Pyle SLPRWAS23 Instruction Manual
Pyle SLPRWAS23 Manual
 |
View all Pyle SLPRWAS23 manuals
Add to My Manuals
Save this manual to your list of manuals |
Pyle SLPRWAS23 manual content summary:
- Pyle SLPRWAS23 | Instruction Manual - Page 1
1. Safety valve worn out 2.Pump,high pressure hose, trigger gun is leaking 1. Contact the nearest service center 2.Contact the nearest service center The content in this instruction manual (include accessories) is kept the nal modifying and explanation rights This machine is designed for domestic - Pyle SLPRWAS23 | Instruction Manual - Page 2
up pressure within two minutes, switch it o and proceed as instructed in the Chapter "Troubleshooting". The trigger gun is subjected to recoil force when the water stations) all ofthe safety provisions and operating instructions detailed in this manual must be observed. 6. Never use the appliance
-
1 -
2
 |
 |
by
WARNING:
Do not use the appliance before reading the instruction manual
This
machine is designed for domestic use only
SLPRWAS23
HIGH PRESSURE WASHER
User Manual
Appliance is leaking
Slight leakage from the appliance pump is normal. lf the leakage increases
contract the authorized customer service.
Storage
In orderto prevent accidents or injuries, keep in mind the weight of the
appliance, pull out the telescopic rod (max length 410mm) when selecting
a storage location for it.
Storing the appliance
1. Park the machine on an even surface.
2. Press the disconnect on the trigger gun and remove the high pressure
hose from the trigger gun.
3. Push the casing of coupling forthe high pressure hose toward the rear
and disconnect the high pressure hose from the appliance.
4. lnsert the trigger gun into the holder.
5. Stow away the mains cable, the high pressure hose and accessories on
the appliance.
Prior to extended storage periods, as during the winter, also observe the
instructions in the care section.
Specification
Model No: SLPRWAS23
Power Supply: 110V
Power: 1200 Watt
Max pressure: Up to 1160+ psi
Water Flow: 300L / per Hour (5L/ per Min.)
Max water pressure:
80bar (8Mpa)
Working pressure: 6.5Mpa
Water temperature: 32-140° F
Environment temperature: 41-122° F
Weight: 14.35 lbs.
Length: 8.5 in
Width: 7.6 in
Height: 17.0 in
Symptom
Cause
Recommended
action
Machine refused to
start
1.Machine
not
plugged
in
2.Defectiv
e
socket
3.Defective extension
cable
4.1ncorrect mains
voltage
5.Switch
off
6.Fuse
has
blown
1. Plug
in
machine
2.Try
another socket
3.Try
anothe
r
extension
cable
4.Check
voltage correctly
5.Turn on
switch
6.Replace
fuse
Pump stop
working
Lack of water lead
to
high
temperature
check
water flow
quantity
-put the hose in the
10
bottle (per
minute
)
Fluctuatin
g
pressure
1.Spray
lance
blocked
2. Pump is
sucking
air
3.
Impurities
in
pump
1. Clean lance
with
needle
2.Check
that hoses
and
connections
are
airtight
3.Contact
the
dealer
Machine do not
reach
operation
pressure
1.Spray lance blocked or
worn
2.Short supply
of
water
3.Hose
kinked
4.Filter blocked
5.Hose blocked
1. Clean
or change
spray
lance
2.Check
inlet flow
rate
3.Straighte
n
out
hose
4.Ciean
filter
5.Ciean hose
Trigger gun can be
used
Trigger gun is
locked
Unlock
trigger gun
Machine often starts
and
stops by
itself
1. Safety valve worn
out
2.Pump,high pressure
hose,
trigger
gun
is
leaking
1.
Contact
the
nearest
service center
2.Contact
the
nearest
service center
Troubleshooting
The content in this instruction manual (include accessories) is kept the final
modifying and explanation rights
1
10
9
2
A
B
C
F
E
D
G
H
I
J
11
www.PyleUSA.com
www.PyleUSA.com
www.PyleUSA.com
www.PyleUSA.com
www.PyleUSA.com