LiftMaster 3265-267 3265 Manual

LiftMaster 3265-267 Manual

Get LiftMaster 3265-267 PDF manuals and user guides View all LiftMaster 3265-267 manuals
Add to My Manuals
Save this manual to your list of manuals

LiftMaster 3265-267 manual content summary:

  • LiftMaster 3265-267 | 3265 Manual - Page 1
    DOOR OPENER Model 3265 1/2 HP For Residential Use Only The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com Owner's Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation
  • LiftMaster 3265-267 | 3265 Manual - Page 2
    Parts and Service 36 Warranty 36 INTRODUCTION Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual
  • LiftMaster 3265-267 | 3265 Manual - Page 3
    to garage door and opener: • ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage. Sectional Door One-Piece Door Tools needed During assembly, installation and adjustment of the opener, instructions will
  • LiftMaster 3265-267 | 3265 Manual - Page 4
    you proceed with the installation of your opener. SECTIONAL DOOR INSTALLATION Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 19 for details. Header Wall FINISHED CEILING Support bracket & fastening
  • LiftMaster 3265-267 | 3265 Manual - Page 5
    Inventory Your garage door opener is packaged in two cartons which If anything is missing, carefully check the packing material. contain the motor unit and all parts illustrated below. Parts may be stuck in the foam. Hardware for installation Accessories will depend on the model purchased. is
  • LiftMaster 3265-267 | 3265 Manual - Page 6
    ASSEMBLY STEP 1 Attach the Rail to the Motor Unit To avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. • Position rail at a 45˚ angle to opener so one hole in rail and motor unit line up. •
  • LiftMaster 3265-267 | 3265 Manual - Page 7
    connect garage door opener to power source until instructed to do so. 8. NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught in garage door or opener mechanisms. 9. Install wall-mounted garage door control: • within sight of the garage door. • out
  • LiftMaster 3265-267 | 3265 Manual - Page 8
    CEILING MOUNT FOR HEADER BRACKET Structural Supports Level (optional) Installation procedures vary according to garage door types. Follow the instructions which apply to your door. 1. Close the door and mark the inside vertical centerline of the garage door. 2. Extend the line onto the header
  • LiftMaster 3265-267 | 3265 Manual - Page 9
    garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing pilot holes and fasten bracket securely to a structural support with the hardware provided. Ceiling Mounting Holes CEILING MOUNT
  • LiftMaster 3265-267 | 3265 Manual - Page 10
    Bracket INSTALLATION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you will need help. Have someone hold the opener securely on a temporary support to
  • LiftMaster 3265-267 | 3265 Manual - Page 11
    trolley toward the motor unit. The trolley can remain disconnected until Installation Step 12 is completed. To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. Rail Door 2x4 is used to determine the correct mounting height from ceiling. ENGAGED
  • LiftMaster 3265-267 | 3265 Manual - Page 12
    at this time. To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural supports of the garage. Concrete anchors MUST be used if installing ANY brackets into masonry. Figure 1 Structural Supports Measure Distance Bolt 5/16"-18x7/8" Lock Washer 5/16" Nut
  • LiftMaster 3265-267 | 3265 Manual - Page 13
    SERIOUS INJURY or DEATH from a closing garage door: • Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door. • NEVER permit children to operate or play with door control push buttons or remote control
  • LiftMaster 3265-267 | 3265 Manual - Page 14
    due to vibration, replace with a Garage Door Opener bulb. • Use A19, standard neck garage door opener bulbs for replacement. NOTE: Use only ) Standard Light Bulb 100 Watt (Max) Standard Light Bulb Lens Hinge INSTALLATION STEP 8 Attach the Emergency Release Rope and Handle • Thread one end
  • LiftMaster 3265-267 | 3265 Manual - Page 15
    or DEATH from electrocution or fire: • Be sure power is not connected to the opener, and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection. • Garage door installation and wiring MUST be in compliance with ALL local electrical and building codes. • NEVER
  • LiftMaster 3265-267 | 3265 Manual - Page 16
    door is closing, the door will stop and reverse to full open position, and the opener lights will flash 10 times. The units must be installed inside the garage . No part of the garage door (or door tracks, springs, hinges, rollers or other hardware) may interrupt the beam while the door is closing
  • LiftMaster 3265-267 | 3265 Manual - Page 17
    Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the floor. They may be installed in one of three ways, as follows. Garage door track installation (preferred) (Figure
  • LiftMaster 3265-267 | 3265 Manual - Page 18
    to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension TROUBLESHOOTING THE SAFETY REVERSING SENSORS 1. If the sending eye indicator light does not glow steadily after installation, check for: • Electric power to the opener
  • LiftMaster 3265-267 | 3265 Manual - Page 19
    brace. For the vertical brace, 2 pieces of angle iron are used to create a U-shaped support. The best solution is to check with your garage door manufacturer for an opener installation door reinforcement kit. NOTE: Many door reinforcement kits provide for direct attachment of the clevis pin and
  • LiftMaster 3265-267 | 3265 Manual - Page 20
    for your installation. (Refer to the dotted line optional placement drawing.) HARDWARE SHOWN ACTUAL SIZE Self-Threading Screw 1/4"-14x5/8" Header Wall 2x4 Support Finished Ceiling Header Bracket Door Bracket Optional Placement of Door Bracket Vertical Centerline of Garage Door HORIZONTAL AND
