TP-Link Archer C2 Archer C2 V1 User Guide 1910010993

TP-Link Archer C2 Manual

Get TP-Link Archer C2 PDF manuals and user guides View all TP-Link Archer C2 manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link Archer C2 manual content summary:

  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 1
    Archer C2 AC750 Wireless Dual Band Gigabit Router REV1.0.0 1910010993
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 2
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 3
    installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 4
    2012 MHz Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 5
    Cet appareil est conforme aux norms CNR exemptes de licence d'Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1)cet appareil ne doit pas provoquer d'interférences et (2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 6
    power source.  Don't disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.  Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 7
    equipment: Product Description: AC750 Wireless Dual Band Gigabit Router Model No.: C2 Trademark: TP-LINK We declare under our own conformity with the following standards or other normative documents EN 300 328 V1.7.1: 2006 EN 301 489-1 V1.9.2:2011& EN301 489-17 V2.2.1:2012 EN 55022:2010 EN 55024:
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 8
    2.2 Installation Environment Requirements 7 2.3 Connecting the Router 7 Chapter 3. Quick Installation Guide 9 3.1 TCP/IP Configuration 9 3.2 Quick Installation Guide 11 Chapter 4. Configuring the router 21 4.1 Login ...21 4.2 Status ...21 4.3 Quick Setup...22 4.4 Network ...23 4.4.1 WAN ...23
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 9
    4.7.1 Basic Settings 48 4.7.2 WPS ...50 4.7.3 Wireless Security 53 4.7.4 Wireless MAC Filtering 57 4.7.5 Wireless Advanced 59 4.7.6 Wireless Statistics 60 4.8 Guest Network ...61 4.9 DHCP ...62 4.9.1 DHCP Settings 62 4.9.2 DHCP Clients List 64 4.9.3 Address Reservation 64 4.10 USB Settings
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 10
    Status 107 4.20.2 IPv6 WAN 108 4.20.3 IPv6 LAN ...112 4.21 System Tools ...113 4.21.1 Time Settings 113 4.21.2 Diagnostic 115 4.21.3 Firmware Upgrade 117 4.21.4 Factory Defaults 118 4.21.5 Backup & Restore 118 4.21.6 Reboot ...119 4.21.7 Password...119 4.21.8 System Log 120 4.21.9 Statistics
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 11
    in your package:  Archer C2 AC750 Wireless Dual Band Gigabit Router  DC Power Adapter for Archer C2 AC750 Wireless Dual Band Gigabit Router  Quick Installation Guide  Resource CD for Archer C2 AC750 Wireless Dual Band Gigabit Router, including:  This Guide  Other Helpful Information  Note
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 12
    complete data privacy. Flexible Access Control The Archer C2 AC750 Wireless Dual Band Gigabit Router provides flexible access control, so that parents or network administrators can establish restricted access policies for children or staff. It also supports Virtual Server and DMZ host for Port
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 13
    or Archer C2 mentioned in this guide stands for Archer C2 AC750 Wireless Dual Band Gigabit Router without any explanation. 1.3 Main Features  Complies with IEEE 802.11ac.  One 10/100/1000M Auto-Negotiation RJ45 Internet port, four 10/100/1000M Auto-Negotiation RJ45 Ethernet ports, supporting Auto
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 14
    Archer C2 AC750 Wireless Dual Band Gigabit Router 1.4 Panel Layout 1.4.1 The Front Panel Figure 1-1 LEDs on the front panel The router's LEDs Off The wireless function is disabled. On The wireless function is enabled. The router is working on 2.4GHz or 5GHz or both radio band. (Ethernet) Off
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 15
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 1-2 Rear Panel sketch The following parts are located on the rear panel (View from left to right).  WPS/Reset: Pressing this button for less than 5 seconds enables the WPS function. If your client devices, such as wireless adapters, support
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 16
    : The switch for the power.  Power: The Power socket is where you will connect the power adapter. Please use the power adapter provided with this Archer C2 AC750 Wireless Dual Band Gigabit Router.  Wireless antenna: To receive and transmit the wireless data. - 6 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 17
    Archer C2 AC750 Wireless Dual Band Gigabit Router Chapter 2. Connecting the router 2.1 System Requirements  Broadband Internet Access Service (DSL/Cable/Ethernet)  One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the router is connected directly to the Ethernet)  PCs with
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 18
    Archer C2 AC750 Wireless Dual Band Gigabit Router power on the router, please make sure your computer is NOT connected to any other wireless network.) Figure 2-1 Hardware Installation Figure 2-2 USB Installation  Note: If you want to use the router to share files or printer, plug the USB storage
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 19
    Archer C2 AC750 Wireless Dual Band Gigabit Router Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your AC750 Wireless Dual Band Gigabit Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the router
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 20
    Archer C2 AC750 Wireless Dual Band Gigabit Router  If the result displayed is similar to Figure 3-2, it means the connection between your PC and the router failed. Figure 3-2 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 21
    Archer C2 AC750 Wireless Dual Band Gigabit Router 3.2 Quick Installation Guide With a Web-based utility, it is easy to configure and manage the AC750 Wireless Dual Band Gigabit Router. The Web- finish it. 2. After successful login, the Quick Setup page will appear for you to quickly configure your
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 22
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 3-5 Quick Setup 3. Click Next, and then WAN Connection Type page will appear, shown in Figure 3-6. Figure 3-6 WAN Connection Type The router provides Auto-Detect function and supports Internet service is successfully detected by the router. 
