LevelOne WAB-6120 Manual

LevelOne WAB-6120 Manual

Get LevelOne WAB-6120 PDF manuals and user guides View all LevelOne WAB-6120 manuals
Add to My Manuals
Save this manual to your list of manuals

LevelOne WAB-6120 manual content summary:

  • LevelOne WAB-6120 | Manual - Page 1
    LevelOne WAB-6120 150Mbps Wireless Outdoor PoE AP User Manual V1.2
  • LevelOne WAB-6120 | Manual - Page 2
    This user manual is intended to guide professional installer to install the LEVELONE 150MBPS WIRELESS POE AP and how to build the infrastructure centered on it. It includes procedures to assist you in avoiding unforeseen problems. Conventions For your attention on important parts, special characters
  • LevelOne WAB-6120 | Manual - Page 3
    and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase
  • LevelOne WAB-6120 | Manual - Page 4
    operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
  • LevelOne WAB-6120 | Manual - Page 5
    Standard hardware warranty is for one (1) year from date of shipment from Distributor. Warrants that hardware will conform to the current relevant published specifications and will be free from material defects in material and workmanship under normal use and service. IN NO EVENT SHALL DISTRIBUTOR
  • LevelOne WAB-6120 | Manual - Page 6
    System Requirements ...14 How to Login the Web-based Interface 14 Basic System Settings ...17 Time Settings ...20 RADIUS Settings ...21 Firewall Settings ...22 Basic Wireless Settings ...25 Site Survey ...28 VAP Profile Settings...29 VLAN Tab...30
  • LevelOne WAB-6120 | Manual - Page 7
    ...32 Advanced Wireless Settings...32 Wireless Security Settings...34 Security Settings ...34 Access Control ...37 WDS Settings...38 Chapter 5 Management...39 Remote Management ...39 SNMP Management ...39 Configure SNMPv3 User Profile 41 Coovachilli Settings ...42 Upgrade Firmware ...43 Backup
  • LevelOne WAB-6120 | Manual - Page 8
    View ARP Table ...55 View Bridge Table ...56 View Active DHCP Client Table ...56 View Network Activities...57 Chapter 8 Troubleshooting ...58 Appendix A. ASCII ...60 Appendix B. SSH Settings...61 Appendix C. GPL Declamation ...69
  • LevelOne WAB-6120 | Manual - Page 9
    FIGURE Figure 1 LEVELONE 150MBPS WIRELESS POE AP 2 Figure 2 Typical Application ...3 Figure 3 Move the Cover...7 Figure 4 Figure 34 Remote Settings ...39 Figure 37 Coovachilli Settings...42 Figure 38 Upgrade Firmware ...43 Figure 39 Backup/Retrieve Settings ...44 Figure 40 Restore Settings ...45
  • LevelOne WAB-6120 | Manual - Page 10
    Figure 48 Antenna Alignment ...51 Figure 49 Speed Test ...52 Figure 56 Network Activities...57
  • LevelOne WAB-6120 | Manual - Page 11
    TABLE Table 1 LEVELONE 150MBPS WIRELESS POE AP Factory Default Settings 13 Table 2 ACSII ...60 Table 3 CLI Commands...61 Table 4 Public Software Name and Description 70
  • LevelOne WAB-6120 | Manual - Page 12
    wireless device and higher bandwidth with longer range for outdoor applications. The LEVELONE 150MBPS WIRELESS POE AP supports four wireless communication connectivity (AP, Wireless the LEVELONE 150MBPS WIRELESS POE AP is an ideal wireless broadband solution for wireless Internet service providers
  • LevelOne WAB-6120 | Manual - Page 13
    1 LEVELONE 150MBPS WIRELESS POE AP Key Features Compliant with IEEE 802.11b/g and IEEE 802.11n as well Support Passive Power over Ethernet which is supplied with 12V or 15V. High reliable watertight housing endures almost any harsh environments Four operating modes including AP, Wireless Client
  • LevelOne WAB-6120 | Manual - Page 14
    By default, it is set to AP mode which allows it to establish a wireless coverage; besides, it is also able to join any available wireless network under wireless client mode. The LEVELONE 150MBPS WIRELESS POE AP is able to deliver stable and efficient broadband connectivity for various applications
  • LevelOne WAB-6120 | Manual - Page 15
    as well as performance in mind when selecting your installation site, especially where there are electric power and phone lines. 4. When installing LEVELONE 150MBPS WIRELESS POE AP, please note the following things:  Do not use a metal ladder;  Do not work on a wet or windy day;  Wear shoes
  • LevelOne WAB-6120 | Manual - Page 16
