Palsonic VCR9688 Owners Manual

Palsonic VCR9688 Manual

Get Palsonic VCR9688 PDF manuals and user guides View all Palsonic VCR9688 manuals
Add to My Manuals
Save this manual to your list of manuals

Palsonic VCR9688 manual content summary:

  • Palsonic VCR9688 | Owners Manual - Page 1
    OWNER'S MANUAL VIDEO CASSETTE RECORDER VCR-9688 G-CODE Type Tested Electrical Safety AS/NZS 3250 Lic 4168 Standards Australia
  • Palsonic VCR9688 | Owners Manual - Page 2
    before using the VCR and store it in a safe place for future reference. This Owner's Manual explains how to use your VCR and, in particular, using the remote control unit keys to control indicated in the diagram below and refer to the illustration while reading the appropriate section of the manual.
  • Palsonic VCR9688 | Owners Manual - Page 3
    Remote control unit
  • Palsonic VCR9688 | Owners Manual - Page 4
    Front panel IDENTIFICATION OF CONTROLS Rear panel Multi-display
  • Palsonic VCR9688 | Owners Manual - Page 5
    V V Front Panel REMOTE SENSOR Multi-display REC.button (REC/OTR) CHANNEL V/ buttons STOP/EJECT button FF button PLAY button REW button Cassette loading slot OPERATE/TIMER button Rear Panel AC Mains cord CLEAR button TEST SIGNAL switch AUDIO OUT Jack AUDIO IN Jack RF OUT socket CH ADJ (RF CHANNEL
  • Palsonic VCR9688 | Owners Manual - Page 6
    EQUIPMENT TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. MAINTAIN GOOD VENTILATION There are many ventilation holes on the bottom of the VCR. For maximum ventilation place the
  • Palsonic VCR9688 | Owners Manual - Page 7
    E-19 E-20 E-21 E-22 ACCESSORIES Before installing your VCR, please check you have the following items. Coaxial Cable Remote Control Unit Owner's Manual Moisture Condensation Never operate this unit immediately after moving it from a cold location to a warm location. When the VCR is exposed to
  • Palsonic VCR9688 | Owners Manual - Page 8
    INTRODUCTION Remote Control Operation This VCR can be operated with the remote control from up to a distance of about 23 feet (7 meters) and within an angle of 15 degrees either side of center. There must be no obstacles between the remote control unit and the remote sensor of the VCR. Loading and
  • Palsonic VCR9688 | Owners Manual - Page 9
    INSTALLATION Equipment Connection TV Antenna To watch a picture from the VCR using this connection, it is necessary to set one of the TV channels as the "Video channel". See Preparations in Video Channel Setting (on Page 6). 1. Connect the antenna (or CATV) connector to the ANT. IN socket. 2.
  • Palsonic VCR9688 | Owners Manual - Page 10
    PREPARATIONS Video Channel Setting Initial Settings This setting is necessary for RF connections (when the SCART cable is not used to connect this unit and the TV). This setting is not necessary for AV connections using the SCART cable. Start from the initial Settings in the next section. When
  • Palsonic VCR9688 | Owners Manual - Page 11
    V V 1. Set the On-screen Language . Initial Setting Up 1. Select the language you want by using the buttons to display it inverted. 2. When you press the MENU button, that language is set and the CLOCK SET screen appears automatically. . Changing the Language after the Initial Settings 1. Press the
  • Palsonic VCR9688 | Owners Manual - Page 12
    V V Menu Screen/Mode Screen . Using the Menu Screen When you press the MENU button, the menu screen is called up. When you press the MENU button again, the unit returns to the normal screen. Select the item you want by using the buttons to highlight its screen setting, then press the SHIFT>
  • Palsonic VCR9688 | Owners Manual - Page 13
    two ways to preset channels: Automatic tuning with AMS and manual tuning. AMS Operation Automatic tuning with AMS is executed since Channel 045 is already at Position 01 Channel 022 is swapped to Position 01. Manual Tuning Manual tuning is used when there is a channel that was not preset by AMS or
  • Palsonic VCR9688 | Owners Manual - Page 14
    the initial setting for G-Code programming, prepare the list below. For all TV stations you have stored on the VCR following the procedure by AMS/Manual tuning, fill in the blanks with the position number you used, and the corresponding TV stations. For G-Code programming procedure, see page 19