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 23
    Archer C2 AC750 Wireless Dual Band Gigabit Router 1) If the connection type detected is Dynamic IP, case, please select "Yes, I need to clone MAC address" and then click Next. Figure 3-7 Quick Setup - MAC Clone 2) If the connection type detected is Static IP, the next screen will appear as shown
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 24
    Archer C2 AC750 Wireless Dual Band Gigabit Router 3) If the connection type detected is PPPoE/Russia PPPoE, the next screen will appear as shown in Figure 3-9. Configure the following parameters and then click Next to continue. Figure 3-9 Quick Setup - PPPoE/Russia PPPoE  User Name/Password - Enter
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 25
    Archer C2 AC750 Wireless Dual Band Gigabit Router Select Dynamic IP if none of the above in Figure 3-11. Configure the following parameters and then click Next to continue. Figure 3-11 Quick Setup - PPTP/Russia PPTP  Username/Password - Enter the Username and Password provided by your ISP.
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 26
    Archer C2 AC750 Wireless Dual Band Gigabit Router Select Dynamic IP if none of the above Figure 3-12. Here we take "2.4GHz and 5GHz" for example. Click Next to continue. Figure 3-12 Quick Setup - Dual Band Selection  2.4GHz - You can use the 2.4GHz band to connect to many classic wireless devices
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 27
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 3-13 Quick Setup - Wireless 2.4GHz  Wireless Network Name - Also called the SSID (Service Set Identification). Enter a value of up to 32 characters. The same name must be assigned to all wireless devices in your network. The default SSID
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 28
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Band - This field displayed the operating frequency being configured.  Mode - This field determines the wireless mode which the router notice interference problems with Setup - Wireless 5GHz  Wireless Network Name - Also called the SSID (Service
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 29
    Archer C2 AC750 Wireless Dual Band Gigabit Router your network. The default SSID is set to be TP-LINK_5GHz_XXXXXX. This value is case-sensitive. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. If you select "Auto", then the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 30
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 3-15 Quick Setup - Comfirm 9. Click the Finish button to complete the Quick Setup. Figure 3-16 Quick Setup - Finish - 20 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 31
    Archer C2 AC750 Wireless Dual Band Gigabit Router Chapter 4. Configuring the router This chapter will show each key and instructions. The detailed explanations for each Web page's key function are listed below. 4.2 Status The Status page provides the current status information about the router. All
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 32
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-1 Status 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide. - 22 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 33
    4.4 Network Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-2 the Network menu There are three the WAN on the screen below. 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the router will automatically get IP parameters from your ISP. You can see the page
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 34
    Archer C2 AC750 Wireless Dual Band Gigabit Router with Unicast - A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get the IP Address normally, you Set DNS server manually - If your ISP gives you one or two DNS addresses, select Set DNS server manually and enter
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 35
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-4 WAN - Static IP  IP Address - Enter the IP IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the modem router. The default value is enabled, and if you are not sure, please contact your ISP or
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 36
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-5 WAN - PPPoE  Username/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.  Secondary Connection - It's available only
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 37
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports appear: Figure 4-6 PPPoE Advanced Settings  Service Name/Server Name - The service name and server name should not be
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 38
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Detect Online Interval - The router will detect Access Concentrator online at If your ISP does not automatically assign DNS addresses to the router during login, please click "Set DNS server manually" check box and enter the IP address of your ISP
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 39
    Archer C2 AC750 Wireless Dual Band Gigabit Router NSW / ACT - nsw.bigpond.net.au VIC / TAS / WA / SA / NT your Internet access disconnects.  Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 40
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-8 WAN - L2TP/Russia L2TP  UserName/Password - IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the modem router. The default value is enabled, and if you are not sure, please contact your ISP or
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 41
    Archer C2 AC750 Wireless Dual Band Gigabit Router Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the router the Internet connecting last unless a new link is requested. Caution: Sometimes the connection cannot
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 42
    Archer C2 AC750 Wireless Dual Band Gigabit Router Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the router have the Internet connecting last unless a new link is requested. Caution: Sometimes the connection
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 43
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Note: If you don't know how to choose the appropriate connection type, click the Detect button to allow the router service is successfully detected by the router then you must configure your connection manually. 4.4.2 LAN Choose menu "Network →
