Kenwood TK-3360 User Manual 2

Kenwood TK-3360 Manual

Get Kenwood TK-3360 PDF manuals and user guides View all Kenwood TK-3360 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-3360 manual content summary:

  • Kenwood TK-3360 | User Manual 2 - Page 1
    INSTRUCTION MANUAL UHF FM TRANSCEIVER TK-3360 © B62-2211-00 (X) 09 08 07 06 05 04 03 02 01 00
  • Kenwood TK-3360 | User Manual 2 - Page 2
    you have chosen Kenwood for your land mobile radio applications. Notices to the User ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified
  • Kenwood TK-3360 | User Manual 2 - Page 3
    battery pack. • Do not use options not specified by Kenwood. • If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts the battery pack. • Do not immerse the transceiver in water. • Always switch the transceiver power off before installing optional accessories. •
  • Kenwood TK-3360 | User Manual 2 - Page 4
    parts are exposed from the antenna covering. Transmitting at such a time may result in a high-frequency burn. • If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, remove the battery pack from the transceiver, and contact your Kenwood
  • Kenwood TK-3360 | User Manual 2 - Page 5
    is melted, the gas release vent or safety function is damaged, or the electrolyte is ignited, the battery may generate heat or smoke, rupture, or burst into flame. • Do not leave the battery near fires, stoves, or other heat generators (areas reaching over 80°C/ 176°F)! If the polymer separator is
  • Kenwood TK-3360 | User Manual 2 - Page 6
    generate heat or smoke, rupture, or burst into flame. • Use only the specified charger and observe charging requirements! If the battery is charged in unspecified conditions (under high temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodelled
  • Kenwood TK-3360 | User Manual 2 - Page 7
    water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems. • Do not charge the battery for longer than the specified time! If the battery pack has not finished charging even after the regulated time has passed, stop it. The
  • Kenwood TK-3360 | User Manual 2 - Page 8
    EQUIPMENT Note: These unpacking instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. Carefully unpack the transceiver. If any items are missing or damaged, file a claim with the carrier immediately. Supplied Accessories Belt clip 1 Speaker
  • Kenwood TK-3360 | User Manual 2 - Page 9
    the safety catch, press the release latch, then pull the battery pack away from the transceiver. 2 1 3 Note: ◆ For battery pack charging procedures and useage, refer to the battery charger Instruction Manual. ◆ Before charging a battery pack that is attached to the transceiver, ensure that the
  • Kenwood TK-3360 | User Manual 2 - Page 10
    setting on your transceiver). If you want to transmit a stronger signal (using the high power setting on your transceiver), use an optional rechargeable battery pack. 1 To open the battery case, press on the two tabs on the upper rear of the case, then pull the two halvs apart. 2 Insert 6 AA (LR6
  • Kenwood TK-3360 | User Manual 2 - Page 11
    Installing the Belt Clip Note: When first installing the belt clip, you must remove the battery pack from the rear of the transceiver. 1 Remove the 2 screws from the rear of the transceiver, then remove the small, plastic black covering that was
  • Kenwood TK-3360 | User Manual 2 - Page 12
    2 While holding the cap in place, push it towards the bottom of the transceiver until the tabs on the cap click into place. • To remove the cap, hold the top of the cap in place with your finger while inserting a 3 mm or smaller flat blade screwdriver under the bottom of the cap. Slowly slide the
  • Kenwood TK-3360 | User Manual 2 - Page 13
    available, depending on the number of channels used (4 channel type: white, 8 channel type: gray, and 12 channel type: black). 1 Set the Selector knob to channel 1, then pull the Selector knob off the transciever. • If the Selector is not positioned at channel 1, the Selector knob may not install
  • Kenwood TK-3360 | User Manual 2 - Page 14
    a channel. ② Power switch/ Volume control Rotate to turn the transceiver ON/OFF and to adjust the volume. ③ Transmit/ Receive/ Battery low indicator If enabled by your dealer, lights red while transmitting, green while receiving a call, and orange or blue (depending on dealer programming) when
