Intermec PB50 Model AB13 Battery Instructions
Intermec PB50 Manual
 |
View all Intermec PB50 manuals
Add to My Manuals
Save this manual to your list of manuals |
Intermec PB50 manual content summary:
- Intermec PB50 | Model AB13 Battery Instructions - Page 1
charging times for a fully discharged battery. It may take less time to charge the battery depending on the state of the battery charge. Charging Accessory AC18 4-Bay Battery Charger PB50 Portable Label Printer PB51 Mobile Printer PW50 Workboard Printer Charging Time 4 hours 4 hours 4 hours - Intermec PB50 | Model AB13 Battery Instructions - Page 2
ES D'UNE MANIÈRE APPROPRIÉE. VOIR LES INSTRUCTIONS. Élimination appropriée des piles usagées beim Schutz der Umwelt eine wichtige Rolle: 1. Keine Altakkus im unsortierten Hausm . Usar apenas os modelos de carregadores da Intermec AC18, PB50, PB51 e PW50. O uso de um carregador incorreto pode
-
1 -
2
 |
 |
AB13
Battery Instructions
Use the Model AB13 (P/N 318-026-001) rechargeable Lithium-ion
(Li-ion) battery with the PB50, PB51, and PW50 printers.
Charging the Battery
You need to fully charge the battery before using it in your printer.
You can charge a battery after partial discharge without affecting
the original battery capacity. Use the next table to understand the
maximum charging times for a fully discharged battery. It may take less
time to charge the battery depending on the state of the battery charge.
Charging Accessory
Charging Time
AC18 4-Bay Battery Charger
4 hours
PB50 Portable Label Printer
4 hours
PB51 Mobile Printer
4 hours
PW50 Workboard Printer
4 hours
AB13 Battery Instructions
*943-122-003*
P/N 943-122-003
Worldwide Headquarters
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel
425.348.2600
fax 425.355.9551
www.intermec.com
© 2009 Intermec Technologies
Corporation. All rights reserved.
Important Recommendations
Charge the battery before use.
See “Charging the Battery” for approved charging methods. Use of this
battery in other devices could result in damage to the device or battery.
The temperature range for charging batteries is 0°C to 45°C (32°F to
113°F). Do not charge battery packs outside this range. For maximum
battery life, charge batteries at 25°C (77°F).
Do not store the battery at temperatures above 50°C (122°F), such
as inside a car on a hot day or in direct sunlight, as this may damage
the battery.
Battery usage by children should be supervised
.
Do not disassemble or open, crush, bend or deform, puncture, shred, or
burn.
Do not modify the battery or attempt to insert foreign objects into the
battery.
Do not solder directly to the battery contacts.
Do not immerse the battery in water.
Do not short circuit the battery. Keep the battery connector away from
metallic items.
Do not apply mechanical shocks or pressure to the battery.
Avoid dropping the battery or the printer. If you suspect that
the battery or printer is damaged, send it to an Intermec
service center for inspection.
Replace battery only with another Intermec battery Model AB13.
This
battery has been tested in accordance with applicable safety standards.
Contact your Intermec sales representative or distributor if this battery
is no longer available.
Discarded batteries may create a safety hazard. Before disposal,
cover the battery connector with electrical insulating tape.
Specifications
Design and specifications are subject to change without notice.
Physical Specifications
Product:
Intermec Model AB13 Lithium-ion battery
Dimensions:
71 x 54 x 38 mm (2.8 x 2.1 x 1.5 in)
Weight:
218 g (7.6 oz)
Capacity and Output Specifications
Maximum output:
x
16.8 V
Capacity:
2200 mAh (37 Wh)
Temperature and Humidity Specifications
Operating temperature:
-20°C to 60°C (-4°F to 140°F)
Charging temperature:
0°C to 45°C (32°F to 113°F)
Storage temperature:
-20°C to 60°C (-4°F to 140°F)
Relative humidity:
0% to 95% non-condensing
Note:
In the U.S.A., the EPA does not consider spent Li-ion
batteries as hazardous waste.
Caution: This battery pack may ignite, create a chemical burn hazard, explode, or
release toxic materials if mistreated. Do not incinerate, disassemble, or heat above
100°C (212°F). Do not short circuit; may cause burns. Keep away from children.
Use only Intermec charger Models AC18, PB50, PB51 and PW50. Use of incorrect
charger may present a risk of fire or explosion.
CONTAINS LITHIUM-ION
BATTERY. WASTE BATTERY MUST PROMPTLY BE RECYCLED OR DISPOSED
OF PROPERLY. SEE INSTRUCTIONS.
Proper Disposal of Waste Batteries
Some of the substances necessary for the proper functioning of batteries are considered harmful to the
environment and to human health. It is therefore important that those substances be kept out of the
environment.
You play an important role in the protection of the environment:
Keep all waste batteries out of unsorted trash.
1.
Dispose of all waste batteries in separate collection for treatment and recycling.
2.
Please contact Intermec for the collection option(s) available in your location.
Marking of the battery:
The wheeled-bin symbol indicates the requirement for separate collection of the battery.
1.
Two letters shown underneath the wheeled bin indicate the presence of a certain substance:
2.
Hg means Mercury is present
a.
Cd means Cadmium is present
b.
Pb means Lead is present
c.
The Moebius loop (chasing arrows) indicates that the battery is recyclable.
3.