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 44
    Archer C2 AC750 Wireless Dual Band Gigabit Router 2) If the new LAN IP Address you set is not in  Your PC's MAC Address - This field displays the MAC address of the PC that is managing the router. If the MAC address is required, you can click the Clone MAC Address button and this MAC address will
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 45
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-12 Dual Band Selection  2.4GHz (802.11b/g/n) - Click the box, and then the router will only work in 2.4GHz frequency. You can use the 2.4GHz band to connect to many classic wireless devices like gaming consoles, laptops, DVRs, ect. 
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 46
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-14 Wireless Settings - 2.4GHz  Wireless Network Name - Also called the SSID (Service Set Identification). Enter a value of up to 32 characters. The same name must be assigned to all wireless devices in your network. Considering your
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 47
    Archer C2 AC750 Wireless Dual Band Gigabit Router  11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. It is strongly recommended that you set the Mode to 802.11bgn mixed, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the router. 
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 48
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Key type - This option should be chosen the screen as shown in Figure 4-16. This section will guide you to add a new wireless device to an existing network quickly by WPS (Wi-Fi Protected Setup) function. Figure 4-16 WPS  WPS - Enable or disable
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 49
    Archer C2 AC750 Wireless Dual Band Gigabit Router If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and router using either Push Button Configuration (PBC) method or PIN method.  Note: To build a successful connection by
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 50
    Archer C2 AC750 Wireless Dual Band Gigabit Router router's Wi-Fi Protected Setup screen, shown in Figure 4-16 (It is also labeled on the bottom of the router). Step 2: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup security modes supported by the router: WPA-Personal,
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 51
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-20 Wireless Security  Disable Wireless Security WPA/WPA2-Personal - It's the WPA/WPA2 authentication type based on pre-shared passphrase. The router is configured by this security type by default.  Authentication Type - you can choose the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 52
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Note: If you check the WPA/WPA2-Personal radio button The default password is the same with the default PIN code, which is labeled on the bottom of the router or can be found in Figure 4-16.  Group Key Update Period - Specify the group key update
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 53
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update.  WEP -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 54
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.6.4 Wireless MAC Filtering Choose menu "Wireless 2.4GHz → Wireless MAC Filtering", you can control the wireless access by configuring the Wireless MAC Filtering function, shown in
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 55
    Archer C2 AC750 Wireless Dual Band Gigabit Router To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX:XX:XX:XX:XX:XX (X is any
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 56
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.6.5 Wireless Advanced Choose menu "Wireless 2.4GHz → Wireless Advanced", you can configure the advanced settings of your wireless network. Figure 4-26 Wireless Advanced  Transmit Power - Here you can specify the transmit power of router. You
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 57
    Archer C2 AC750 Wireless Dual Band Gigabit Router  DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the router has
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 58
    Archer C2 AC750 Wireless Dual Band Gigabit Router If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 59
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Wireless Network Name - Also called the SSID (Service Set Identification). Enter a so the router will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 60
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Enable WDS Bridging - Check this box to enable WDS. With this function, the router can bridge two or 4-31. This section will guide you to add a new wireless device to an existing network quickly by WPS (Wi-Fi Protected Setup) function. - 50 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 61
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-31 WPS  WPS - Enable or disable the WPS function here.  Current PIN - The current value of the router's PIN is displayed here. The default PIN of the router can be found in the label or User Guide.  Restore PIN - Restore the PIN of the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 62
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-32 Figure 4-33 Add A New Device Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 4: When the WPS LED is on, the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 63
    Archer C2 AC750 Wireless Dual Band Gigabit Router router's Wi-Fi Protected Setup screen, shown in Figure 4-31 (It is also labeled on the bottom of the router). Step 2: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup security modes supported by the router: WPA-Personal,
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 64
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-35 Wireless Security  Disable Security - WPA/WPA2-Personal - It's the WPA/WPA2 authentication type based on pre-shared passphrase. The router is configured by this security type by default.  Authentication Type- you can choose the version
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 65
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Note: If you check the WPA/WPA2-Personal radio button The default password is the same with the default PIN code, which is labeled on the bottom of the router or can be found in Figure 4-31.  Group Key Update Period - Specify the group key update
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 66
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Radius Server Password - Enter the password for the Radius server.  Group Key Update Period - Specify the group key update interval in seconds. The value should
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 67
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.7.4 Wireless MAC Filtering Choose menu "Wireless → MAC Filtering", you can control the wireless access by configuring Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follow these instructions: - 57 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 68
    Archer C2 AC750 Wireless Dual Band Gigabit Router 1. Enter the appropriate MAC Address into the MAC MAC address 00:0A:EB:00:07:5F are able to access the router, but all the other wireless stations cannot access the router, you can configure the Wireless MAC Address Filtering list by following these
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 69
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.7.5 Wireless Advanced Choose menu "Wireless → Wireless Advanced", you can configure the advanced settings of your wireless network. Figure 4-41 Wireless Advanced  Transmit Power - Here you can specify the transmit power of router. You can
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 70
    Archer C2 AC750 Wireless Dual Band Gigabit Router (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 71
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Note: This page will be refreshed automatically every 5 seconds. 4.8 Guest Network Choose "Guest Network", and you can configure the Guest Network Wireless Settings on the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 72
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Allow Guest To Access My Local Network - If enabled, DHCP Settings", you can configure the DHCP Server on the page as shown in Figure 4-45.The router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 73
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-45 DHCP Settings  DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network , otherwise you must configure the computer manually.  Start IP Address - Specify an IP
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 74
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.9.2 DHCP Clients List Choose menu "DHCP → DHCP Clients List", you can view the information about the clients attached to the router in the screen as shown in Figure 4-46. Figure 4-46 DHCP Clients List  Client Name - The name of the DHCP client
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 75
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-47 Address Reservation  MAC Address - The MAC address of the PC for which you want to reserve an IP address.  IP Address - The IP address reserved for the PC by the router.  Status - The status of this entry, either Enabled or Disabled.
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 76
    4.10 USB Settings Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-49 The USB Settings menu There are six submenus under the USB Settings menu (shown in Figure 4-49): USB Mass Storage, User Accounts, Storage
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 77
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-51 User Account Management Only Administrator can use a Web browser to transfer the files from a PC to the Writable shared volume on the USB
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 78
    Archer C2 AC750 Wireless Dual Band Gigabit Router 1. Please restart the service for the new settings to take effect. 2. If you cannot use the new user name and password to access the shares, press Windows logo + R to
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 79
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Status - Indicates the shared or non-shared status of the volume.  Edit - Click Edit to edit the entry. To add a new folder, follow the instructions below. 1. Click Add New Folder in Figure 4-52. Figure 4-53 Add or Modify Share Folder 2. Enter
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 80
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.10.4 FTP Server Choose menu "USB Settings→FTP - The WAN IP address of this router,  Service Port - Enter the FTP Port number to use. The default is 21. To set up your FTP Server, please follow the instructions below: 1. Plug an external USB hard
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 81
    Archer C2 AC750 Wireless Dual Band Gigabit Router 6. Click the Apply button to start the ftp server. To add a new folder, follow the instructions below. 1. Click Add New Folder in Figure 4-54. Figure 4-55 Add or Modify Share Folder 2. Enter display name of the share folder in Shared Name
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 82
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-56 Media Server Setting  Server Enable - To set up your media server, please follow the instructions below: 1. Plug an external USB hard disk drive or USB flash drive into this router, and then click the Enable button to start the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 83
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-58 Add New Folder  Share Name - You can enter a display name they are as follows:  Online - Indicates the print service has been turned on, and no user is using the print service at present. You can click the "Stop" button to stop the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 84
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Offline - Indicates the print service feature is disabled. You can click "Start" button to start the print service. 4.11 NAT Choose "NAT", and you can enable or disable the NAT and Hardware NAT Control feature. The NAT Rules and Hardware NAT will
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 85
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.12.1 Virtual Servers Choose menu "Forwarding→Virtual Servers", and then you can view and add virtual servers on this page (shown in Figure 4-62). Virtual servers can be used for setting up public services on your LAN. A virtual server is defined as
