Lantronix C2110 Series C2110 Series Datasheet PDF 256.73 KB

C2110 Series

ION Fast Ethernet Media Converter Module

100Base-TX to 100Base-FX

Ordering Information

C2110-1011

100Base-TX (RJ-45) [100 m/328 ft.]

to 100Base-FX 1300nm multimode (ST)

[2 km/1.2 mi.] Link Budget: 11.0 dB

C2110-1013

100Base-TX (RJ-45) [100 m/328 ft.]

to 100Base-FX 1300nm multimode (SC)


C2110-1039

100Base-TX (RJ-45) [100 m/328 ft.]

to 100Base-FX 1300nm multimode (LC)


C2110-1014

100Base-TX (RJ-45) [100 m/328 ft.]

to 100Base-FX 1310nm single mode (SC)


C2110-1019

100Base-TX (RJ-45) [100 m/328 ft.]

to 100Base-FX 1310nm single mode (LC)


C2110-1040

100Base-TX (RJ-45) [100 m/328 ft.]

to 100Base-X SFP Slot (empty)

Op°onal Accessories

(sold separately)

SFP Modules

25

+1.952.941.7600 | www.transi°on.com | sales@transi°on.com

C2110-1013

Media Converters

Specifications

Standards

IEEE 802.3

Data Rate

100 Mbps, Layer 1

Switches

SW1: Auto-Negotiation (UP = enabled)

SW2: Pause (UP=enabled)

SW3: Link Pass Through (UP = enabled)

SW4: Far-End-Fault (FEF) (UP = enabled)

Internal Jumpers

Auto-MDI/MDIX: Enable/Disable

Jumpers

Hardware: Mode of operation is determined by the

settings on the 4-position switch

Software: Mode of operation is determined by the

most recently saved on-board microprocessor settings

Status LEDs

PWR (Power): ON = Connection to powered backplane

LKC (Copper Link): ON = Copper Link

RXC (Receive Copper): Blinking = Data received

on Copper link

LKF (Fiber Link): ON = Fiber Link

RXF (Receive Fiber): Blinking = Data received on Fiber

Link

Dimensions

Width: 0.86” [22 mm]

Depth: 6.5” [165 mm]

Height: 3.4” [86 mm]

Power Consumption

2.5 Watts, 200 mA @ 13.9 VDC

Environment

Environment specs are dependent on the chassis

chosen

Operating: 0±C to 50±C

Humidity: 5% to 95% (non-condensing)

Altitude: 0 – 10,000 ft.

Weight

1 lb. [0.45 kg]

MTBF

Greater than 250,000 hours (MIL-HDBK-217F)

Greater than 667,500 hours (Bellcore)

Certifications

CISPR/EN55022 Class A, FCC Class A, CE Mark

Warranty

Lifetime

The ION C2110 is a media converter module that provides an

interface between 100Base-TX ports and 100Base-FX ports,

allowing users to integrate fiber optic cabling into 100Base-TX

copper environments. Operating at Layer 1, the physical layer,

data is passed through the converter at line speed, making it

ideal for applications where low latency is essential. The ION

C2110 is a manageable device when installed in a managed

ION chassis.

Features

●

Auto-Negotiation of speed and

duplex on TP port

●

Auto-MDI/MDIX on TP port

●

Link Pass Through (LPT)

●

Far-End-Fault (FEF) detection

●

Automatic Link Restoration

●

Pause advertisement

●

Field Upgradeable Firmware

●

Can be used in any ION Platform

Chassis

●

Standards based, will link with any

Standard 100Base-TX and any

Standard 100Base-FX ports

Manageable Features

●

Report converter status to chassis

management software:

–

TP and Fiber Link Status

–

Hardware switch settings

–

Copper Port Speed

–

TP and Fiber Port Duplex

–

Fault condition

●

Write operation includes:

–

Power on/off device

–

Auto-Negotiation enable/disable

–

Force 10 Mbps or 100 Mbps

–

Force half or full-duplex

–

Select advertising modes when

Auto-Negotiation is enabled

–

LPT enable/disable

–

FEF enable/disable

–

Pause enable/disable

–

Auto-MDI/MDIX enable/disable

Note: Manageable Features are available when

used in an ION Platform chassis along with

an ION Management Module.

081220

Lantronix C2110 Series C2110 Series Datasheet PDF 256.73 KB

Lantronix C2110 Series Manual

Lantronix C2110 Series manual content summary: