TP-Link Archer C5 Archer C5 V2 User Guide

TP-Link Archer C5 Manual

Get TP-Link Archer C5 PDF manuals and user guides View all TP-Link Archer C5 manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link Archer C5 manual content summary:

  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 1
    Archer C5 AC1200 Wireless Dual Band Gigabit Router REV2.0.0 1910011251
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 2
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 3
    installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 4
    2012 MHz Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 5
    -5725 MHz Reason/remark Planned General authorization required if used outside own premises General authorization required for network and service supply (not for spectrum) Country Bulgaria Restriction Not implemented Reason/remark Planned France Relevant+ provisions for the implementation of
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 6
    Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 7
    power source.  Don't disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.  Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 8
    : Product Description: AC1200 Wireless Dual Band Gigabit Router Model No.: Archer C5 Trademark: TP-LINK We declare under our standards or other normative documents EN 300 328 V1.8.1 EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1 EN 55022: 2010 + AC: 2011 EN 55024: 2010 EN 61000-3-2: 2006 + A1: 2009 +
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 9
    Layout ...4 1.4.1 The Front Panel 4 1.4.2 The Rear Panel 5 Chapter 2. Connecting the router 7 2.1 System Requirements 7 2.2 Installation Environment Requirements 7 2.3 Connecting the router 7 Chapter 3. Quick Setup 10 Chapter 4. Basic 16 4.1 Network Map...16 4.2 Internet...16 4.3 Wireless
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 10
    5.4.5 Wireless Advanced 46 5.4.6 Wireless Statistics 47 5.5 Wireless 5GHz...48 5.5.1 Wireless Settings 48 5.5.2 WPS ...50 5.5.3 Wireless Security 52 5.5.4 Wireless MAC Filtering 55 5.5.5 Wireless Advanced 57 5.5.6 Wireless Statistics 58 5.6 Guest Network ...59 5.7 DHCP...61 5.7.1 DHCP
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 11
    100 5.18 IPv6 Support ...101 5.18.1 IPv6 Status...102 5.18.2 IPv6 Setup ...103 5.19 System Tools...111 5.19.1 Time Settings 111 5.19.2 Diagnostic ...113 5.19.3 Firmware Upgrade 114 5.19.4 Factory Defaults 115 5.19.5 Backup & Restore 116 5.19.6 Reboot...116 5.19.7 Password ...117 5.19.8 System
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 12
    in your package:  Archer C5 AC1200 Wireless Dual Band Gigabit Router  DC Power Adapter for Archer C5 AC1200 Wireless Dual Band Gigabit Router  Ethernet Cable  Quick Installation Guide  Resource CD for Archer C5 AC1200 Wireless Dual Band Gigabit Router, including: • This Guide • Other Helpful
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 13
    Setup Wizard is supported and detailed instructions are provided step by step in this user guide. Before installing the router, please look through this guide to know all the router's functions. 1.2 Conventions The router or Archer C5 mentioned in this guide stands for Archer C5 AC1200 Wireless
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 14
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 1.3 Main Features  Complies with IEEE 802.11ac.  One 10/100/1000M Auto-Negotiation RJ45 Internet port, four 10/100/1000M Auto-Negotiation RJ45 Ethernet ports, supporting Auto MDI/MDIX.  Provides two USB 2.0 ports supporting file sharing and print
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 15
    1.4 Panel Layout 1.4.1 The Front Panel Archer C5 AC1200 Wireless Dual Band Gigabit Router The router's LEDs are located on the front panel (View from left to right). Name (Power) (2.4G Wireless) (5G Wireless) (Ethernet) (Internet) (WPS) (USB 1) Status Flashing On
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 16
    Archer C5 AC1200 Wireless Dual Band Gigabit Router (USB 2) Flashing On Off The router is identifying router to the local PC(s).  WPS/Reset: Pressing this button for less than 5 seconds enables the WPS function. If your client devices, such as wireless adapters, that support Wi-Fi Protected Setup
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 17
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Pressing this button for more than 5 seconds enables the Reset function. With the router powered on, press and hold the WPS/Reset button for approximately 8 seconds. And then release the button and wait the router to reboot to its factory default
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 18
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Chapter 2. Connecting the router 2.1 System Requirements  Broadband Internet Access Service (DSL/Cable/Ethernet)  One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the router is connected directly to the Ethernet)  PCs
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 19
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 2-1 Hardware Installation  Note: Figure 2-2 Wall-mount Installation The diameter of the screw ranges from 3.5 mm to 8 mm, and the distance between two screws is 122 mm. The screw that projects from the wall needs around 4.5 mm base, and
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 20
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 2-3 USB Installation  Note: If you want to use the router to share files or printer, plug the USB storage device(s) to the USB port(s) or connect the printer to the router with a matching cable. - 9 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 21
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Chapter 3. Quick Setup 1. Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If you need instructions as to how to do this, please refer to Appendix B: Configuring the PC. 2. Open a web-browser (such as Microsoft
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 22
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Note: Per FCC regulations, all Wi-Fi products marketed in -Detect. 3) Auto-Detect supports only three popular connection types, PPPoE, Dynamic IP, and Static IP. If your connection type is L2TP or PPTP, you need to manually select the very type and
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 23
    Static IP Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 3-6 WAN Connection Type - Static IP  IP Address - Enter the IP address into this field.  Subnet Mask - Enter the subnet mask into this field. It is usually 255.255.255.0.  Default Gateway - Enter the gateway IP address into
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 24
    L2TP Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 3-8 WAN Connection Type - L2TP  VPN Server IP/ Domain Name - Enter the server IP address/name provided by your ISP.  Username - Enter the username provided by your ISP. This field is case-sensitive.  Password - Enter the Password
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 25
    PPTP Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 3-9 WAN Connection Type - PPTP  VPN Server IP/Domain Name - Enter the server IP address/name provided by your ISP.  Username - Enter the username provided by your ISP. This field is case-sensitive.  Password - Enter the Password
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 26
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Wireless 2.4GHz/5GHz - Displays whether the wireless function is enabled or not.  Network Name (SSID) - Also called the SSID (Service Set Identification). Enter a value of up to 32 characters. The same name must be assigned to all wireless
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 27
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Chapter 4. Basic 4.1 Network Map Network Map provides a router-centered dashboard Figure 4-1 Network Map  Internet - Click to view the ISP settings of your router.  Wireless Clients - Click to view the wireless devices connected to your network.
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 28
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 4-2 Internet 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the router will automatically get IP parameters from your ISP. You can see the page as shown below. Figure 4-3 Dynamic IP  IP Address - Assigned
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 29
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Primary/Secondary DNS - If your ISP gives the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0.  Default Gateway - Enter the gateway IP address in dotted-decimal notation provided by your ISP.  Primary/
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 30
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 4-5 PPPoE  User Name/Password - Enter the User Name and Password provided by your L2TP  VPN Server IP/Domain Name - Enter the IP address or domain name of your VPN server.  User Name/Password - Enter the User Name and Password provided by
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 31
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 5. If your ISP provides PPTP connection, please select PPTP/Russia PPTP option. And you should enter the following parameters (Figure 4-7). Figure 4-7 PPTP/Russia PPTP  VPN Server IP/Domain Name - Enter the IP address or domain name of your VPN
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 32
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 4.3 Wireless Choosing menu "Basic→Wireless", you can configure wireless network will be hidden from the Wi-Fi network.  Password - Create a password for your wireless network. The password must have a minimum of 8 characters in length. Click the
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 33
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 4-9 File Sharing  Device Setting - Click the Scan button to display the information of the USB storage device connected to the router. Click the Safely Remove button to remove the USB storage device safely from the router by default. If
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 34
    Archer C5 AC1200 Wireless Dual Band Gigabit Router ii. Enter ftp://192.168.0.1:21 in the dialog box and click the OK button. 3) FTP (Remote): This method is disabled by default. If you select this check box, remote users can access the USB device through FTP over the Internet. This feature supports
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 35
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Allow Guest Network Access - If this checkbox is selected, guests are allowed to access the sharing file.  Enable Authentication - If this checkbox is selected, then
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 36
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 4-12 Guest Network  Allow Guests To See Each Other SSID) must be assigned to all wireless devices in your guest network.  Password - Create a password for the guest network. The password must have a minimum of 8 characters in length. - 25 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 37
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Chapter 5. Advanced 5.1 Status Choose menu "Advanced→Status", you can see the current status information about the router. Figure 5-1 Status - 26 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 38
    5.2 Network Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-2 the Network menu There are three the WAN on the screen below. 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the router will automatically get IP parameters from your ISP. You can see the page
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 39
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default the router.  Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 40
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default WAN - PPPoE  User Name/Password - Enter the User Name and Password provided by your ISP. These
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 41
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Static IP - You can check this radio button Connecting function can take effect.  Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 42
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-6 PPPoE Advanced Settings  MTU Size - The default MTU size is "1480" bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP.  Service Name/AC Name - The service name and AC (
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 43
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-7 WAN - L2TP/Russia L2TP  VPN Server IP/Domain Name - Enter the IP address or domain name of the VPN server provided by your ISP.  User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 44
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Connect Automatically - Connect automatically after the router is disconnected. To use this option, check the radio button.  Connect Manually - You can configure the router to make it connect or disconnect manually unless a new link is requested.
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 45
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  VPN Server IP/Domain Name - Enter the IP address or domain name of the VPN server provided by your ISP.  User Name/Password - Enter the User Name and Password unless a new link is requested. Caution service is successfully detected by the router
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 46
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Static IP - Connections which use static IP address assignment. The router cannot detect PPTP/L2TP connections with your ISP. If your ISP uses one of these protocols, then you must configure your connection manually the factory default value. Click
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 47
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-10 LAN  MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed.  IP Address - Enter the IP address of your router or reset it in dotted-decimal notation (factory default: 192.168.0.1).  Subnet
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 48
    5.4 Wireless 2.4GHz Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-12 Wireless menu There are six The wireless network name (SSID) that the router uses. You can create a new one with up to 32 characters. The default SSID is set to be TP-LINK_XXXX. This value is case-sensitive. For
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 49
    Archer C5 AC1200 Wireless Dual Band Gigabit Router wireless features of the router be used. The default channel is set to Auto, so the router will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 50
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  SSID (to be bridged) - The SSID of the AP your router is going to connect to as a client. You can also use the Survey function to select the SSID to join.  MAC Address (to be bridged) - The MAC address (BSSID) of the AP your router is going to
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 51
    Archer C5 AC1200 Wireless Dual Band Gigabit Router If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and the router using either Push Button Configuration (PBC) method or PIN method. I. Use the Wi-Fi Protected Setup Button
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 52
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-17 Wireless Security  Disable Security - - It's the WPA/WPA2 authentication type based on pre-shared passphrase. The router is configured by this security type by default.  Version - You can choose the version of the WPA-PSK or WPA2
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 53
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-18 WPA/WPA2 - Personal  Wireless Password - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. The default password is the same with the default PIN code, which is labeled on the router or can be
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 54
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update.  WEP - It is based on the IEEE 802.11 standard. If you check this radio button, you will find a notice in
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 55
    Archer C5 AC1200 Wireless Dual Band Gigabit Router filter wireless users by MAC Address, click Enable. The default setting is Disabled.  MAC Address - The wireless add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 56
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 3. Select Enabled or Disabled for this entry on MAC address 00-0A-EB-00-07-5F are able to access the router, but all the other wireless stations cannot access the router, you can configure the Wireless MAC Address Filtering list by following these
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 57
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 5.4.5 Wireless Advanced Choose menu "Advanced→Wireless 2.4GHz→Wireless Advanced", you can configure the advanced settings of your wireless network. Figure 5-23 Wireless Advanced  Transmit Power - Here you can specify the transmit power of router.