    attaching the external antenna onto the LEVELONE 150MBPS WIRELESS POE AP; otherwise, damage might be caused to the LEVELONE 150MBPS WIRELESS POE AP itself. Product Package WAB-6120 PoE Injector DC Adapter Clamp RJ-45 Ethernet Cable Quick installation Guide CD Manual Note: Product CD contains Quick
  • LevelOne WAB-6120 | Manual - Page 17
    Pole Mounting Ring Power Cord & PoE Injector Warning: Users MUST use the "Power cord & PoE Injector" shipped in the box with the LEVELONE 150MBPS WIRELESS POE AP. Use of other options will cause damage to the LEVELONE 150MBPS WIRELESS POE AP. Chapter 2 Hardware Installation Page 6
  • LevelOne WAB-6120 | Manual - Page 18
    Hardware Installation Connect up 1. The bottom of the LEVELONE 150MBPS WIRELESS POE AP is a movable cover. Grab the cover and pull it back harder to take it out as the figure shown below. Figure 3 Move the
  • LevelOne WAB-6120 | Manual - Page 19
    3. Slide the cover back to seal the bottom of the LEVELONE 150MBPS WIRELESS POE AP. Figure 5 Seal the Bottom 4. Plug the power cord into the DC port of the PoE injector as the following right picture shows. Figure 6 Connect to PoE Injector Chapter 2 Hardware Installation Page 8
  • LevelOne WAB-6120 | Manual - Page 20
    5. Plug the other side of the Ethernet cable as shown in Step 3 into the PoE port of the PoE injector and get the complete set ready. Figure 7 Complete Set Chapter 2 Hardware Installation Page 9
  • LevelOne WAB-6120 | Manual - Page 21
    should unlock the pole mounting ring with a screw driver before putting it through LEVELONE 150MBPS WIRELESS POE AP as the following right picture shows. Figure 8 Pole Mounting - Step 1 2. Mount LEVELONE 150MBPS WIRELESS POE AP steadily to the pole by locking the pole mounting ring tightly. Figure
  • LevelOne WAB-6120 | Manual - Page 22
    3. Now you have completed the hardware installation of LEVELONE 150MBPS WIRELESS POE AP. Figure 10 Pole Mounting - Step 3 Chapter 2 Hardware Installation Page 11
  • LevelOne WAB-6120 | Manual - Page 23
    for your application instead of the built-in directional antenna, please follow the steps below. 1. Grab the black rubber on the top of LEVELONE 150MBPS WIRELESS POE AP, and slightly pull it up. The metal N-type connector will appear. Figure 11 Move the Rubber 2. Connect your antenna with the
  • LevelOne WAB-6120 | Manual - Page 24
    Settings". Table 1 LEVELONE 150MBPS WIRELESS POE AP Factory Default Settings Features Username Password Wireless Device Name Operating admin admin WAB-6120-xxxxxx (model name + 6 MAC digits) AP Auto 192.168.1.1 255.255.255.0 0.0.0.0 0.0.0.0 0.0.0.0 Enable 802.11b/g/n 6 LevelOne Enable Disable
  • LevelOne WAB-6120 | Manual - Page 25
    Encryption Wireless Separation Access Control Enable/Disable Read Community Name SNMP Write Community above, Netscape or Firefox. or Google Chrome How to Login the Web-based Interface The LEVELONE 150MBPS WIRELESS POE AP provides you with user-friendly Web-based management tool. Open Web browser and
  • LevelOne WAB-6120 | Manual - Page 26
    Figure 12 Login Page Chapter 3 Basic Settings Page 15
  • LevelOne WAB-6120 | Manual - Page 27
    : admin) respectively and click "Login" to login the main page of LEVELONE 150MBPS WIRELESS POE AP. As you can see, this management interface provides five main options in the black bar above, which are Status, System, Wireless, Management and Tools. Figure 13 Main Page Note: The username and
  • LevelOne WAB-6120 | Manual - Page 28
    Basic System Settings For users who use the LEVELONE 150MBPS WIRELESS POE AP for the first time, it is provides path redundancy while preventing loops in a network. STP allows only one active path at a time between the access points but establish the redundant link as a backup if the initial link
  • LevelOne WAB-6120 | Manual - Page 29
    the new IP address. For an immediate access to the bridge, please flush the netbios cache on the client computer by running the "nbtstat -r" command before using the device name of the CPE to access its Web Management page. In case the LEVELONE 150MBPS WIRELESS POE AP is unable to obtain an IP
  • LevelOne WAB-6120 | Manual - Page 30
