Home » Makita Manuals » Tools » Makita 5057KB » Manual Viewer

Makita 5057KB Owners Manual

Makita 5057KB Manual

View all Makita 5057KB manuals

Add to My Manuals
Save this manual to your list of manuals

Makita 5057KB manual content summary:

Makita 5057KB | Owners Manual - Page 1
Circular Saw with Dust Collection 185 mm (7-1/4") MODEL 5057KB DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. www.makitatools.com
Makita 5057KB | Owners Manual - Page 2
Model Blade diameter Max. Cutting depth at 90° at 45° No load speed (RPM) Overall length Net weight 5057KB and understand all instructions. Failure to follow all instructions listed below, may liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep
Makita 5057KB | Owners Manual - Page 3
equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard clamps or other practical way to secure and support the workpiece to a stable platform. Holding the parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced
Makita 5057KB | Owners Manual - Page 4
servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions gained from repeated use) replace strict adherence to circular saw safety rules. If you use this tool unsafely
Makita 5057KB | Owners Manual - Page 5
the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris. 4. Lower guard should be retracted manually only for special cuts such as "Pocket Cuts" and "Compound Cuts." Raise
Makita 5057KB | Owners Manual - Page 6
is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted. Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and
Makita 5057KB | Owners Manual - Page 7
attempt to saw with the circular saw held upside down in a vise. This is extremely dangerous and can lead to serious accidents. Fig. 4 A typical illustration of proper hand support, workpiece support, and supply cord routing. 16. Place the wider portion of the saw base on that part of the workpiece
Makita 5057KB | Owners Manual - Page 8
WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD201-2 The followings show the symbols used for tool. V volts A amperes n no load speed Class II Construction Hz hertz
Makita 5057KB | Owners Manual - Page 9
2. Lever 001345 Adjusting depth of cut CAUTION: • After adjusting the depth of cut, always tighten the lever securely. 2 Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base by tightening the lever. For cleaner, safer cuts, set
Makita 5057KB | Owners Manual - Page 10
to collect dust and cut chips. When the dust box is about two thirds full, empty its contents. To do so, press the lever to unlock the dust cap and open it. Tip the rear of the tool down to empty the dust box. Cleaner cutting operations can be performed by connecting this tool to Makita
Makita 5057KB | Owners Manual - Page 11
Screws 001413 Removing or installing saw blade 1 CAUTION: • Be sure the blade is installed with teeth pointing up at the front of the tool. • Use only the Makita wrench to install or remove the blade. To remove the blade, first remove the clamping screws which secure the dust box, then remove the
Makita 5057KB | Owners Manual - Page 12
to chips and wood dust being ejected from saw. Use eye protection to help avoid injury. 1 1. Rip fence (Guide rule) 001485 Rip fence (Guide rule) The handy rip you start the cut. • Lower guard should be retracted manually only for special cuts such as "Pocket Cuts" and "Compound Cuts." Raise lower guard
Makita 5057KB | Owners Manual - Page 13
001494 1 as blade enters the material, retracting lever must be released. For all other sawing, the lower guard should operate automatically. Tilt the tool forward and rest the front of the base on the workpiece to be cut. Using the
Makita 5057KB | Owners Manual - Page 14
maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or
Makita 5057KB | Owners Manual - Page 15
Memo 15
Makita 5057KB | Owners Manual - Page 16
Memo 16
Makita 5057KB | Owners Manual - Page 17
Cut Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 First-Class Postage Required Post Office will not deliver without proper postage. Fold 17
Makita 5057KB | Owners Manual - Page 18
Most favored points are: Design Features Size Price Makita Brand Repair Service Durability Power Other ( ) 5. Any comments: Paste Paste Paste Paste Paste Paste Paste Paste DATE PURCHASED MONTH DAY YEAR MODEL
Makita 5057KB | Owners Manual - Page 19
When you need service: Send complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to an Authorized Makita Service Center. Be sure to attach a letter to the outside of the carton detailing the problem with your tool. Date Purchased Dealer's Name & Address Model No. Serial
Makita 5057KB | Owners Manual - Page 20
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains freight prepaid, to one of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our