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 86
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4. Select the protocol used for this application in possible that you have a computer or server that has more than one type of available service. If so, select another service, and type the same IP address for that computer or server. To modify or
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 87
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-64 Port Triggering  Trigger Port - The port for outgoing traffic. An outgoing connection using this port will trigger this rule.  Trigger Protocol - The protocol used for Trigger Ports, either TCP, UDP, or All (all protocols supported by
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 88
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-65 Add or Modify a Triggering Entry To host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing. The router forwards packets of all services to the DMZ host. Any PC whose port is being
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 89
    Archer C2 AC750 Wireless Dual Band Gigabit Router DHCP client function disabled and should have a new the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN. Figure 4-67 UPnP Setting  Current UPnP Status - UPnP can be
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 90
    Archer C2 AC750 Wireless Dual Band Gigabit Router  External Port - The port which the router opened for the application.  Protocol - The type of protocol which is opened.  Internal Port - The port which the router opened for local host.  IP Address - The IP address of the local host which
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 91
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-69 Basic Security  Firewall - A firewall protects your network from the outside world. Here you can enable or disable the router's firewall.  SPI Firewall - SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 92
    Archer C2 AC750 Wireless Dual Band Gigabit Router the use of cryptographic security services. To allow IPSec tunnels to pass through the router, click Enable.  ALG - It is recommended to enable Application Layer Gateway (ALG) because ALG allows customized Network Address Translation (NAT) traversal
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 93
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Note: Dos Protection will take effect only when the Traffic Port. The default setting is disabled. If enabled, the ping packet from LAN cannot access the router. This function can be used to defend against some viruses. Click the Save button to save
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 94
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-71 Local Management By default, the radio button "All the PCs on the LAN are allowed to access the Router's Web-Based Utility" is checked. If you want to allow PCs with specific MAC Addresses to access the Setup page of the router's Web-
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 95
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-72 Remote Management  Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router's default remote management web port number is 80. For greater security, you can change the remote management web
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 96
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-73 Parent Control Settings  Parent Control - Check Enable if you want this function to take effect; otherwise, check Disable. - 86 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 97
    Archer C2 AC750 Wireless Dual Band Gigabit Router  MAC Address of Parental PC - In this field, enter the MAC address of the controlling PC, or you can make use of the Copy To Above button below.  MAC Address of Current PC - This field displays the MAC address of the PC that is managing this router
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 98
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-74 Parent Control Settings 4.15 Access Control Figure 4-75 Access Control - 88 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 99
    Archer C2 AC750 Wireless Dual Band Gigabit Router There are four submenus under the Access Control menu: Rule, Host, Target and Schedule (as shown in Figure 4-75). Click any of them, and you
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 100
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Delete Selected - Click the Delete Selected button to and choose "Allow the packets specified by any enabled access control policy to pass through the router". 2. We recommend that you click Add New button to finish all the following settings.
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 101
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4. Click the submenu Target of Access Control in the left to enter the Target List page. Add a new entry with the Target Description is Target_1
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 102
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Address Info - Here displays the information about the host. It can be IP or MAC.  Edit - To modify or delete an existing entry. Click the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 103
    Archer C2 AC750 Wireless Dual Band Gigabit Router 1. Click Add New button in Figure 4-78 to enter the Add or Modify a Host Entry page. 2. In Mode field, select MAC Address from the drop-
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 104
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-82 Add or Modify an Access Target Entry I) In Description field, create a unique description for the target (e.g. Target_1). II) In IP Address field, enter the IP address of the target. III) Specify the Target Port manually. 2） If you select
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 105
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-84 Add or Modify an Access Target Entry I) In Description field, create a unique description for the target (e.g. Target_1). II) In Add URL Address field,
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 106
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.15.4 Schedule Choose menu "Access Control → Schedule", and then you can view and set a Schedule list in the next screen as shown in Figure 4-85.