    the CPE manually. Make sure the specified IP address is unique on your network in order to prevent IP conflict. If the LEVELONE 150MBPS WIRELESS POE AP is configured as Router mode, you need to configure some additional TCP/IP parameters for accessing the
  • LevelOne WAB-6120 | Manual - Page 31
    is on wired port and LAN is on wireless port. Thus users must also connect the CPE with another wireless device before it is set to Router mode and access the CPE via the connected wireless device. Time Settings Compliant with NTP, the LEVELONE 150MBPS WIRELESS POE AP is capable of keeping its time
  • LevelOne WAB-6120 | Manual - Page 32
    Select the time server from the "NTP Server" dropdown list or manually input the IP address of available time server into "Manual IP". Hit "Apply" to save settings. RADIUS Settings RADIUS (Remote Authentication Dial-In User Service) is a server for remote user authentication and accounting; playing
  • LevelOne WAB-6120 | Manual - Page 33
    firewall is a system or group of systems that enforce an access control policy between two networks. It may also be defined as a mechanism used to protect a trusted network from an un-trusted network. LEVELONE 150MBPS WIRELESS POE AP has capabilities of Source IP Filtering, Destination IP Filtering
  • LevelOne WAB-6120 | Manual - Page 34
    Port Filtering: The source port filtering enable you to restrict certain ports of data packets from your local network to Internet through LEVELONE 150MBPS WIRELESS POE AP. Use of such filters can be helpful in securing or restricting your local network. Figure 21 Source Port Filtering Chapter
  • LevelOne WAB-6120 | Manual - Page 35
    to automatically redirect common network services to a specific machine behind the NAT firewall. These settings ne are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind LEVELONE 150MBPS WIRELESS POE AP's NAT firewall. Chapter
  • LevelOne WAB-6120 | Manual - Page 36
    to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to the Internet traffic, such as Web (HTTP) servers, FTP servers, SMTP (e-mail) servers and DNS servers. Figure 24 DMZ Basic Wireless Settings Open
  • LevelOne WAB-6120 | Manual - Page 37
    LEVELONE 150MBPS WIRELESS POE AP can provide connectivity services for CPEs under Bridge mode. Wireless Network Name (SSID) This wireless network name is shared among all associated devices in your wireless mode, wireless client can be divided into HT STA and Non-HT STA, among which the one with
  • LevelOne WAB-6120 | Manual - Page 38
    Upper Channel and Lower Channel. Channel Mode Four levels are available: 5MHz, 10MHz, 20MHz and 40MHz. The last one can enhance data throughput, but it takes more bandwidth, thus it might cause potential interference. Antenna By default, LEVELONE 150MBPS WIRELESS POE AP uses its built-in antenna for
  • LevelOne WAB-6120 | Manual - Page 39
    of the AP while displays the one of associated wireless client or the MAC address designated manually. Site Survey Under wireless client mode, the LEVELONE 150MBPS WIRELESS POE AP is able to perform site survey, through which, information on the available access points will be detected. Open "Basic
  • LevelOne WAB-6120 | Manual - Page 40
    Profile Settings Available in AP mode, the LEVELONE 150MBPS WIRELESS POE AP allows up to 16 virtual check the Enable box of the profile and click on the profile (eg. Profile 2) to configure wireless and security settings. Hit Apply to active the profile. Figure 15 VAP Profile Settings Chapter 3
  • LevelOne WAB-6120 | Manual - Page 41
    may own a higher priority than common one. To enable WMM, the wireless client should also support it Max. Station Number: By checking one SSID to a VLAN, and client devices using the SSID are grouped in that VLAN. To allow users on the VLAN to access the WEB page of the LEVELONE 150MBPS WIRELESS
  • LevelOne WAB-6120 | Manual - Page 42
    of accessing the Web page of the LEVELONE 150MBPS WIRELESS POE AP. Figure 17 Management VLAN ID Chapter 3 Basic Settings Page 31
  • LevelOne WAB-6120 | Manual - Page 43
    enabled; however, if your wireless clients don't support A-MPDU/A-MSDU aggregation, it is not recommended to enable it. Short GI Under 802.11n mode, enable it to obtain better data rate if there is no negative compatibility issue. RTS Threshold The LEVELONE 150MBPS WIRELESS POE AP sends RTS
