LevelOne POS-1002 Quick Install Guide

LevelOne POS-1002 Manual

Get LevelOne POS-1002 PDF manuals and user guides View all LevelOne POS-1002 manuals
Add to My Manuals
Save this manual to your list of manuals

LevelOne POS-1002 manual content summary:

  • LevelOne POS-1002 | Quick Install Guide - Page 1
    & Splitter POI-3004 Gigabit PoE Injector POI-3000 & POS-3000 Gigabit PoE Plus Injector & Splitter POI-3002 & POS-3000 PoE Plus Injector & Splitter Quick Installation Guide English Dansk Slovenščina Deutsch Italiano Français 한국어 Españ ol Nederlands Português Svenska Polish
  • LevelOne POS-1002 | Quick Install Guide - Page 2
    Installation Steps Step 1.  Connect AC Power cord to the PoE Injector, and "Power" LED will light up.  Schließ en Sie das Netzkabel an den PoE-Injektor an und die "Power"-LED leuchtet auf.  Connectez le cordon d'alimentation secteur sur l'injecteur PoE, le voyant DEL "Power" (Alimentation) s'
  • LevelOne POS-1002 | Quick Install Guide - Page 3
    Step 2.  Connect "Data/In" port of Injector to Non PoE switch via Cat.5e/6/7 cable, and set the correct voltage (5V, 9V or 12V) by adjustable DIP switch on the side of PoE Splitter. (default setting 5V)  Verbinden Sie den "Data/IN"-Port des Injektors über ein Cat.5e/6/7-Kabel mit dem Nicht-PoE-
  • LevelOne POS-1002 | Quick Install Guide - Page 4
     Conecte a porta "Data/In" (Dados/Entrada) do injector ao switch não PoE através de um cabo Cat.5e/6/7 e defina a voltagem correcta (5V, 9V ou 12V) através do comutador DIP regulável situado na parte lateral do PoE Splitter. (a definição padrão é de 5V)  Anslut Data/in porten på injektorn till en
  • LevelOne POS-1002 | Quick Install Guide - Page 5
    Power + Data Splitter P+D/out Injector Ethernet Power" LED Splitter  Ligue a porta "Power+Data" (Entrada de Dados) do Separador e a porta "P+D/Out" (P+D/Saída) do Injector através do cabo Ethernet e certifique-se de que o indicador LED "Power" (Energia) está ligado.  Förbind "Power+Data"
  • LevelOne POS-1002 | Quick Install Guide - Page 6
    (gegevensuitgang) van de splitter aan op de RJ45-poort van het netwerkapparaat. (Zorg dat u de juiste verwisselbare pen kiest voor het aandrijven van niet-PoE-apparaten.)  Forbind "Power OUT" kablet på splitter til power jack på den tilknyttede netværks enhed og forbind "Data OUT" kablet på
  • LevelOne POS-1002 | Quick Install Guide - Page 7
    Step 5.  Check whether the network device is on. If not, please make sure that power is on for Injector and Splitter, and all cables are connected correctly.  Prüfen Sie, ob das Netzwerk-Gerät eingeschaltet ist. Wenn dies nicht der Fall ist, stellen Sie bitte sicher, dass die Stromversorgung für
  • LevelOne POS-1002 | Quick Install Guide - Page 8
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
POI-2001 & POS-1001
Gigabit PoE Injector & Splitter
POI-2002 & POS-1002
PoE Injector & Splitter
POI-3004
Gigabit PoE Injector
POI-3000 & POS-3000
Gigabit PoE Plus Injector & Splitter
POI-3002 & POS-3000
PoE Plus Injector & Splitter
Quick Installation Guide
English
Deutsch
Français
Español
Nederlands
Dansk
Italiano
Ελληνικά
Português
Svenska
Slovenščina
繁體中文
한국어
Русский
Polish