  • LiftMaster 3265-267 | 3265 Manual - Page 21
    INSTALLATION STEP 12 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONLY • Make sure garage door and nuts. • Pull the emergency release handle toward the opener at a 45° angle so that the trolley release
  • LiftMaster 3265-267 | 3265 Manual - Page 22
    Turn the UP limit adjustment screw counter-clockwise 4 turns. - Press the Door Control push button. The trolley will travel to the fully open position. - Manually raise the door to the open position (parallel to the floor), and lift the door arm to the trolley. The arm should touch the trolley just
  • LiftMaster 3265-267 | 3265 Manual - Page 23
    Sensors are either not installed, misaligned, or obstructed. See Troubleshooting, page 18. Test the door for binding: Pull the emergency release handle. Manually open and close the door. If the door is binding or unbalanced, call for a trained door systems technician. If the door is balanced and not
  • LiftMaster 3265-267 | 3265 Manual - Page 24
    required to open and close the door. If the forces are set too light, door travel may doors), it will reverse. Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Too much force on garage door
  • LiftMaster 3265-267 | 3265 Manual - Page 25
    , or force controls. • Any repair to or adjustment of the garage door (including springs and hardware). • Any repair to or buckling of the garage floor. • Any repair to or adjustment of the opener. Without a properly installed safety reversal system, persons (particularly small children) could be
  • LiftMaster 3265-267 | 3265 Manual - Page 26
    under EXTREME tension, MUST be made by a trained door systems technician. 14. ALWAYS disconnect electric power to garage door opener BEFORE making ANY repairs or removing covers. 15. SAVE THESE INSTRUCTIONS. Using Your Garage Door Opener Your Security✚® opener and hand-held remote control have been
  • LiftMaster 3265-267 | 3265 Manual - Page 27
    Press and hold the Lock button on the door control. 3. Press and hold the door control push bar. 4. After the opener lights flash, release all buttons. To Open the Door Manually To prevent possible SERIOUS INJURY or DEATH from a falling garage door: • If possible, use emergency release handle to
  • LiftMaster 3265-267 | 3265 Manual - Page 28
    a Month • Manually operate door. If it is unbalanced or binding, call a trained door systems technician. • Check to be sure door opens and closes fully. the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE.
  • LiftMaster 3265-267 | 3265 Manual - Page 29
    HAVING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • Verify the safety sensors are properly installed, aligned and free of any
  • LiftMaster 3265-267 | 3265 Manual - Page 30
    Bell Wire Diagnostics Located On Motor Unit Installed Safety Reversing Sensor Safety Reversing Sensor LED or Diagnostic LED "Learn" Button Diagnostic Chart Your garage door opener is programmed with self-diagnostic capabilities. The "Learn" button/diagnostic LED will flash a number of times
  • LiftMaster 3265-267 | 3265 Manual - Page 31
    that technical measure. Your garage door opener has already been programmed at the factory to operate with your hand-held remote control. The door will open and close when you press the large push button. Below are instructions for programming your opener to operate with additional Security
  • LiftMaster 3265-267 | 3265 Manual - Page 32
    operate your garage door opener. USING THE "LEARN" BUTTON USING THE MULTI-FUNCTION DOOR CONTROL LOCK learned the code. If light bulbs are not installed, two clicks will be heard. To change an The door should move. To set a temporary PIN You may authorize access by visitors or service people with
  • LiftMaster 3265-267 | 3265 Manual - Page 33
    KEY PART NO. NO. DESCRIPTION 1 41A5273-1 Multi-function door door arm section 11 178B35 Curved door arm section 12 41A5266-1 Safety sensor brackets (2) NOT SHOWN 41A2770-6 Installation hardware bag (includes hardware listed on page 5). 114A3044 Owner's manual 114A3044SP Owner's manual
  • LiftMaster 3265-267 | 3265 Manual - Page 34
    bracket, bearing assembly, RPM sensor KEY NO. 12 13 14 15 16 17 PART NO. 41A5525-1 41A2818 41D3452 41A2822-1 41C4398A 41AC050 18 41C5498 41C5497 19 41D180-1 labels NOT SHOWN Motor shaft bearing kit Opener assembly hardware kit (includes screws not designated by a number in illustration) 34
  • LiftMaster 3265-267 | 3265 Manual - Page 35
    ACCESSORIES 1702LM Outside Quick Release: Required for a garage with NO access door. Enables homeowner to open garage door manually from outside by disengaging trolley. 395LM 41A5281 Extension Brackets: (Optional) For safety sensor installation onto the wall or floor. 373W Remote Light
  • LiftMaster 3265-267 | 3265 Manual - Page 36
    : 1-800-528-9131 www.liftmaster.com For professional installation, parts and service, contact your local LIFTMASTER/CHAMBERLAIN dealer. Look for him in the Yellow Pages, or call our Service number for a list of dealers in your area. HOW TO ORDER REPAIR PARTS Selling prices will be furnished on
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.liftmaster.com
GARAGE DOOR OPENER
Model 3265 1/2 HP
For Residential Use Only
Owner’s Manual
■
Please read this manual and the enclosed safety materials carefully!
■
Fasten the manual near the garage door after installation.
■
The door WILL NOT CLOSE unless the Protector System
®
is connected and properly
aligned.
■
Periodic checks of the opener are required to ensure safe operation.
■
The model number label is located on the front panel of your opener.
®