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 58
    Archer C5 AC1200 Wireless Dual Band Gigabit Router broadcast and multicast messages. When the router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 59
    Archer C5 AC1200 Wireless Dual Band Gigabit Router If the numbers of connected wireless stations go beyond one page, Settings (5GHz)  Wireless Network Name - The wireless network name (SSID) that the router uses. You can create a new one with up to 32 characters. The default SSID is set to be - 48 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 60
    Archer C5 AC1200 Wireless Dual Band Gigabit Router TP-LINK_XXXX_5G. This value is case-sensitive. For example, TEST is NOT the same as test.  Region - The geographic region where the router is being used. This field specifies the region where the wireless function of the router can be used. It
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 61
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  SSID (to be bridged) - The SSID of the AP your router is going to connect to as a client. You can also use the search function to select the SSID to join.  MAC Address (to be bridged) - The MAC address (BSSID) of the AP your router is going to
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 62
    Archer C5 AC1200 Wireless Dual Band Gigabit Router If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and router using either Push Button Configuration (PBC) method or PIN method.  Note: To build a successful connection by
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 63
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 5.5.3 Wireless Security Choose menu "Advanced→Wireless 5GHz→Wireless Security", you can configure the security settings of your wireless network. There are five wireless security modes supported by the router: WPA-Personal, WPA2-Personal, WPA-
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 64
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Note: If you check the WPA/WPA2-Personal radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 5-31. Figure 5-31 WPA/WPA2 - Personal  Wireless Password - You can enter ASCII characters between 8 and 63
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 65
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Radius Server IP - Enter the IP address of the Radius server.  Radius Port - Enter the port number of the Radius server.  Radius Password - Enter the password for the Radius server.  Group Key Update Period - Specify the group key update
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 66
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Note: If you do not set the key, the 5-34. Figure 5-34 Wireless MAC Filtering To filter wireless users by MAC Address, click Enable. The default setting is Disabled.  MAC Address - The wireless station's MAC address that you want to filter.
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 67
    Archer C5 AC1200 Wireless Dual Band Gigabit Router To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 68
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 5.5.5 Wireless Advanced Choose menu "Advanced→Wireless→Wireless Advanced", you can configure the advanced settings of your wireless network. Figure 5-36 Wireless Advanced  Transmit Power - Here you can specify the transmit power of router default
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 69
    Archer C5 AC1200 Wireless Dual Band Gigabit Router messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default any of the values on this page. To update this page and to show the current connected wireless
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 70
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Note: This page will be refreshed automatically every 5 seconds. 5.6 Guest Network Choose menu "Advanced→Guest Network", you can configure the Guest Network Wireless Settings on
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 71
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Access And Bandwidth Control  Allow Guests to See Access Time - During this time the wireless stations could accessing the AP.  Note: The range of bandwidth for Guest Network is calculated according to the setting of Bandwidth Control on the page
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 72
    5.7 DHCP Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-39 The DHCP menu There are three must configure the computer manually.  Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address.  End
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 73
    Archer C5 AC1200 Wireless Dual Band Gigabit Router the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.  Default Gateway - (Optional.) It is suggested to input the IP address of the Ethernet port of the router
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 74
    Archer C5 AC1200 Wireless Dual Band Gigabit Router accesses the DHCP server. Reserved IP addresses should be to reserve an IP address.  Reserved IP Address - The IP address reserved for the PC by the router.  Status - The status of this entry, either Enabled or Disabled. To Reserve an IP address:
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 75
    5.8 USB Settings Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-44 The USB Settings menu There are three "Advanced→USB Settings→Device Settings", you can configure the USB device attached to the router and view the information. Figure 5-45 Device Settings Click the Scan button to scan
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 76
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-46 File Sharing  Sharing Account  Use Login USB device connected to the router.  Access Method - Select the check boxes for the access methods that you want. 1) Network Neighborhood: This method is enabled by default. To access the USB
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 77
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 2) FTP: This method is disabled by default. If you select This method is disabled by default. If you select this check box, remote users can access the USB device through FTP over the Internet. This feature supports both downloading and uploading of
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 78
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Allow Guest Network Access - If this checkbox is selected, and you can enable or disable the NAT boost. It is enabled by default. If NAT boost is enabled, the router will have the best throughout. If NAT boost if disabled, the Bandwidth Control
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 79
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 5.10 Forwarding Figure 5-49 NAT Boost Figure can be used for setting up public services on your LAN. A virtual server is defined as a service port, and all requests from Internet to this service port will be redirected to the computer specified
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 80
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Service Port - The numbers of External Service Ports. You can enter a service port or a range of service ports (the format is XXX - YYY; XXX is the Start port and YYY is the End port).  Internal Port - The Internal Service Port number of the PC
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 81
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Note: It is possible that you have a computer or server that has more than one type of available service. If so, select another service, and type the same IP address for you need, enter the Trigger Port and the Incoming Ports manually. - 70 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 82
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 3. Select the protocol used for Trigger Port from used for Trigger Ports, either TCP, UDP, or All (all protocols supported by the router).  Incoming Port - The port or port range used by the remote system when it responds to the outgoing request.
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 83
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Click the Enable All button to make all entries enabled. Click the Disable All button to make all entries disabled. Click the Delete All button to delete all entries Once the router be refused. 3. Incoming Ports ranges cannot overlap each other. 5.10
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 84
    Archer C5 AC1200 Wireless Dual Band Gigabit Router UPnP devices can be automatically discovered by the UPnP service application on the LAN. Figure 5-56 UPnP Setting or Disable button. This feature is enabled by default.  Current UPnP Settings List - This update the Current UPnP Settings List. - 73 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 85
    5.11 Security Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-57 The Security menu There are four submenus under the through the session conforms to the protocol. SPI Firewall is enabled by factory default. If you want all the computers on the LAN exposed to the outside world, you can disable
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 86
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pass through the router. , through the use of cryptographic security services. To allow IPSec tunnels to pass through the router, click Enable.  ALG - It
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 87
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-59 Advanced Security  Packets Statistics Interval (5~60) - The default value is SYN Flood, UDP Flood and ICMP-Flood.  DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 88
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current UPD-FLOOD Packets number is beyond the set value, the router will startup the blocking function immediately.  Enable TCP-SYN-FLOOD
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 89
    Archer C5 AC1200 Wireless Dual Band Gigabit Router tasks", and then enter each MAC Address in a separate field. The format for the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). Only the PCs with MAC address listed can use the password service port 80. This router's default remote
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 90
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 2. Be sure to change the router's default password to a very secure password. 5.12 Parental Control - This field displays the MAC address of the PC that is managing this router. If the MAC Address of your adapter is registered, you can click the
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 91
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-63 Add or Modify Parental Control Entry 2. Enter the MAC address of the PC (e.g. 00-11-22-33-44-AA) you'd like to control
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 92
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 1. Click "Parental Control" menu on the left to enter the Parental Control Settings page. Check Enable and enter the MAC address 00-11-22-33-
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 93
    Archer C5 AC1200 Wireless Dual Band Gigabit Router checkbox to enable the Internet Access Control function, so the Default Filter Policy can take effect.  Rule Name - - Here you can edit or delete an existing rule.  Setup Wizard - Click the Setup Wizard button to create a new rule entry.  Add New
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 94
    Archer C5 AC1200 Wireless Dual Band Gigabit Router One: 1. Click Setup Wizard button and the next screen will appear as shown in Figure 5-66. Figure 5-66 Quick Setup - Create a item:  LAN IP Address - Enter the IP address or address range of the host in dotted-decimal format (e.g. 192.168.0.23). If
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 95
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-67 Quick Setup - Create an Access Target Entry  Target  Target Port - Specify the port or port range for the target. For some common service ports, you can make use of the Common Service Port item below.  Protocol - Here are four
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 96
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-68 Quick Setup deselect the checkbox and specify the Start Time and Stop Time manually.  Start Time - Enter the start time in HHMM format as shown in Figure 5-69. Figure 5-69 Quick Setup - Create an Internet Access Control Entry  Rule
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 97
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Target - In this filed, select a target from the drop choose "Allow the packets specified by any enabled access control policy to pass through the router". 2. Click Setup Wizard button. 3. Add a new host with the Host Description is Host_1 and MAC
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 98
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 4. Add a new target with the Target Description is Target_1 and Domain Name is www.google.com, and click Next. 5. Add a new schedule with the Schedule
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 99
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-72 Add or Modify a Host Entry 2) If you select MAC Address, the screen is shown as Figure 5-73.  In Host Description field, create a unique
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 100
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 5.13.3 Target Choose menu "Advanced→Access the Target Port will be automatically filled. If the Common Service Port drop-down list doesn't have the service you want, specify the Target Port manually. 4) In Protocol field, select TCP, UDP, ICMP
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 101
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-76 Add or Modify an Access Target Entry 1) In Target Description field, create a unique description for the target, e.g. Target_1. 2) In Domain Name field, enter
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 102
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-77 Schedule Settings  Schedule Description - Displays the description of the schedule and this description is unique.  Day - Displays the day(s) in a week.  Time - Displays
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 103
    Archer C5 AC1200 Wireless Dual Band Gigabit Router For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA to access www.google.
