LiftMaster EL1SS EL1SS Repair Parts Instructions Manual

LiftMaster EL1SS Manual

Get LiftMaster EL1SS PDF manuals and user guides View all LiftMaster EL1SS manuals
Add to My Manuals
Save this manual to your list of manuals

LiftMaster EL1SS manual content summary:

  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 1
    EL1SS TELEPHONE ENTRY SYSTEM REPAIR PARTS INSTRUCTIONS Replace the Logic Board NOTE: After the new logic board is installed all site data must be reentered into the EL1SS system the logic board to LiftMaster. 7. Place a plastic service. Figure 1 Figure 2 Nut Faceplate Figure 3 Screw
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 2
    replacement, DO NOT discard the keypad. If applicable, return the keypad to LiftMaster. 9. Secure the new keypad and keypad bracket to the faceplate using lock and secured. At that time the unit may be returned to service. Figure 1 Figure 2 Nut Faceplate Figure 3 Plastic Washer Screw Logic Board
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 3
    by a qualified individual. • Upon completion of kit installation, the area MUST be cleared and secured. At that time the unit may be returned to service. Figure 1 Figure 2 Nut Faceplate Figure 3 Figure 4 Logic Board Speaker Cable Screw Plastic Washer Figure 5 Speaker Cable Lock Nut Speaker 3
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 4
    by a qualified individual. • Upon completion of kit installation, the area MUST be cleared and secured. At that time the unit may be returned to service. Figure 1 Figure 2 Nut Figure 3 Logic Board Screw Plastic Washer Figure 4 Lock Nut Keypad Bracket Figure 5 Lock Nut Standoff Call Button 4
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 5
    EL1SS INSTRUCTIONS POUR PIÈCES DE RÉPARATION REMARQUE : Après l'installation de la carte logique neuve, toutes les données du site doivent être de nouveau entrées dans le système EL1SS retourner la carte logique à LiftMaster. 7. Placer une rondelle service. Figure 1 Figure 2 Écrou
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 6
    le pavé. S'il y a lieu, retourner le pavé à LiftMaster. 9. Fixer la pavé neuf et le support du pavé à la plaque avant avec les contre-écrous. 10. Ce n'est qu'à ce moment que l'unité peut être remise en service. Figure 1 Figure 2 Écrou Plaque frontale Figure 3 Rondelle de plastique Vis Carte logique
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 7
    l'installation du nécessaire d'isolation, la zone DOIT être dégagée et sécurisée. Ce n'est qu'à ce moment que l'unité peut être remise en service. Figure 1 Figure 2 Écrou Plaque frontale Figure 3 Figure 4 Carte logique Câble du haut-parleur Vis Rondelle de plastique Figure 5 Câble du haut-parleur
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 8
    , la zone DOIT être dégagée et sécurisée. Ce n'est qu'à ce moment que l'unité peut être remise en service. Figure 1 Figure 2 Écrou Figure 3 Carte logique Vis Rondelle de plastique Figure 4 Contre-écrou Support de pavé Figure 5 Contre-écrou Douille-entretoise autosertissable Bouton d'appel 4
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 9
    REPUESTOS NOTA: Una vez cambiada la tarjeta debe cargarse al sistema EL1SS todos los datos del sitio. 1. Desconectar la alimentación elé por garantía, NO desechar la tarjeta lógica. Devolver la tarjeta lógica a LiftMaster si esas fueran las instrucciones. 7. Colocar la arandela de plástico en cada
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 10
    vigentes para productos eléctricos (Figura 4). NOTA: Si este fuera un cambio por garantía, NO desechar el teclado. Devolver el teclado a LiftMaster si esas fueran las instrucciones. 9. Fijar el teclado a la placa frontal con las tuercas correspondientes. 10. Colocar la arandela de plástico
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 11
    Instalar el altavoz 1. Desconectar la alimentación eléctrica del . 2. Liberar la placa frontal (Figura 1). 3. Desconectar todos los cables de la tarjeta lógica. Observar la posición de los cables para volver a conectarlos. 4. Quitar las tuercas (3) de la placa frontal y hacerlas a un lado.
  • LiftMaster EL1SS | EL1SS Repair Parts Instructions Manual - Page 12
    lógica Tornillo Arandela de plástico Figura 4 Tuerca de fijación Soporte del teclado 01-37890 Figura 5 Tuerca de fijación Separador vertical Botón de llamada © 2015, LiftMaster All Rights Reserved Tous droits réservés Todos los derechos reservados
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
Replace the Logic Board
NOTE:
After the new logic board is installed all site data must be
reentered into the EL1SS system.
1. Disconnect power to the unit.
2. Unlock the faceplate (Figure 1).
3. Disconnect all the wires from the logic board. Make note of the
wire locations for reassembly.
4. Remove the nuts (3) securing the faceplate to the housing and set
aside. Carefully remove the faceplate (Figure 2).
5. Place the faceplate on a flat surface and prop the faceplate up so
the faceplate is flat.
6. Remove the screws (4) securing the existing logic board from the
faceplate. Remove the existing logic board and discard in
accordance with local electrical disposal guidelines (Figure 3).
NOTE:
If this is an in warranty replacement, DO NOT discard the
logic board. If applicable, return the logic board to LiftMaster.
7. Place a plastic washer over each of the metal standoffs. The
plastic washers MUST be installed to prevent the stand offs from
shorting out the logic board when power is reconnected.
NOTE:
To help keep the components in place, insert a toothpick or short
length of wire into the standoff and slide the components over the
toothpick or short length of wire.
8. Position the new logic board on to the faceplate.
9. Place a plastic washer over the mounting holes (4) in the logic
board. If applicable, carefully remove the toothpicks or short
length of wire.
10. Fasten the new logic board to the faceplate with screws (4).
11. Reattach the faceplate to the housing using the previously
removed nuts (3).
12. Reconnect all the wires to the logic board.
13. Close the faceplate.
14. Reconnect power to the unit.
15. Reenter site data and test.
To reduce the risk of SERIOUS INJURY or DEATH:
• Disconnect electric power at the fuse box BEFORE proceeding.
•
ALL electrical connections MUST be made by a qualified
individual.
•
Upon completion of kit installation, the area MUST be cleared
and secured. At that time the unit may be returned to service.
Nut
Screw
Logic Board
Faceplate
Plastic
Washer
Figure 1
Figure 2
Figure 3
EL1SS TELEPHONE ENTRY SYSTEM
REPAIR PARTS INSTRUCTIONS