  • Palsonic VCR9688 | Owners Manual - Page 15
    CHANNEL SELECTION V Tuning with the V CH Buttons 1. Press the OPERATE/TIMER button to turn on the VCR. 2. Press the buttons to select the position number to which the desired channel has been preset. P10 .Notes If the buttons are pressed and immediately released, the preset position steps
  • Palsonic VCR9688 | Owners Manual - Page 16
    tracking If video noise appears in the picture after putting the VCR into Auto tracking mode, use the Manual tracking adjustment function. Press the buttons until the best possible picture is obtained. To return to Auto tracking mode, press the PLAY button for more
  • Palsonic VCR9688 | Owners Manual - Page 17
    SPECIAL EFFECT PLAYBACK Search The Picture Search function is a convenient way to locate a desired portion of the tape quickly. Forward Search: To view high-speed pictures in the forward direction 1. In the Playback mode, press the FF button. 2. Press the FF button again to search faster. 3. To
  • Palsonic VCR9688 | Owners Manual - Page 18
    1 Minute Skip With this feature you can skip over one minute's worth of .commercials recorded on a tape. Pressing the SKIP/ZERO RTN button in Play mode to forward search the tape for 60 seconds, then returns . the VCR to Play mode. Pressing the SK/P/ZERO RTN button while it is fast forwarding
  • Palsonic VCR9688 | Owners Manual - Page 19
    RECORDING Basic Operation 1. Press the OPERATE/TIMER button. 2. Press the buttons to select a desired channel to be recorded. 3. Insert a cassette tape with a safety tab. 4. Press the REC button to start recording. 5. To finish recording, press the STOP/EJECTbutton. Checking the Picture
  • Palsonic VCR9688 | Owners Manual - Page 20
    One-touch Timer Recording (OTR) This allows you record for up to 5 hours with automatic turn-off. 1. Press the REC button during recording. The VCR enters OTR mode. 2. Select the recording duration by pressing the REC button repeatedly. The OTR indication appears on the TV screen. The OTR recording
  • Palsonic VCR9688 | Owners Manual - Page 21
    PROGRAMMABLE TIMER RECORDING A maximum of 8 events can be programmed within a period of one month including the present day for timer recording. A timer recording can be activated at the same time on the same day every week, on every day or on weekdays, as well as on a particular day. Program
  • Palsonic VCR9688 | Owners Manual - Page 22
    V V Hints on Programming In Step 4, you can select various "EV" (every week) recording of the same channel at the same time modes as well as recording on a particular day. Press the V button when the current day on the calendar blinks or press the button, exceeding the last day of the calendar (the
  • Palsonic VCR9688 | Owners Manual - Page 23
    G-Code INSTANT VIDEO PROGRAMMING G-Code program can record a program by using the GCode numbers (up to 9 digits) in newspaper and magazine TV listings to set the VCR. G-Code Programming 1. Press the G-CODE button to call up the G-Code screen. G-Code is a trademark applied for by Gemstar
  • Palsonic VCR9688 | Owners Manual - Page 24
    5. Use the screen below to check the settings. If this is the first time G-Code has been used for a channel, use the buttons to enter the position number. Refer to the table on page 10 for details. This setting is only required the first time. The POS settings can be changed. Use the < SHIFT
  • Palsonic VCR9688 | Owners Manual - Page 25
    OTHERS Check the following list of problems and remedies before calling service personnel. The problem may be one you can solve yourself. SYMPTOM CAUSE No power supply to the VCR. AC Mains Cord is not connected. REMEDY Connect the AC
  • Palsonic VCR9688 | Owners Manual - Page 26
    SPECIFICATIONS GENERAL SECTION Power Requirements Power Consumption Dimensions (W x H x D) Weight Operating Temperature Operating Humidity Video Recording System Number of Video Heads Tape Speed Tape Format Record/Playback Time 230V AC ~ 50 Hz 16 Watts 370 x 95.5 x 271 mm Approx. 3.6 kg. 5°Ct o
  • Palsonic VCR9688 | Owners Manual - Page 27
    PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
VCR-9688
OWNER’S MANUAL
VIDEO CASSETTE RECORDER
G-
CODE
Type Tested
Electrical
Safety
AS/NZS 3250 Lic 4168
Standards
Australia