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 104
    Archer C5 AC1200 Wireless Dual Band Gigabit Router To add static routing entries: 1. Click Add New... shown and which portion is the host portion.  Default Gateway - This is the IP Address of the gateway device that allows for contact between the router and the network or host. 3. Select Enabled or
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 105
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-82 System Routing Table  Destination Network Gateway - This is the IP address of the gateway device that allows for contact between the router and the network or host.  Interface - This interface tells you either the Destination IP Address
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 106
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-84 Bandwidth Control Settings  Enable Bandwidth Control - about the rules such as address range.  Egress bandwidth - This field displays the max and mix upload bandwidth through the Internet port, the default is 0.  Ingress bandwidth -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 107
    Archer C5 AC1200 Wireless Dual Band Gigabit Router To add/modify a Bandwidth Control rule, follow the steps below. 1. Click Add New... shown in Figure 5-85, you will see a new screen shown in Figure 5-
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 108
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-88 Binding Setting  MAC Address - The MAC address of the controlled computer in the LAN.  IP Address - The assigned IP address of the controlled
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 109
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 1. Click the Find button in Figure 5-88. 2. Enter the MAC Address or IP Address. 3. Click the Find button in Figure 5-90. Figure 5-90 Find IP &
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 110
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Note: An item could not be loaded to set up for DDNS, follow these instructions: 1. Enter the Domain Name your dynamic DNS service provider gave. 2. Enter the User Name for your DDNS account. 3. Enter the Password for your DDNS account. 4. Click
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 111
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service.  Note: If you want to login again with another account after a successful login, please click the Logout button, then input
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 112
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-94 No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the User Name for your DDNS account. 2. Enter the Password for your DDNS account. 3. Enter the Domain Name you received from dynamic DNS service provider. 4.
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 113
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-96 IPv6 Status The IPv6 Status page displays the router's current IPv6 status and configuration. All information is read-only.  WAN • Connection Type - The IPv6 connection way for WAN • IPv6 Address - The WAN IPv6 address • IPv6 Default
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 114
    Setup Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-97 Enable/Disable IPv6  Enable IPv6 - Tick the checkbox to enable the IPv6 function. It's enabled by default Connections which use PPPoEV6 that requires a user name and password. • Tunnel 6to4 - Connections which use 6to4 address
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 115
    1) DHCPv6 Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-98 DHCPv6 - SLAAC Figure 5-99 DHCPv6 - DHCPv6 Server  Get non-temporary IPv6 address - Get a non-temporary IPv6 address from the ISP. - 104 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 116
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Get IPv6 prefix delegation - Get a temporary connecting to the router with the current DHCPv6 Address. Enter the amount of time (in seconds) that the DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value is 86400
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 117
    2) Static IPv6 Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-100 Static IPv6 - SLAAC Figure 5-101 Static IPv6 - DHCPv6 Server  IPv6 Address - Enter the IPv6 address in dotted-decimal notation provided by your ISP.  Default Gateway - Enter the default gateway in dotted-decimal
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 118
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  MTU Size - The normal MTU (Maximum Transmission connecting to the router with the current DHCPv6 Address. Enter the amount of time (in seconds) that the DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value is 86400
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 119
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-103 PPPoEv6 - DHCPv6 Server  User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.  Get IPv6 Address Way • Get non-temporary IPv6 address - Get a non-temporary IPv6 address by DHCPv6
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 120
    4) Tunnel 6to4 Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-104 Tunnel 6to4 - SLAAC Figure 5-105 Tunnel 6to4 - DHCPv6 Server - 109 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 121
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Address/Subnet Mask/Default Gateway - the IPv4 address/ subnet mask/ default router with the current DHCPv6 Address. Enter the amount of time (in seconds) that the DHCPv6 address will be leased. The time range is 1~691200 seconds. The default
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 122
    5.19 System Tools Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-106 The System Tools menu Choose menu "System Tools", and you can see the submenus under the main menu: Time Settings, Diagnostic, Firmware Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, System Log and
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 123
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Time Zone - Select your local time zone from this .  Daylight Saving Status - Displays the status whether the Daylight Saving is in use. To set time manually: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 124
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Note: 1. This setting will be used for some time-based functions such as firewall. You must specify your time zone once you login to the router successfully; otherwise, these functions will not take effect. 2. The time will be lost if the router
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 125
