the mail account. This - TP-Link TL-SC3171 | User Guide - Page 63
detection by the external sensor input or by the built-in motion detection function. Select On to send the image and file to SMTP server linked with the alarm detection. ¾ Alarm sending: Select On to set to send mail with connection to the alarm detection. ¾ File attachment: Set whether an image - TP-Link TL-SC3171 | User Guide - Page 64
¾ Alarm z Motion Detection: Click it for using Motion Detection function as a sensor. You can set motion detection function on the motion detection page. 59 - TP-Link TL-SC3171 | User Guide - Page 65
) Note: 1) You can set motion detection on motion detection page (Please go to "Setting → Advance →Motion detection → Setting"). For more details, you can check Section 7.8. 2) Motion Detection works only when the MPEG4 function is On and the Cropping is set to Off. z Use Alarm Buffer: Select Use - TP-Link TL-SC3171 | User Guide - Page 66
) Note: You can set the alarm buffer function at Alarm Buffer page (Please go "Setting→ Advance → Alarm Buffer → Setting"). For more details, you can check Section 7.7. z Alarm input: Select the connected alarm. Sensor input1: The external sensor which is connected to sensor input1 of the alarm - TP-Link TL-SC3171 | User Guide - Page 67
7.5. 7.2.3 Periodical sending You can set to send an image file by SMTP server periodically by selecting On to send the image file by SMTP server linked with setting period. ¾ Image file name: Type the file name of the image sent by SMTP up to 10 alphanumeric characters, (hyphen) and _ (under score - TP-Link TL-SC3171 | User Guide - Page 68
images to an HTTP server. By using HTTP client function, you can send the image file and audio file which has been shot and recorded linked with the built-in motion detection function to HTTP server. HTTP client setting menu is composed of two items, General and Alarm sending. 63 - TP-Link TL-SC3171 | User Guide - Page 69
7.3.1 General ¾ HTTP event: Set up the HTTP server URL, port, User ID, Password, and Proxy Server settings. 64 - TP-Link TL-SC3171 | User Guide - Page 70
same as CGI. 2. The example above is for reference only. For more details, please refer to SDK in the subdirectory of the IP camera product on our website http://www.tp-link.com. 7.3.2 Alarm sending Set to send the mail with connection to the alarm detection by the built-in motion detection function - TP-Link TL-SC3171 | User Guide - Page 71
from your target device. For example, move=down. 9 Message: message will show up in the form of Message = PTZ down. If your target device didn't support the parameter of message, you can't see the message. So you can just take the message as a note. For example: PTZ down. ) Note: 1) You can - TP-Link TL-SC3171 | User Guide - Page 72
9 Message: message will show up in the form of Message = PTZ down. If your target device didn't support the parameter of message, you can't see the message. So you can just take the message as a note. For example: PTZ down. ) Note: You can - TP-Link TL-SC3171 | User Guide - Page 73
can set in this menu to control the alarm out of I / O port on the rear of the device linked to the alarm detection and the timer. 7.4.1 Setting Alarm output: To activate the Alarm output function, select On. When you do not use the Alarm - TP-Link TL-SC3171 | User Guide - Page 74
z Motion Detection: Click it on for using Motion Detection function as a sensor. You can set motion detection function at the motion detection function page. ) Note: 1) You can set motion detection on motion detection page (Please go to "Setting → Advance →Motion detection → Setting"). For more - TP-Link TL-SC3171 | User Guide - Page 75
) Note: You can set the alarm buffer function at Alarm Buffer page (Please go "Setting→ Advance → Alarm Buffer → Setting"). For more details, you can check Section 7.7. z Alarm Input: Select the connected alarm. Sensor input1: The external sensor which is connected to sensor input1 of the alarm - TP-Link TL-SC3171 | User Guide - Page 76
z Schedule: You can specify the period when the periodical sending is effective in the Schedule setting in the other section. ) Note: You can set schedule function at schedule page. (Please go "Setting → Advance → Schedule → Setting") For more details, you can check Section 7.5. 7.5 Schedule When - TP-Link TL-SC3171 | User Guide - Page 77
right of the checked day is the effective days than Mon (Monday) cannot be input. 7.6 Alarm input When you click Alarm Input on the Advance mode menu, the Alarm input setting menu appears. You can set in this menu to control the external alarm input of I / O port on the rear of the device linked - TP-Link TL-SC3171 | User Guide - Page 78
for using external sensor which is connected to sensor input1 of the camera I / O port. z Trigger condition: Select High signal output and Low signal output as your alarm. z Camera move: Pull down the window to select the camera preset position. 7.7 Alarm buffer You can set the Pre-alarm image and - TP-Link TL-SC3171 | User Guide - Page 79
alarm detection. ) Note: The value of Recording capacity differs depending on Image size, Bitrate (for MPEG4) and Image quality (for MPEG4 and MJPEG) in the camera setting menu. 7.8 Motion detection 74 - TP-Link TL-SC3171 | User Guide - Page 80
There are three Motion Detection functions as sensors to set for different detecting zones. Each one has Threshold and Sensitivity inputs which you can adjust to specific zone sequentially. Motion Detection function can support FTP, SMTP and HTTP event for capturing and sending images. 75 - TP-Link TL-SC3171 | User Guide - Page 81
the image different. The higher sensitivity it is and the more frequently it scans. The default value is 50 and the value range is 0~100. The larger the value, the The System Log function allows users to review any changes and events happened. The system begins logging automatically after started. - TP-Link TL-SC3171 | User Guide - Page 82
be shown in system log. In this case, please send the file "backup" to TP-LINK ( you can save it from Setting > Basic > System > Initialize > Backup setting data), and also provide the router spec you're using, we will analyze and solve the problem as soon as possible. E-mail: [email protected] 77 - TP-Link TL-SC3171 | User Guide - Page 83
chapter provides tables that help you to optimize your IP camera with your network environment. Base on your network upload environment to choose the best Image-Quality setting. For example, if the network environment is ADSL 256Kb(upload) / 2Mb(download), the most fluent Image-Quality needs to set - TP-Link TL-SC3171 | User Guide - Page 84
320*240 512 30 550 30 320*240 512 15 600 16 160*120 1024 30 950 30 160*120 1024 15 750 16 160*120 512 30 500 30 160*120 512 15 50 16 160*120 128 30 130 30 160*120 128 15 140 16 A.3 MJPEG @ 15fps / kbps Quality Excellent Detailed Good Standard Medium 640*480 - TP-Link TL-SC3171 | User Guide - Page 85
table to find out the capability for recording into your hard disk. B.1 MPEG4 Storage Requirement GB / channel / day @ 30fps Quality 640*480 320*240 160*120 Excellent 10.5 3.2 0.9 Detailed 4.2 1.6 0.5 Good 3.2 1.1 0.3 Standard 2.6 0.7 0.3 Medium 2.6 0.6 0.2 B.2 MPEG4 Storage - TP-Link TL-SC3171 | User Guide - Page 86
B.3 MPEG4 Storage Requirement GB / channel / day Image-Size Bitrate Setting Frame-Rate Setting 640*480 2048 30 640*480 2048 15 640*480 1536 30 640*480 1536 15 640*480 - TP-Link TL-SC3171 | User Guide - Page 87
/manual/jsp Q3. If the image is blurry, what can I do? Please adjust the IP Camera's focus by rotating the Lens. Q4. If I forgot the IP address and port of my IP Camera. What should I do? Please download the Intelligent IP Installer Setup from our web site, or run the CD firstly. This software
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
 |
 |
TL-SC3171
Day/Night Surveillance Camera
Rev: 1.0.1
1910010430