  • LevelOne WAB-6120 | Manual - Page 44
    20 and 1024. DTIM Interval DTIM, which stands for Delivery Traffic Indication Message, is contained in the data packets. It is for enhancing the wireless transmission efficiency. The default is set to 1. Enter a value between 1 and 255. Preamble Type It defines some details on the 802.11 physical
  • LevelOne WAB-6120 | Manual - Page 45
    ; any modification on them may negatively impact the performance of your wireless network. Wireless Security Settings To prevent unauthorized radios from accessing data transmitting over the connectivity, the LEVELONE 150MBPS WIRELESS POE AP provides you with rock solid security settings. Security
  • LevelOne WAB-6120 | Manual - Page 46
    the rights to access the wireless network and wired Ethernet. With User and PC identity, centralized authentication as well as dynamic key management, it controls the security risk of wireless network to the lowest. To serve the 802.1x, at least one EAP type should be supported by the RADIUS
  • LevelOne WAB-6120 | Manual - Page 47
    . WPA2-PSK: As a new version of WPA, only all the clients support WPA2, can it be available. If it is selected, the data encryption wireless security on your network! Only setting the same Authentication, Data Encryption and Key in the LEVELONE 150MBPS WIRELESS POE AP and other associated wireless
  • LevelOne WAB-6120 | Manual - Page 48
    Control appoints the authority to wireless client on accessing LEVELONE 150MBPS WIRELESS POE AP, thus a further security mechanism is provided. This function is available only under AP mode. Open "Access Control" in "Wireless" as below. Figure 32 Access Control Access Control Mode If you select
  • LevelOne WAB-6120 | Manual - Page 49
    Extend the range of your network without having to use cables to link the Access Points by using the Wireless Distribution System (WDS): Simply put, you can link the Access Points wirelessly. Open "WDS Settings" in "Wireless" as below: Figure 33 WDS Settings Enter the MAC address of another AP you
  • LevelOne WAB-6120 | Manual - Page 50
    "Secure". You may also choose "Customized" to enable any methods as desired. Figure 18 Remote Settings SNMP Management The LEVELONE 150MBPS WIRELESS POE AP supports SNMP for convenient remote management. Open "Remote Settings" in "Management" shown below. Set the SNMP parameters and obtain MIB
  • LevelOne WAB-6120 | Manual - Page 51
    Protocol Version Select the SNMP version, and keep it identical on the LEVELONE 150MBPS WIRELESS POE AP and the SNMP manager. The LEVELONE 150MBPS WIRELESS POE AP supports SNMP v2/v3. Server Port Change the server port for a service if needed; however you have to use the same port to use
  • LevelOne WAB-6120 | Manual - Page 52
    or user. Only the SNMP commands carrying this password are allowed to access the LEVELONE 150MBPS WIRELESS POE AP. Confirm Password Input that password again to make sure it is your desired one. Access Type Select "Read Only" or "Read and Write" accordingly. Authentication Protocol Select
  • LevelOne WAB-6120 | Manual - Page 53
    easily and securely access the Internet. Under Router mode, when Coovachilli is enabled, the LEVELONE 150MBPS WIRELESS POE AP Access Point will force an HTTP use Coovachilli, you need to find Coovachilli service providers that have the additional services needed to make Coovahcilli work. Figure 19
  • LevelOne WAB-6120 | Manual - Page 54
    server UAM Secret: Enter the secret password between the redirect URL and the Hotspot. Upgrade Firmware Open "Firmware Upload" in "Management" and follow the steps below to upgrade firmware locally or remotely through LEVELONE 150MBPS WIRELESS POE AP's Web: Chapter 5 Management Figure 20 Upgrade
  • LevelOne WAB-6120 | Manual - Page 55
    Click "Browse" to select the firmware file you would like to load; Click "Upload" to start the upload up configuration information in case of something unexpected. If tragedy hits your device, you may have an access to restore the important files by the backup. All these can be done by the local or
  • LevelOne WAB-6120 | Manual - Page 56