  • Kenwood TK-3360 | User Manual 2 - Page 15
    can be accessed by either pressing the key or by pressing and holding the key. Ask your dealer for details. n None No function has been programmed. n Activity Detection Press this key to toggle Activity Detection ON and OFF. If an event occurs while Activity Detection is enabled, the transceiver
  • Kenwood TK-3360 | User Manual 2 - Page 16
    the DTMF number that has been programmed onto your selected channel. Your dealer may program different DTMF numbers on different channels. n Battery Indicator Press this key to announce the current battery energy level. Battery level 4 (green LED) means the battery is full, level 3 (orange LED) is
  • Kenwood TK-3360 | User Manual 2 - Page 17
    function ON or OFF. If the transceiver is not operated for the pre-programmed time, it will emit a Lone Worker tone. Subsequently, if no operation is this key to change the transmit power on the current channel to low power, to conserve battery energy. n Monitor Press this key to deactivate QT or
  • Kenwood TK-3360 | User Manual 2 - Page 18
    and only stops if a signal is present. n Scan Temporary Delete When scan pauses at an undesired channel, you can temporarily remove that channel from the scanning sequence by pressing this key. n Scrambler Press this key to toggle the Scrambler function ON and OFF. The Scrambler allows you to
  • Kenwood TK-3360 | User Manual 2 - Page 19
    / Volume control to adjust the volume. Clockwise increases the volume and counterclockwise decreases it. Selecting a Channel Select your desired channel using the Selector knob. Each channel is programmed with settings for transmitting and receiving. Transmitting/ Receiving 1 Select your desired
  • Kenwood TK-3360 | User Manual 2 - Page 20
    the PTT switch to receive. • For best sound quality, hold the transceiver approximately 1.5 inches (3 ~ 4 cm) from your mouth. • If signaling has been programmed on the channel, you will hear a call only if the received signal matches your transceiver settings. SCAN Scan monitors for signals on the
  • Kenwood TK-3360 | User Manual 2 - Page 21
    in the scanning sequence. Scan Revert The Scan Revert channel is the channel selected when you press the PTT switch to transmit during scan. Your dealer can program one of the following types of Scan Revert channels: • Selected: The last channel selected before scan. • Selected + Talkback: Same as
  • Kenwood TK-3360 | User Manual 2 - Page 22
    Calling) A Selcall is a voice call to a station or group of stations. ■ Transmitting 1 Select your desired FleetSync channel. • Your dealer can program different ID codes on different channels. 2 Press the PTT switch and begin your conversation. ■ Receiving If enabled by your dealer, an alert tone
  • Kenwood TK-3360 | User Manual 2 - Page 23
    the squelch only when the transceiver receives the 5 tones programmed in your transceiver. Transceivers that do not transmit the correct to a particular station or to a group of stations. 1 Select your desired zone and channel. 2 Press the Call 1 or Call 2 key to transmit the 5-tone codes assigned
  • Kenwood TK-3360 | User Manual 2 - Page 24
    VOICE OPERATED TRANSMISSION (VOX) VOX operation allows you to transmit hands-free. This feature can be activated or deactivated by your dealer. VOX Gain Level 1 Connect a headset to the transceiver. 2 With the transceiver power off, press and hold the Side 1 key for 2 seconds while turning the
  • Kenwood TK-3360 | User Manual 2 - Page 25
    to blink red when the battery power is low. Recharge or replace the battery pack at this time. PTT ID PTT ID is the transceiver unique ID code which is sent each time the PTT switch is pressed and/or released. Compander If programmed by your dealer for a channel, the compander will remove excessive
  • Kenwood TK-3360 | User Manual 2 - Page 26
    is cancelled when the transceiver receives a call with a revive code. Optional Signaling Your dealer may also program several types of optional signaling for your transceiver channels. 5-tone Signaling: 5-tone Signaling opens the squelch only when your transceiver receives a call containing matching
  • Kenwood TK-3360 | User Manual 2 - Page 27
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
© B62-2211-00 (X)
09 08 07 06 05 04 03 02 01 00
INSTRUCTION MANUAL
UHF FM TRANSCEIVER
TK-3360