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 107
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-86 Advanced Schedule Settings For example: If you desire to restrict the internet activities of host with MAC address 00:11:22:33:44:
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 108
    Archer C2 AC750 Wireless Dual Band Gigabit Router There are two submenus under the Advanced Routing menu as shown in Figure 4-87: Static Route List and host portion.  Gateway - This is the IP Address of the gateway device that allows for contact between the router and the network or host. - 98 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 109
    Archer C2 AC750 Wireless Dual Band Gigabit Router 3. Select Enabled or Disabled for this entry on  Gateway - This is the IP address of the gateway device that allows for contact between the router and the network or host.  Interface - This interface tells you either the Destination IP Address is
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 110
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.17 Bandwidth Control Figure 4-91 Bandwidth Control Choose menu "Bandwidth Control", and then you can configure the bandwidth control in the screen as shown in
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 111
    Archer C2 AC750 Wireless Dual Band Gigabit Router 1. Click Add New shown in Figure 4-91, you will see a new screen shown in Figure 4-92. 2. Enter the information like the screen shown below. Figure 4-
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 112
    Archer C2 AC750 Wireless Dual Band Gigabit Router  MAC Address - The MAC address of the controlled computer in the LAN.  IP Address - The assigned IP address of the controlled computer in the LAN. 
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 113
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-96 ARP List 1. MAC Address - The MAC address of the , or www.no-ip.com. The Dynamic DNS client service provider will give you a password or key. 4.19.1 No-ip.com DDNS If the dynamic DNS Service Provider you select is www.no-ip.com, the page
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 114
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-97 No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the Domain Name you received from dynamic DNS service provider. 2. Enter the UserName for your DDNS account. 3. Enter the Password for your DDNS account. 4.
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 115
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-98 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the Domain Name your dynamic DNS service provider gave. 2. Enter the UserName for your DDNS account. 3. Enter the Password for your DDNS account. 4. Enable
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 116
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-99 Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the Domain Name you received from dynamic DNS service 20 IPv6 Figure 4-100 IPv6 Support There are three submenus under the IPv6 Support menu (shown in Figure
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 117
    4.20.1 IPv6 Status Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-101 IPv6 Status The IPv6 Status page displays the router's current IPv6 status and configuration. All information is read-only.  WAN  Connection Type - The IPv6 connection way for WAN  Connection Status - The status
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 118
    4.20.2 IPv6 WAN Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-102 Enable/Disable IPv6  Connection Type - Choose the correct WAN connection type based on your ISP network topology.  Dynamic IPv6 - Connections which use dynamic
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 119
    1) Dynamic IPv6 Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-103 Dynamic IPv6  IPv6 Address - The IPv6 address assigned by your ISP dynamically.  Prefix Length - The length of IPv6 address prefix.  IPv6 Gateway - Enter
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 120
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-104 Static IPv6  IPv6 Address - Enter the IPv6 address provided by your ISP.  Prefix Length - The length of IPv6 address prefix.  IPv6 Gateway - Enter
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 121
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-105 PPPoEv6  PPP Username/Password - Enter the User Name and Password ISP - Input a static IPv6 address from the ISP.  Set IPv6 DNS Server manually - Enter the IP address of the IPv6 DNS server and secondary IPv6 DNS server. - 111 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 122
    4) Tunnel 6to4 Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-106 Tunnel 6to4 This type is used in the situation that your WAN connection is IPv4 while LAN connection is IPv6.  WAN Connection - Display
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 123
    4.21 System Tools Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-108 The System Tools menu Choose menu "System Tools", and you can see the submenus under the main menu: Time Settings, Diagnostic, Firmware Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, System Log and
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 124
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Date - Enter your local date in MM/DD/YY into the in the second field, the day in the third field and the time in the last field. To set time manually: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 125
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-110 Time settings  Note: 1. This setting will be used for some time-based functions such as firewall. You must specify your time zone once you login to the router successfully, otherwise, these functions will not take effect. 2. The time