    and reboot your device, then default settings are applied. Figure 22 Restore Settings Restore factory default settings via Reset Button If software in LEVELONE 150MBPS WIRELESS POE AP is unexpectedly crashed and no longer reset the unit via Web, you may do hardware reset via the reset button. Press
  • LevelOne WAB-6120 | Manual - Page 57
    Figure 23 Reboot Password From "Password Settings" in "Management", you can change the password to manage your LEVELONE 150MBPS WIRELESS POE AP. Enter the new password respectively in "New Password" and "Confirm Password" fields; click "Apply" to save settings. Figure 24 Password Note: The password
  • LevelOne WAB-6120 | Manual - Page 58
    Certificate Settings Under Client mode, when EAP-TLS is used, the RADIUS server must know which user certificates to trust. The Server can trust all certificates issued by a given CA. To import a user certificate, from Import User Certificates, click "Browse" and specify the location where the user
  • LevelOne WAB-6120 | Manual - Page 59
    Chapter 6 Monitoring Tools System Log System log is used for recording events occurred on the LEVELONE 150MBPS WIRELESS POE AP, including station connection, disconnection, system reboot and etc. Open "System Log" in "Tools" as below. Figure 26 System Log Remote Syslog Server Enable
  • LevelOne WAB-6120 | Manual - Page 60
    Site Survey Only available under Wireless Client mode, site survey allows you to scan all the APs within coverage. Open "Site Survey" in "Tools" as below and select the desired AP
  • LevelOne WAB-6120 | Manual - Page 61
    to ping. Ping Interval: Specify the interval time to ping the remote unit. Startup Delay: Specify the startup delay time to prevent reboot before the LEVELONE 150MBPS WIRELESS POE AP is fully initialized. Failure Count To Reboot: If the ping timeout packets reached the value, the
  • LevelOne WAB-6120 | Manual - Page 62
    Figure 30 Antenna Alignment Speed Test The speed test is to monitor the current data transmission (TX) and data reception (RX) rate with the remote LEVELONE 150MBPS WIRELESS POE AP. Enter the IP address of the remote CPE, type in the user name/password and click "Test". The result will display in
  • LevelOne WAB-6120 | Manual - Page 63
    Figure 31 Speed Test Chapter 6 Status Page 52
  • LevelOne WAB-6120 | Manual - Page 64
    to have the real-time information. Figure 50 Basic Information View Association List Open "Connections" in "Status" to check the information of associated wireless devices such as MAC address, signal strength, connection time, IP address, etc. All is read only. Click "Refresh" at the bottom to
  • LevelOne WAB-6120 | Manual - Page 65
    data rate, current TX/RX packets. View Network Flow Statistics Open "Statistics" in "Status" to check the data packets received on and transmitted from the wireless and Ethernet ports. Click "Refresh" to view current statistics. Chapter 6 Status Page 54
  • LevelOne WAB-6120 | Manual - Page 66
    Figure 52 Network Flow Statistics Poll Interval Specify the refresh time interval in the box beside "Poll Interval" and click "Set Interval" to save settings. "Stop" helps to stop the auto refresh of network flow statistics. View ARP Table Open "ARP Table" in "Status" as below. Click "Refresh" to
  • LevelOne WAB-6120 | Manual - Page 67
    View Bridge Table Open "Bridge Table" in "Status" as below. Click "Refresh" to view current connected status.. Figure 54 Bridge View Active DHCP Client Table Open "DHCP Client List" in "Status" as below to check the assigned IP address, MAC address and time expired for each DHCP leased client. Click
  • LevelOne WAB-6120 | Manual - Page 68
    Activities The network activities allows you to monitor the current Wireless and Ethernet TX/RX data traffic in graphical and numerical the mean throughput value. Throughput statistics can be updated manually using the "Refresh" button. Figure 32 Network Activities Chapter 6 Status Page 57
  • LevelOne WAB-6120 | Manual - Page 69
    troubleshooting procedures for basic problems with the LEVELONE 150MBPS WIRELESS POE AP. For warranty assistance, contact your service provider or distributor for the process. Q 1. How to know the MAC address of LEVELONE 150MBPS WIRELESS What if I can not access the Web-based management interface?
  • LevelOne WAB-6120 | Manual - Page 70
    Login the unit via other browsers such as Firefox.  Hardware reset the unit. Q 5. What if the wireless connection is not stable after associating with an AP under wireless client mode?  Since the LEVELONE 150MBPS WIRELESS POE AP comes with a built-in directional antenna, it is recommended make the
  • LevelOne WAB-6120 | Manual - Page 71
    Key (hexadecimal number or ACSII). As defined, hexadecimal number is represented by 0-9, A-F or a-f; ACSII is represented by 0-9, A-F, a-f or punctuation. Each one consists of two-digit hexadecimal. Table 2 ACSII ASCII Character 0 1 2 3 4 5 6 7 8 Hex Equivalent 21 22 23 24 25 26 27 28 29
  • LevelOne WAB-6120 | Manual - Page 72
    --current system time --time zone -- NTP Update --server type -IP -Manual IP --system setting --system firmware version --system MAC address --system name --country/region --ether port 1 settings --wan ip settings --router mode access type --static ip address Appendix B. GPL Declamation Page 61
  • LevelOne WAB-6120 | Manual - Page 73
    mask --dhcp server enable --dhcp server ip start --dhcp server ip end --dhcp server leasetime --dhcp relay enable --dhcp server ip --wlan setting --operation mode --wireless network name --wireless SSID broadcast Page 62
  • LevelOne WAB-6120 | Manual - Page 74
    --rate --antenna type --antenna gain setings --wmm settings --wireless isolate communication between clients --max sta connection number --Whether manually limit the number o f station --wireless bwa space in meter setting --wireless bwa coverage class setting --channel mode --channel offset of
  • LevelOne WAB-6120 | Manual - Page 75
    remote1 -remote2 -remote3 -remote4 Appendix B. GPL Declamation --wireless wep default key index --wireless wep key 1 --wireless wep key 2 --wireless wep key 3 --wireless wep key 4 --wireless WPA setting --wireless pre-shared key (PSK) for WPA-PSK --wireless WPA re-auth period (in seconds) --enable
  • LevelOne WAB-6120 | Manual - Page 76
    vlanID of this vap --wireless separation --WMM Support --Max Station Number --Whether manually limit the number o f station --wireless authentication type --wireless data encryption --wireless wep default key index --wireless WPA setting --list of associated wireless clients --vlan setting --enable
  • LevelOne WAB-6120 | Manual - Page 77
    https --enable wise tools --SNMP setting --Protocol Version --Server Port --SNMP Read Community --SNMP Write Community --Trap Destination --Trap Community --v3Admin --Enable SNMPv3Admin --name --password --access type --Authentication Protocol Page 66
  • LevelOne WAB-6120 | Manual - Page 78
    --privacy protocol -v3User --Enable SNMPv3User --name --password --access type --Authentication Protocol --privacy protocol --CoovaChilli setting --Coovachilli --startup delay --failure count --ip address --access control --enable wireless access control (ACL) --delete a local ACL Page 67
  • LevelOne WAB-6120 | Manual - Page 79
    √ password √ reset √ reboot √ exit address --delete or display all local ACL address --add mac address to Current Access Control List --statistics --Wireless LAN --Ethernet LAN --syslog list --system password --restore factory --reboot system --logout from CLI Appendix B. GPL Declamation
  • LevelOne WAB-6120 | Manual - Page 80
    Appendix C. GPL Declamation PUBLIC SOFTWARE DECLAMATION In the software we delivered, there may contains some public software, if it is, please read below carefully: 1. Definition "Public Software", when applicable, shall mean that portion of the Licensed Software, in source code form, set forth
  • LevelOne WAB-6120 | Manual - Page 81
    to any such Public Software, as set forth in its presentation on website. 3. Limited Liability The supplier hereby express that the supplier shall have no liability for any costs, loss or damages resulting from Licensee's breach of the terms and conditions applicable to use, conversion or
  • LevelOne WAB-6120 | Manual - Page 82
    dropbear hostapd wpa_sup plicant mtdutil ntpclient procps vsftpd Copyright (c) 2002-2006 Matt Johnston Portions copyright (c) 2004 Mihnea Stoenescu Copyright (c) 2002-2006, Jouni Malinen and contributors Copyright (c) 2003-2005, Jouni Malinen
  • LevelOne WAB-6120 | Manual - Page 83
    linux .beasts.or g/users/ce vans/vsftp d-1.1.2.tar. gz ftp://ftp.ker nel.org/pu b/linux/ker nel/v2.6/lin ux-2.6.20.3 .tar.bz2 LICENSE Version 2 GNU GENERAL PUBLIC LICENSE Version 2 rg/licenses/old-li censes/gpl-2.0.ht ml http://www.gnu.o rg/licenses/old-li censes/gpl-2.0.ht ml Appendix B. GPL
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
LevelOne
WAB-6120
150Mbps
Wireless Outdoor PoE AP
User Manual
V1.2