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  IP Address/Domain Name - Enter the IP Address or Domain Name of the PC whose connection you wish to diagnose.  Pings Count - Specifies the number of Echo Request messages sent. The default is 4.  Ping Packet Size - Specifies the number of data
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 126
    The hardware version of the upgrade file must accord with the router's current hardware version. To upgrade the router's firmware, follow these instructions below: 1. Download a most recent firmware upgrade file from our website (www.tp-link.com). 2. Enter or select the path name where you save the
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 127
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  The default Subnet Mask: 255.255.255.0  Note: All changed settings will be lost when defaults are these instructions. • Click the Browse button to find the configuration file which you want to restore. • Click the Restore button to update the
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 128
    Management Port. • Upgrade the firmware of the router (system will reboot automatically). • Restore the router's settings to factory defaults (system will reboot automatically). • Update the configuration with the file (system will reboot automatically. 5.19.7 Password Choose menu "Advanced→System
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 129
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-116 System Log  Auto Mail Feature - Indicates whether auto mail feature is enabled or not.  Mail - Most SMTP Server requires Authentication. It is required by most mailboxes that need User Name and Password to log in. - 118 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 130
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  Note: Only when you select Authentication, do you have to enter the User Name and Password in the following fields. • User Name - Your mail account name filled in the From field. • Password - Your mail account password. • Confirm The Password -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 131
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure 5-118 Statistics  Current Statistics Status - Enable or Disable. The default value is to refresh automatically. Click the Refresh button to refresh immediately. Click Reset All to reset the values of all the entries to zero. Click Delete All
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 132
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Statistics Table: IP/MAC Address The IP and MAC address are displayed with related statistics. Total The total number of packets received and transmitted by the Packets router Max transmitting rate". Modify Reset Delete Reset the value of the
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 133
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the Internet port on the router. The
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 134
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 2. How do I configure the router to access Internet by Ethernet users? 1) Login to the router router and click the "Network" menu link on the left of your browser, and then click "MAC Clone" submenu link "1720" for the "Service Port" blank, and your
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 135
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure A-5 Add or Modify a Virtual server Entry  Note: Your opposite side should call your WAN IP, which is displayed on the "Status" page. 4) How to enable DMZ Host: Log in to the router, click the "Forwarding" menu on the left of your browser,
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 136
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure A-7 Basic Security 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the router your router is 192.168.0.x, the default LAN IP of the router will
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 137
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 3) Log in to the router, click the "Forwarding" menu on the left of your browser, and click the "Virtual Servers" submenu. On the "Virtual Servers" page, click Add New..., then
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 138
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Appendix B: Configuring the PC In this section, we'll use Windows 7 as an example to introduce how to install and configure the TCP/IP correctly. First make sure your Ethernet adapter is working, refer to the adapter's manual if needed. 1. Install
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 139
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 3) Click on Change adapter settings. Figure B-3 4) Right-click Local Area Connection, and then select Properties. Figure B-4 5) In the Local Area Connection Properties window, click on Internet Protocol Version 4 (TCP/IPv4). Figure B-5 - 128 -
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 140
    Archer C5 AC1200 Wireless Dual Band Gigabit Router 6) Select Obtain an IP address automatically and Obtain DNS server address automatically. Figure B-6 2. Verify the network connection between your PC and the router Open a command prompt, and type ping 192.168.0.1, and then press Enter.  If the
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 141
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Figure B-5 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and the router correct?  Note: The Ethernet LED on the router and LEDs on your PC's adapter should be lit. 2. Is the
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 142
    Archer C5 AC1200 Wireless Dual Band Gigabit Router Appendix C: Specifications General Standards Protocols Internet RJ45 port; 4 10/100/1000M Auto-Negotiation Ethernet RJ45 ports supporting Auto MDI/MDIX; 2 USB ports supporting storage/FTP/Media/Print Server; 10BASE-T: UTP category 3, 4, 5 cable
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 143
    Archer C5 AC1200 Wireless Dual Band Gigabit Router throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps for a special-purpose service such as Internet gaming or videoconferencing.  DNS (Domain Name System) - An Internet Service that translates the
  • TP-Link Archer C5 | Archer C5 V2 User Guide - Page 144
    Archer C5 AC1200 Wireless Dual Band Gigabit Router  MTU (Maximum Transmission Unit) - The size in bytes of over an always-on connection by simulating a dial-up connection.  SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Archer C5
AC1200 Wireless Dual Band Gigabit Router
REV2.0.0
1910011251