Home » Kenwood Manuals » Electronics Accessories » Kenwood TK-260G » Manual Viewer

Kenwood TK-260G User Manual

Kenwood TK-260G Manual

Get Kenwood TK-260G PDF manuals and user guides

View all Kenwood TK-260G manuals

Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-260G manual content summary:

Kenwood TK-260G | User Manual - Page 1
INSTRUCTION MANUAL MODE D'EMPLOI MANUAL DE INSTRUCCIONES BEDIENUNGSANLEITUNG GEBRUIKSAANWIJZING TK-260G/ TK-360G VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER EMETTEUR-RECEPTEUR FM VHF/ EMETTEUR-RECEPTEUR FM UHF TRANSCEPTOR DE FM VHF/ TRANSCEPTOR DE FM UHF VHF-FM-
Kenwood TK-260G | User Manual - Page 2
ENGLISH TK-260G/ TK-360G VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL
Kenwood TK-260G | User Manual - Page 3
personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. MODELS COVERED BY THIS MANUAL • TK-260G: VHF FM Transceiver • TK-360G: UHF FM Transceiver
Kenwood TK-260G | User Manual - Page 4
, nor on unstable surfaces. • If an abnormal odor or smoke is detected coming from the transceiver, switch OFF the power immediately and remove the optional battery pack from the transceiver. Contact your KENWOOD dealer. i
Kenwood TK-260G | User Manual - Page 5
CONTENTS UNPACKING AND CHECKING EQUIPMENT 1 Supplied Accessories 1 PREPARATION 3 Charging the Optional NiCd Battery Pack 3 Installing/ Removing the Optional NiCd Battery Pack ..... 3 Installing the Antenna 4 Installing the Belt Clip 5 Installing the Cap over the Speaker/ Microphone Jacks ... 5
Kenwood TK-260G | User Manual - Page 6
X5 TK-260G (NT) T90-0680-X5 Antenna TK-260G (NE2) T90-0681-X5 1 TK-360G (E,NE) T90-0682-X5 TK-360G (E4,NE4) T90-0684-X5 Belt clip J29-0624-X3 1 Screw set N99-2012-X5 1 Speaker/ microphone jacks cap B09-0351-X3 1 Speaker/ microphone locking bracket J21-4493-X4 1 Instruction manual B62
Kenwood TK-260G | User Manual - Page 7
Antenna (TK-260G) Antenna (TK-360G) Belt clip Screw set Speaker/ microphone jacks cap Speaker/ microphone locking bracket 2
Kenwood TK-260G | User Manual - Page 8
; charge it before use (refer to the battery pack instruction manual). ◆ DO NOT RECHARGE THE BATTERY PACK IF IT IS ALREADY FULLY CHARGED. DOING SO MAY CAUSE THE LIFE OF THE BATTERY PACK TO SHORTEN OR THE BATTERY PACK MAY BE DAMAGED. ◆ AFTER RECHARGING THE BATTERY PACK, DISCONNECT IT FROM THE CHARGER
Kenwood TK-260G | User Manual - Page 9
1 Match the four grooves of the battery pack with the corresponding guides on the back of the transceiver. 2 Slide the battery pack along the back of the transceiver until the release latch on the base of the transceiver locks. 3 To remove the battery pack, pull back on the release latch and slide
Kenwood TK-260G | User Manual - Page 10
■ Installing the Belt Clip If necessary, attach the belt clip using the two supplied 3 x 8 mm screws. Note: If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment. ■ Installing the Cap over the Speaker/ Microphone
Kenwood TK-260G | User Manual - Page 11
while receiving. Flashes orange while receiving a 2-Tone or DTMF signal that matches the one set up in your transceiver. Flashes red when the battery power is low while transmitting. Power switch/ Volume control Turn clockwise to switch ON the transceiver. Rotate to adjust the volume. To switch
Kenwood TK-260G | User Manual - Page 12
PROGRAMMABLE AUXILIARY FUNCTIONS Side 1 key and Side 2 key can each be programmed with one of the following auxiliary functions: • Monitor A (Monitor Unmute-Momentary): Press and hold the Monitor key to hear background noise. Release the key to return to normal operation. • Monitor B (Monitor Unmute
Kenwood TK-260G | User Manual - Page 13
OPERATING BASICS ■ Switching Power ON/OFF Turn the Power switch/ Volume control clockwise to switch the transceiver ON. Turn the Power switch/ Volume control counterclockwise to switch the transceiver OFF. ■ Adjusting the Volume Rotate the Power switch/ Volume control to adjust the volume. Clockwise
Kenwood TK-260G | User Manual - Page 14
■ Placing a Call 1 Make sure no parties are currently transmitting on your selected channel. 2 Press the PTT switch and speak into the microphone in your normal speaking voice. • For best sound quality at the receiving station, hold the microphone approximately 1.5 inches (3 ~ 4 cm) from your mouth.
Kenwood TK-260G | User Manual - Page 15
(you cannot transmit). Release the PTT switch to stop the tone and return to receive mode. ■ Battery Voltage Level While transmitting, the transceiver automatically checks the battery voltage level. When the voltage level becomes low, the LED indicator flashes red. When a tone sounds, transmission
Kenwood TK-260G | User Manual - Page 16
CHANNEL CHART Model: TKSerial Number: Channel 1 2 3 4 5 6 7 8 Receive Transmit Decode Encode frequency frequency signalling signalling Dealer Name & Address: Dealer Telephone Number: ( ) Date Purchased: / / 11