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 126
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Diagnostic Tool - Check the radio button to select one diagnostic too.  Ping - This diagnostic tool troubleshoots the domain name is not, you might have a name resolution problem. In this case, ensure that the domain name you are specifying
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 127
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.21.3 Firmware Upgrade Choose menu "System Tools → Firmware Upgrade", and then you can update the latest version of firmware for the router on the following screen. Figure 4-113 Firmware Upgrade  Firmware Version - Displays the current firmware
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 128
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.21.4 Factory Defaults Choose menu "System Tools → Factory Defaults", and then and you can restore the configurations of the router your local computer.  To upgrade the router's configuration, follow these instructions.  Click the Browse button to
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 129
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Click the Restore button to update the configuration with (system will reboot automatically).  Upgrade the firmware of the router (system will reboot automatically).  Restore the router's settings to factory defaults (system will reboot
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 130
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure 4-117 Password It is strongly recommended that you should change the factory default user name and password of the router, because all users who try to access the router's Web-based utility or Quick Setup will be prompted for the router's
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 131
    Archer C2 AC750 Wireless Dual Band Gigabit Router  Log Settings - Click to change the log settings. 4.21.9 Statistics Choose menu "System Tools → Statistics", and then you can view the statistics of the router, including total traffic and current traffic of the last Packets Statistic Interval.
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 132
    Archer C2 AC750 Wireless Dual Band Gigabit Router Statistics Table: IP/MAC Address The IP and MAC address are displayed with related statistics. Total The total number of packets received and transmitted by the Packets router. Bytes The total number of bytes received and transmitted by the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 133
    Archer C2 AC750 Wireless Dual Band Gigabit Router 4.22 Logout Choose "Logout", and you will be back to the login screen as shown in Figure 4-119. Figure 4-119 Logout - 123 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 134
    Archer C2 AC750 Wireless Dual Band Gigabit Router Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the Internet port on the router manually"
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 135
    Archer C2 AC750 Wireless Dual Band Gigabit Router 2. How do I configure the router to access Internet by Ethernet users? 1) Login to the router router and click the "Network" menu link on the left of your browser, and then click "MAC Clone" submenu link "1720" for the "Service Port" blank, and your
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 136
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure A-4 Virtual Servers Figure A-5 Add or Modify a Virtual server Entry  Note: Your opposite side should call your WAN IP, which is displayed on the "Status" page. 4) How to enable DMZ Host: Log in to the router, click the "Forwarding" menu on
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 137
    Archer C2 AC750 Wireless Dual Band Gigabit Router Figure A-7 Basic Security 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the router port number: Log in to the router, click the "Security" menu on the
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 138
    Archer C2 AC750 Wireless Dual Band Gigabit Router field of the Web browser. If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the router Server" page, enter "80" into the blank next to the "Service Port", and your IP address next to the "IP Address", assuming
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 139
    Archer C2 AC750 Wireless Dual Band Gigabit Router Appendix B: Configuring the PC In this section, we'll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter's manual if needed. 1. Install TCP/IP component 1)
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 140
    Archer C2 AC750 Wireless Dual Band Gigabit Router 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. 6) Select Obtain an IP address automatically and Obtain DNS server automatically, as shown in the Figure below: Figure B-3 - 130 -
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 141
    Archer C2 AC750 Wireless Dual Band Gigabit Router Appendix C: Specifications General Standards Protocols IEEE Internet RJ45 port; 4 10/100/1000M Auto-Negotiation Ethernet RJ45 ports supporting Auto MDI/MDIX; 1 USB port supporting storage/FTP/Media/Print Server; 10BASE-T: UTP category 3, 4, 5 cable
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 142
    Archer C2 AC750 Wireless Dual Band Gigabit Router Appendix D: Glossary  802.11ac - IEEE 802.11ac be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing.  DNS (Domain Name System) - An Internet Service that translates the names of websites into IP
  • TP-Link Archer C2 | Archer C2 V1 User Guide 1910010993 - Page 143
    Archer C2 AC750 Wireless Dual Band Gigabit Router  MTU (Maximum Transmission Unit) - The size in bytes of the over an always-on connection by simulating a dial-up connection.  SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
REV1.0.0
1910010993